Home > Toshiba > Printer > Toshiba B Ex4 User Guide

Toshiba B Ex4 User Guide

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba B Ex4 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 124
    Add page 41 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-27 
2.6.7  Dump Mode Setting 
 
 
 
 
 
 
 
  In the Dump Mode, data in the receive buffer are printed.  Data are 
expressed in hexadecimal values.  Th
is operation allows verification of 
the programming commands or debug of the program.  
(1) BUFFER 
This parameter is to choose the receive buffer to dump.  
  • RS-232C  RS-232C receive buffer 
•  CENTRONICS  Centronics receive buffer 
•  LAN  Network I/F receive buffer 
•  BASIC1  BASIC Interpreter:   
 I/F  → Interpreter buffer 
•  BASIC2 BASIC Interpreter: 
   Interpreter buffer  → I/F 
•  USB  USB receive buffer 
• RFID  RFID receive buffer 
 
 
(2) DUMP LIST 
  This parameter is to choose the output destination. 
 
• USB MEMORY  Saves in the USB memory.  → c  
•  PRINT Prints out  → d  
 
c  When USB MEMORY is selected: 
  A file is automatically created in the USB memory and named in the  following format based on the printer model and saved date. 
 /ATA0/DUMP/B-EX4T1_DUMP_1007291030.BIN 
  (e.g. B-EX4T Type1, 10:30, July 29, 2010) 
 
d   When PRINT is selected: 
  Choose a printing method.  • ON DEMAND  Prints 166 lines of data (approx. 50 cm), then 
stops.  Subsequent data is printed when the 
[ENTER] key is pressed. 
• ALL  Prints all data in the receive buffer. 
 
 
USER SYSTEM MODE   
BASIC 
Z-MODE 
AUTO CALIB 
DUMP MODE 
NOTE:  
If a file with the same name 
already exists in the USB 
memory, it will be overwritten.
    Add page 42 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-28 
2.6.7  Dump Mode Setting 
 (Cont.) 
 
 The data in the receive buffer is printed as follows.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Receive Buffer Size 
Interface  203 dpi  305 dpi 
RS-232C  6MB (393216 lines)  6MB (393216 lines) 
Centronics  6MB (393216 lines)  6MB (393216 lines) 
LAN  6MB (393216 lines)  6MB (393216 lines) 
BASIC 1  8KB (512 lines)  8KB (512 lines) 
BASIC 2  8KB (512 lines)  8KB (512 lines) 
USB  6MB (393216 lines)  6MB (393216 lines) 
RFID  8KB (512 lines)  8KB (512 lines) 
 
Required Media Length 
Interface  203 dpi  305 dpi 
RS-232C  1189.2 m  1189.2 m 
Centronics  1189.2 m  1189.2 m 
LAN  1189.2 m  1189.2 m 
BASIC 1  2 m  2 m 
BASIC 2  2 m  2 m 
USB  1189.2 m  1189.2 m 
RFID  2 m  2 m 
  *: Media length required for printing all data in the receive buffer. 
 
:
: 
: 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 7B 41 58 3B 2B 30 30 30 2C 2B 30 30 30 2C 2B 30  {AX;+000,+000,+0 
 30 7C 7D 7B 44 30 37 37 30 2C 31 31 30 30 2C 30  0|}{D0760,1100,0 
 37 34 30 7C 7D 7B 43 7C 7D 7B 4C 43 3B 30 30 33  740|}{C|}{LC;003 
 30 2C 30 30 32 30 2C 30 30 33 30 2C 30 36 36 30  0,0020,0030,0660 
 2C 30 2C 32 7C 7D 7B 4C 43 3B 30 30 37 30 2C 30   0,2|}{LC;0070,0 
 30 32 30 2C 30 30 37 30 2C 30 36 36 30 2C 30 2C   020,0070,0660,0, 
 39 7C 7D 7B 4C 43 3B 30 30 35 30 2C 30 30 32 30  9|}{LC;0050,0020  : 
: 
: 
 44 45 46 47 48 49 4A 7C 7D 7B 50 43 31 30 3B 30   DEFGHIJ|}{PC10;0 
 33 35 30 2C 30 34 30 30 2C 31 2C 31 2C 4B 2C 30   350,0400,1,1,K,0 
 30 2C 42 3D 41 42 43 44 65 66 67 68 69 6A 6B 6C   0,B=ABCDefghijkl 
 
 6D 6E 6F 70 7C 7D 7B 50 56 30 32 3B 30 33 33 30  mnop|}{PV02;0330 
 2C 30 36 36 30 2C 30 32 37 30 2C 30 32 35 30 2C   0660,0270,0250, 
 41 2C 30 30 2C 42 3D 42 7C 7D 7B 50 56 30 33 3B  A,00,B=B|}{PV03;  : 
: 
: 
 3B 30 39 30 30 2C 30 31 38 30 2C 54 2C 48 2C 30   ;0900,0180,T,H,0 
 35 2C 41 2C 30 3D 31 32 33 34 35 36 37 38 39 30  5,A,0=1234567890 
 41 42 43 44 45 7C 7D  00 00 00 00 00 00 00 00 00  ABCDE|}......... 
: 
: 
:
 
Print Conditions 
• Printing width: 3.9 inches 
(Approx. 100 mm) 
• Sensor selection: None 
• Print speed: 6”/sec. (203 dpi) 
  5”/sec. (305 dpi) 
• Printing mode: Depends on the 
selection in use. 
• 16 bytes/line 
• Data is printed in the order from
the new one to the old one. 
• Data specified by the receive 
buffer write pointer will be 
printed in boldface. 
NOTE: 
If an error occurs while printing, 
the printer stops printing and 
shows an error message. 
After clearing the error, the 
printer does not resume printing 
automatically.
    Add page 43 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-29 
2.6.8 Logging 
 
 
 
 
 
 The Log menu allows saving print logs in a USB memory. 
 
(1) LOG 
 
•  PRINTER TO USB  Saves print logs in the USB memory. 
 
  A file is automatically created in the USB memory and named in the following format based on the printer model and saved date. 
 /ATA0/LOG/B-EX4T1_LOG_1007291030.TXT 
  (e.g. B-EX4T Type1, 10:30, July 29, 2010)  
 
 
 
 
USER SYSTEM MODE   
Z-MODE 
AUTO CALIB 
DUMP MODE 
LOG 
NOTE:  
If a file with the same name 
already exists in the USB 
memory, it will be overwritten.
    Add page 44 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-30 
2.6.9 System Mode 
 
 
 
 
 
 
 
 
 
 
 
 
How to enter the System Mode 
 
 
 
 
 
 
The System Mode consists of the following menus.  
DIAG. 
Used to check and print the printer system information and 
maintenance counter status. 
PARAMETER SET ( ⇒ Section 2.6.2 ) 
Used to set the parameters for each printer function. 
ADJUST SET ( ⇒ Section 2.9 ) 
Used to fine adjust the print position, cut position, print tone, etc.  \
TEST PRINT ( ⇒ Section 2.8 ) 
Used to perform print tests.   
SENSOR ADJUST  
Used to check the sensor statuses and set each sensor. 
RAM CLEAR  
Used to perform a RAM clear.  DO NOT USE this menu. 
INTERFACE ( ⇒ Section 2.6.10 ) 
Used to set the interface parameters. 
BASIC (⇒ Section 2.6.4 ) 
Used to set the function of basic program when it is loaded to the 
printer. 
FOR FACTORY  
Used for an in-process inspection.  DO NOT USE this menu. 
RFID  
Used to set RFID related parameters. 
RTC (⇒ Section 2.6.11 ) 
Used to set the date and time of the real time clock, enable or disable 
the low battery check, and choose a real time renewal timing. 
Z-MODE ( ⇒ Section 2.6.5 ) 
Same as BASIC 
USB MEMORY ( ⇒ Section 2.6.12 ) 
Used to copy data to/from USB memory.  
RESET 
Used to reset the printer. 
 
 
Power OFFSystem Mode
Power ON while holding down 
[FEED]&[PAUSE]  
Power ON while holding down 
[MODE]
    Add page 45 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-31 
2.6.10 Interface Setting 
 
  The Interface menu allows configuring printer interface parameters.  
The following table shows the contents of the Interface menu. 
 
Contents of the Interface Menu  
Menu Sub menu  Parameter 
NETWORK LAN/WLAN Interface   SNMP 
   SETTING 
   BASIC INFORMATION 
   IP ADDRESS 
   GATEWAY ADDRESS 
   SUBNET MASK 
   SOCKET PORT 
   PORT NUMBER 
   DHCP 
    DHCP CLIENT ID 
    DHCP HOST NAME 
   WLAN STANDARD 
   WLAN MODE 
   DEFAULT KEY 
   802.11B CHANNEL 
   802.11B BAUD 
   802.11G CHANNEL 
   802.11G BAUD 
    WLAN POWER SAVE 
   WINS 
   WINS ADDRESS 
   LPR 
 USB   
 RS-232C SPEED 
   DATA LENGTH 
   STOP BIT 
   PARITY 
   CONTROL 
 CENTRO. ACK/BUSY 
   INPU PRIME 
    PLUG & PLAY 
 
SYSTEM MODE   
TEST PRINT 
SENSOR ADJUST 
RAM CLEAR 
INTERFACE
    Add page 46 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-32 
2.6.10 Interface Setting  (Cont.) 
 
 
2.6.10.1  Network Setting 
 
(1) LAN/WLAN 
 • OFF  LAN and Wireless LAN are disabled.  
•  ON (AUTO)  Automatically selected. 
•  ON (LAN)  LAN is enabled. 
•  ON (WLAN)  Wireless LAN is enabled. 
 
 
(2) SNMP 
 
• OFF  SNMP is disabled. 
•  ON  SNMP is enabled. 
 
 
(3) BASIC INFORMATION 
The following information is displayed.  
 
IP Address 
Gateway address 
Subnet mask 
Socket port status 
Socket port number 
 
 
(4) IP ADDRESS   
 
 
 
 
(5) GATEWAY ADDRESS 
 
 
 
 
(6) SUBNET MASK 
 
 
 
 
(7) SOCKET PORT 
 
• OFF  Socket port is disabled. 
•  ON  Socket port is enabled. 
 
 
 
 
 
 
 
 
192 020 168 010 
192 020 168 010 
255 255 255 000
    Add page 47 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-33 
2.6.10 Interface Setting  (Cont.) 
 
  (8) PORT NUMBER 
 
 
 
 
 
 
 
 
 
 
(9) DHCP 
 
• OFF  DHCP is disabled. 
•  ON  DHCP is enabled. 
 
 
(10) DHCP CLIENT ID 
 
• ASCII  DHCP client ID is entered with ASCII code.  → c  
•  HEX  DHCP client ID is entered with Hex. code.  → d  
  c  When ASCII is selected: 
  Enter 64 characters with ASCII code. 
  d  When HEX is selected: 
  Enter 64 characters with Hex. code. 
 
 
(11) DHCP HOST NAME   
Enter 32 characters with ASCII code. 
 
 
(12) WLAN STANDARD   
•  11b/g 
•  11b 
•  11g 
 
65535
00000
65534
00001
    Add page 48 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-34 
2.6.10 Interface Setting  (Cont.)
 
 
  (13) WLAN MODE 
This parameter is to choose the connection mode and authentication.  
 
ADHOC OPEN     OFF 
        WEP40 
        WEP104 
  SHAREDNot used   WEP40 
        WEP104 
INFRA OPEN     OFF 
        WEP40 
        WEP104 
  SHARED    WEP40 
        WEP104 
  802.1x OPEN TLS WEP40 
        WEP104 
      TTLS WEP40 
        WEP104 
      LEAP WEP40 
        WEP104 
      PEAP WEP40 
        WEP104 
      MD5 WEP40 
        WEP104 
      EAP-FAST WEP40 
        WEP104 
    SHARED KEY EAP-MD5 WEP40 
        WEP104 
    NETWORK EAP WEP40 
        WEP104 
  WPA OPEN TLS   
      TTLS   
      LEAP   
      PEAP   
      EAP-FAST   
    NETWORK EAP   
  WPA-PSK      
  WPA2 OPEN TLS   
      TTLS   
      LEAP   
      PEAP   
      EAP-FAST   
    NETWORK EAP   
  WPA2-PSK
    Add page 49 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-35 
2.6.10 Interface Setting  (Cont.)
 
 
 
 
  (14) DEFAULT KEY 
This parameter is to choose a WEP key.  
 
 
 
 
 
 
 
(15) 802.11b CHANNEL  This parameter is to choose a channel for 802.11b WLAN.  
 
 
 
 
 
 
 
(16) 802.11b BAUD  This parameter is to choose a baud rate for 802.11b WLAN.  
 
• 11M 
•  5.5M 
•  2M 
•  1M 
 
 
(17) 802.11g CHANNEL  This parameter is to choose a channel for 802.11g. WLAN.  
 
 
 
 
 
 
 
(18) 802.11g BAUD  This parameter is to choose a baud rate for 802.11g  WLAN.  
 
• 54M 
•  48M 
•  36M 
•  24M 
•  18M 
•  12M 
•  9M 
•  6M 
•  11M 
•  5.5M 
•  2M 
•  1M 
 
4 
1 
14 
1 
14 
1
    Add page 50 to Favourites
    image text
    Enable zoom 
    							
2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-36 
2.6.10 Interface Setting  (Cont.) 
 
 
 
 
 
 
  (19) WLAN POWER SAVE 
This parameter is to choose whether to enable the power save function 
while WLAN communication.  
 
• OFF  Power save function is disabled.  
•  ON   Power save function is enabled. 
 
 
(20) WINS 
 
• OFF  WINS is disabled. 
•  ON (MANUAL)  WINS is enabled. (Manual) 
•  ON (DHCP)  WINS is enabled. (DHCP) 
 
 
(21) WINS ADDRESS 
The WINS address is displayed.  
 
 
(22) LPR 
 
• OFF  LPR is disabled.  
•  ON   LPR is enabled. 
 
 
 
 
2.6.10.2  USB 
 
(1) USB SERIAL ID   
•  OFF  USB serial ID is disabled.  
•  ON   USB serial ID is enabled. 
   
 
 
2.6.10.3  RS-232C 
 
(1) SPEED   
•  2400 bps 
•  4800 bps 
•  9600 bps 
•  19200 bps 
•  38400 bps 
•  115200 bps
    All Toshiba manuals Comments (0)

    Related Manuals for Toshiba B Ex4 User Guide