Tone Commander 1030/1560 Installation Instructions

Wall
Jack
PinoutWall Jack
Typical
Wire ColorConsole #1
Designation
(connector 1)Console #2
Designation
(connector 1)Typical 3 Pair
Console Cable
Wire Color(actual
wire color)
1 WHT 1C+ (YEL-BRN) 2C+ (VIO-GRN) WHT-GRN
2 BLK 1C+ (YEL-GRN) 2C+ (VIO-ORN) WHT-ORN
3 RED 1C- (ORN-YEL) 2C- (BLU-VIO) BLU-WHT
4 GRN 1C+ (YEL-ORN) 2C+ (VIO-BLU) WHT-BLU
5 YEL 1C- (GRN-YEL) 2C- (ORN-VIO) ORN-WHT
6 BLU 1C- (BRN-YEL) 2C- (GRN-VIO) GRN-WHT
Table 5 –Console “Power” Jack Pinout
The total console cable length, including...

Console Installation
Preliminary Testing
At this time, you should have completed the following:


Mounted the CPU and blocks


Installed the cables from the CPU to the blocks


Connected Tip and Ring from each line to the block


Connected Tip and Ring from each monitored station to the block


Installed the console cables and jacks


Assembled and connected the console(s)
It is a good idea to briefly test the operation of the 1030/1560 before proceeding with installation or
programming.
1. Plug the CPU...

B. The console should emit two triple beeps, then briefly display 1030 OK or 1560 OK.
If these indications are not observed, check both voice/data and power cabling.
2. Repeat step 1 at attendant position #2, if the system is so equipped.
C.O. Line Testing
Perform the following tests on each telco/PABX line. Repeat at attendant position #2, if the system is so
equipped.
Line Access and Imbalance Testing
1. Press the key representing the line to be tested.
The associated line lamp (telephone symbol)...

Ring Trip and Imbalance Testing
1. Dial the number of the line to be tested from another station.
The associated line lamp will flash slowly.
or
The associated line lamp will flash quickly, if the line has been optioned for ring delay.
2. Press the line key to answer the call.
The line lamp changes from flashing to flickering.
3. Listen for audible hum or excessive noise.
PA S S– Such noise or hum is not present.
FAILURE– Such noise or hum is present.
IMPORTANT– Upon detection of audible hum or excessive...

CPU Option Switches
Switches on the CPU control system programming and Night Service options. The switches are ON when
set towards the right side of the CPU. When a programming option is locked, programming changes are
not allowed. The switch location is shown in the figure below and on page 16.
SWITCH FUNCTION
1OFF – Autodial Program unlocked
ON – Autodial Program locked
2OFF – Configuration Program unlocked
ON – Configuration Program locked
3OFF – Name Program unlocked
ON – Name Program locked
4OFF –...

Optional Equipment Installation
The following options require system programming for proper operation. Refer to the Configuration
Programmingsection.
Night Service
The console may either switch the telephone system to night transfer, or ring a night bell during incoming
ringing when the attendant selects Night Service mode. Only one of these options may be installed.
Option switch #4 on the CPU selects the Night Service mode. Set this switchOFFfor night transfer, orON
for night ringing.
Night Ringing...

Night Transfer
The night transfer leads from the telephone system remain connected together when the console is in Night
Service mode, and during a power interruption at the CPU.
Music On Hold
An external music source is required for Music On Hold. It will be assigned to the lines during configuration
programming. The music input may be connected to any type of compatible music source (refer to the
Specifications
section).
The music source can be connected to the jack provided on the CPU, or punched down...

Block Connections
Paging
Tone Commanders PA-24 Paging/Chime module interfaces the 1030/1560 console to a paging system.
The module includes a night ringing chime and switching for background music control. Power is derived
from the 1030/1560 CPU.
Paging can be connected to any spare line key on the 1030/1560. Refer to the PA-24 Paging/Chime
Module Installation Instructions, doc. #13-102595.
Page 2813-102360 Rev. H
Tone Commander 1030/1560 Installation Instructions
1. Connect a twisted wire pair...

Configuration Programming
Various network interface and operation parameters are programmable by the installer, allowing
compatibility with a wide variety of central offices and PABXs. The system is pre-programmed at the
factory; many installations will require few changes to these values. Programming is retained in the CPUs
memory when power is disconnected.
Systems with two attendant positions require programming at both consoles for recall rings and line privacy.
The programming procedures for ring...

Using Configuration Programming Mode
The configuration programming mode must be entered prior to attempting any of the following
programming procedures.Enter this mode only when the console is idle, i.e., no calls are in progress or on
hold and the time of day is displayed.
The Configuration Program Lock Switch (switch #2) inside the CPU must beOFF(unlocked) before
proceeding (see page 25).
Toenterconfiguration programming mode:

Press HOLD.

Press TRANSFER.

Press RELEASE.

Press dial pad keyC(2).
The...