Toshiba E Studio 207 User Manual

Setting up Network Settings (Printing Function)    89
Setting up the IPX/SPX
You can set the IPX/SPX protocol to enable the communication over IPX/SPX.
The IPX/SPX must be configured to enable Novell printing with NetWare server 5.1/6.5 over 
IPX/SPX.
1) Enable IPX/SPX
Select whether the IPX/SPX protocol is enabled or disabled.  Please enable this when con-
figuring Novell printing over the IPX/SPX network.
2) Frame Type
Select the desired frame type for IPX/SPX.
-Auto Sense
 — Select this to use an...

10 TopAccess ADMINISTRATION TAB PAGE - SETUP 
MENU (Printing Function)
90    Setting up Network Settings (Printing Function)
Setting up the Bonjour
In Bonjour, you can enable or disable the Bonjour networking that is available for Mac OS X 
10.3.x/10.4.x.
1) Enable Bonjour
Select whether the Bonjour is enabled or disabled.
2) Link-Local Host Name
Enter the DNS host name of this equipment.
3) Service Name
Enter the device name of this equipment that will be displayed in the Bonjour network.
1
2
3...

Setting up Network Settings (Printing Function)    91
Setting up the DNS session
In DNS Session, you can specify the DNS server to enable the FQDN (Fully Qualified Domain 
Name) rather than the IP address on  specifying each server address.
When the DNS service is enabled and the DNS se rver supports the dynamic DNS service, 
please set the DDNS Session as well.
	  P.92 “Setting up the DDNS session”
1) Enable DNS Select whether the DNS server is used or not.
2) Primary DNS Server Address Specify the IP...

10 TopAccess ADMINISTRATION TAB PAGE - SETUP 
MENU (Printing Function)
92    Setting up Network Settings (Printing Function)
Setting up the DDNS session
In DDNS Session, you can enable the Dynamic DNS service if the DNS server supports the 
dynamic DNS.
yWhen using DDNS and the IP address is assigned using DHCP, enter “006 DNS Servers” 
and “015 DNS Domain Name” in the DHCP Client to register the A record and PTR record of 
the equipment automatically using DDNS.
yWhen using DDNS, make sure the “Allow...

Setting up Network Settings (Printing Function)    93
Setting up the NetWare session
In NetWare Session, you can set the NetWare Bindery or NDS service.  This must be set when 
configuring a Novell printing environment.
1) Enable Bindery
Select whether the NetWare Bindery mode for Novell printing is enabled or disabled.  When 
you configure a Novell printing environment with the NetWare server in bindery mode, you 
must enable this.
2) Enable NDS
Select whether the NetWare NDS mode for Novell printing is...

10 TopAccess ADMINISTRATION TAB PAGE - SETUP 
MENU (Printing Function)
94    Setting up Network Settings (Printing Function)
Setting up the HTTP network service
In HTTP Network Service, you can enable or disable Web-based services such as TopAccess 
and IPP printing.
1) Enable HTTP Server
Select whether the Web-based TopAccess and IPP printing are enabled or disabled.
2) Primary Port Number
Enter the port number for the NIC HTTP server. Generally “80” is used for this port.
3) Secondary Port Number
Enter...

Setting up Network Settings (Printing Function)    95
Setting up the SNMP network service
In SNMP Network Service, you can enable or disable the SNMP to monitor the device status 
using a network monitoring utility.  If an administrator wants to monitor the device status with a 
monitoring utility, programmed to fit the MIB, you must enable the SNMP and SNMP Traps.
1) Enable SNMP
Select whether the SNMP monitoring with MIB is enabled or disabled.  This must be enabled 
to allow users to connect using the...

10 TopAccess ADMINISTRATION TAB PAGE - SETUP 
MENU (Printing Function)
96    Setting up Network Settings (Printing Function)
5) Enable Alerts Trap
Select whether sending a SNMP Traps when an alert condition occurs.
6) IP Trap Address 1-10
Enter the IP address where the SNMP Traps will be sent.  You can specify up to 10 
addresses.
7) IP Trap Community
Enter the trap community name for the IP Traps.
8) IPX Trap Address
Enter the IPX address where the SNMP Traps will be sent.
Downloaded From...

Setting up Copier Settings    97
Setting up Copier Settings
In the Copier submenu page in the Setup menu, an administrator can configure the copier set-
tings that initially apply to copy operations.
Some settings may not apply to the LCD of this equipment as soon as you save the settings.  
The settings will be updated by pressing the [FUNCTION CLEAR] button on the Control Panel 
or after an Auto Clear time period.
Setting the copier settings
1Access TopAccess in the administrator mode.
	 P.50...

10 TopAccess ADMINISTRATION TAB PAGE - SETUP 
MENU (Printing Function)
98    Setting up Copier Settings
5Click [OK] to apply the changes.
When using the Internet Explorer, the settings that are displayed in each field may not be 
changed even if you change the settings and click [Save].  However, the settings have 
been changed in the equipment.  In that case, click the Copier submenu then the page 
displays the current settings in each field.
Setting up the copier settings
In Copier Settings, you can...