Toshiba Bex4t2g Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.3 Loading Supplies
 
E2- 7 
2.3.1  Loading the Media  
 (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 10. Lower the Print Head Block.  
11. Once the media is loaded it may be necessary to set the Media 
Sensors used to detect the start position for label or tag. 
 
Setting the Feed Gap Sensor position
 
(1)  Manually move the Media Sensor so that the Feed Gap Sensor is 
positioned at the centre of the labels. (z indicates the position of the 
Feed Gap Sensor)....

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.3 Loading Supplies
 
E2- 8 
2.3.1  Loading the Media 
(Cont.) 
 12. Batch mode 
In batch mode, the media is continuously printed until the number of 
labels/tags specified in the issue command has been printed.  
 
 
  
 
 
 
 
 
 
 
 
 
13. Loading with peel off module
 
When the optional Strip Module is fitted, the label is automatically 
removed from the backing paper at the Strip Plate as each label is 
printed.  
 
(1)  Remove enough labels from the...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.3 Loading Supplies
 
E2- 9 
Media Outlet 
Cutter Module
2.3.1  Loading the Media 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 14. Loading with cutter 
When the optional Cutter Module is fitted, the media is 
automatically cut.  A disc cutter is available as option. 
Insert the leading edge of the media into the cutter until it comes out 
the Media Outlet of the Cutter Module. 
 
 
CAUTION!...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.3 Loading Supplies
 
 
 
E2-10
2.3.2  Loading the Ribbon  
 
 
 
 There are two types of media available for printing on: thermal 
transfer and direct thermal (which has a chemically treated 
surface).  DO NOT LOAD a ribbon when using direct thermal 
media. 
 
1. Grasp the tabs on the top and bottom of the Ribbon Stoppers 
and move the Ribbon Stoppers back to the end of the Ribbon 
Shaft. 
 
 
 
 
 
 
 
 
 
 
 
 
 
2. Leaving plenty of slack between the...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.3 Loading Supplies
 
 
 
E2-11
 
2.3.2  Loading the Ribbon 
(Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3. Push Ribbon along the Ribbon Shafts to a position where the 
ribbon is fully to the Left against the stoppers when fitted.  
4. Lower the Print Head Block and set the Ribbon Shaft Holder 
Plate aligning its holes with the Ribbon Shafts. 
 
5. Take up any slack in the ribbon. Wind the leading tape onto the 
ribbon take-up roll until the ink...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.4 Connecting the Cables to Your Printer
 
 
E2-12
2.4 Connecting the 
Cables to Your 
Printer 
 
 The following paragraphs outline how to connect the cables from 
the printer to your host computer, and will also show how to 
make cable connections to other devices.  Depending on the 
application software you use to print labels, there are 5 ways to 
connect the printer to your host computer.  These are: 
•  An Ethernet connection using the printer’s standard...

2. PRINTER SETUP ENGLISH VERSION EO1-33094 
2.5 Turning the Printer ON/OFF
 
 
E2-13
2.5  Turning the Printer 
ON/OFF
 
 
 
2.5.1  Turning ON the Printer 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.5.2  Turning OFF the Printer 
 
 
 
 
 
 
 When the printer is connected to your host computer it is good 
practice to turn the printer ON before turning on your host 
computer and turn OFF your host computer before turning off the 
printer. 
 
 
1.  To turn ON the printer power, press the Power Switch as...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-14 
  2.6 Printer Setting 
 
 
 
  
Depending on the settings of your host computer or the interface 
being used it may be necessary to change the printer parameter 
settings. 
 
Follow the procedures described below to change the printer 
parameter settings to correspond to your environment.  
 
 
 
 
 
 
 
 
 
 
 
NOTE:
Incorrect settings can cause the printer not to function correctly.  If 
you have any problems with the parameter...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-15 
2.6 Printer Setting 
 (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.6.1  User System Mode  
 
„ Key functions in system mode 
Key Function 
[MODE]  Returns to the system mode menu. 
[CANCEL] or 
[FEED]+[RESTAR] Returns to the previous menu. 
Displays the next screen. [ENTER] or 
[PAUSE] 
Saves the settings and returns to the 
previous menu. 
Moves the cursor up. (Note 1) [UP] or [RESTART] 
Increases a value. (Note 2) 
Moves the cursor...

2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-16 
2.6.2 Parameter Setting 
 
 The Parameter Set menu allows the printer parameter settings to 
be modified. 
The following table shows the contents of the Parameter Set 
menu. 
 
Contents of the Parameter Set Menu  
Menu Sub menu  Parameter 
Printer Set  MEDIA LOAD Parameter 
set 
(Section 2.6.2.1)  FORWARD WAIT 
   FW/BK ACT 
   HU CUT/RWD 
   RBN SAVE 
    PRE PEEL OFF 
   BACK SPEED 
 Software Set FONT CODE 
    TYPE OF RIBBON...