Tone Commander 524 Installation Instructions

Pickup Code Sequence
Dial Pad Key Available Values
0first
(before station #)
1last
(after station #)
Table 8
Dialing Speed
Dial Pad Key Available Values
6slow
(6 digits/sec)
0fast
(10 digits/sec)
Table 9
Pause Time
Dial Pad Key Available Values
2 200 ms
3 300 ms
4 400 ms
5 500 ms
6 600 ms
7 700 ms
8 800 ms
9 900 ms
Table 10
13-102408 Rev. HPage 31
Tone Commander 524 Installation Instructions
DSS key to select feature:C
Default value:first
This parameter determines when the console inserts the
Directed...

Hookflash Time
Dial Pad Key Available Values
5 500 ms
6 600 ms
7 700 ms
8 800 ms
9 900 ms
0 1 sec
Table 11
Dial Tone Detect Time
Dial Pad Key Available Values
1 500 ms
2 600 ms
3 700 ms
4 1 sec
5 1.2 sec
6 1.5 sec
7 1.8 sec
8 2 sec
Table 12
Page 3213-102408 Rev. H
Tone Commander 524 Installation Instructions
DSS key to select feature:F
Default value:600 ms
This parameter sets the length of a timed hookflash generated
during call transfer and autodial operations. The default value is
adequate for most...

Hold Recall Time
Dial Pad Key Available Values
3 30 sec
4 40 sec
5 50 sec
6 60 sec
9 90 sec
1 2 min
2 3 min
0 no recall
Table 13
Hold Release Time
Dial Pad Key Available Values
140ms
280ms
3 200 ms
4 400 ms
5 600 ms
6 800 ms
7 1 sec
8 2 sec
Table 14
13-102408 Rev. HPage 33
Tone Commander 524 Installation Instructions
DSS key to select feature:H
Default value:90 sec
Calls on console hold longer than the Hold Recall Time will
recall the console.
Set this parameter according to customer preference.
NOTE–...

Queue Priority
Dial Pad Key Available Values
1 stations only
2 stations, then lines
3 lines, then stations
4 FIFO
Table 15
Alert Type
Dial Pad Key Available Values
1 normal ringing
2 distinctive ringing
0 both
Table 16
Ringing Type
Dial Pad Key Available Values
1 long
0 short
Table 17
Page 3413-102408 Rev. H
Tone Commander 524 Installation Instructions
DSS key to select feature:K(per console)
Default value:FIFO
Calls are queued for attendant processing in the order received.
The first call in queue is...

Special Feature Key Assignment
Spare line keys may be programmed to activate special features. Such usage precludes the connection of
lines to these positions. Be sure to identify the keys with the supplied key cap labels.

Press HOLD, then TRANSFER, then RELEASE, thenC(2) on the dial pad to enter configuration
programming mode.
CONFIGURE PROG will be displayed.

Press the DSS key to select the feature to be programmed:
R– Page key

Press dial pad key
*to display the key that is set to activate the...

Programming Features Selectable Per Line
The following programmable features do not apply to line keys that have been programmed for Page.

Press HOLD, then TRANSFER, then RELEASE, thenC(2) on the dial pad to enter configuration
programming mode.
CONFIGURE PROG will be displayed.

Press a DSS key to select the feature to be programmed.
The display will show the item name.
The station status lamp will light steadily.

Press the line key to be programmed with the selected feature.
The display will show the...

Music On Hold
DSS key to select feature:Q
Default Value for each line:on
This selects whether the external music source will be connected to a line that is on hold at the console
(hard hold, not
Centrex hold).
13-102408 Rev. HPage 37
Tone Commander 524 Installation Instructions 

DSS/Autodial Number Programming
Each DSS key may be programmed to autodial up to 24 digits or functions, including 0-9,*, #, dial tone
detect, a hookflash (transfer signal), and a pause. The PICK UP key autodials the call pickup code; it must
be also programmed with the required digits.
Digits are entered with the dial pad. The VOL keys and DSS key #5 are used to enter the pause, flash, and
dial tone detect functions – these functions are printed below the keys on the console front panel.
DIAL TONE...

For example, to program a DSS key to dial a hookflash, wait for dial tone, then dial station5314:
Pick Up Key Programming
The PICK UP key programming procedure is similar to that for DSS keys. Press PICK UP instead of
selecting a DSS key, then proceed as illustrated below. Consult the telco for the required pickup code.
IMPORTANT– A DIAL TONE detect must be entered before the Directed Call Pickup code to ensure that
steady dial tone is received before dialing begins. This may not apply to the few...

Name Display Programming
Any DSS/Autodial key to be programmed with a name display must already be programmed for autodialing;
autodial programming may be changed without reprogramming the DSS name display. This restriction does
not apply to line keys, since they cannot be programmed for autodialing.
Set the Name Program Lock Switch (switch #3) inside the CPU toOFF(unlocked) before proceeding – see
page 23.

Press HOLD, then TRANSFER, then RELEASE, thenN(6) on the dial pad to enter name
programming...