Tone Commander 1030/1560 Installation Instructions

Installation
Contents of Shipping Boxes
The Tone Commander 1030/1560 system is shipped in two boxes: one for the console, and one for the
central processing unit (CPU). Please compare the contents of these boxes with the lists below. Contact
your distributor if any items are missing or damaged.
Console Box:
(1) console
(2) 7´ line cords
(1) handset with cord
(1) handset cradle
(2) cradle mounting screws
(1) Attendant’s Guide
(1) Quick Reference Card
(1) bag of clear keycaps (1030: 41, 1560: 46)
(2)...

CPU Installation
Mounting CPU and Blocks
Refer to Figure 5 on page 16.
1. Fasten a plywood sheet to the wall with hardware suitable for the wall material.
2. Using the supplied mounting template, mark and pre-drill the mounting holes for the CPU.
Make sure that the CPU mounting location is within 5 feet of a standard grounded power outlet.
Allow at least one foot of free space above and below the CPU for ventilation.
3. Drive in four suitable fasteners (such as #10×¾ pan head tapping screws), leaving the...

Cabling to Blocks
Refer to Figure 5 on page 16.
1. Punch down the cables to the blocks as shown in the Wire Color columns of Tables 1, 2, and 3. The
cable with the male connector should be punched down to the right side of block #1.
2. Plug the 25 pair cable from block #1 into the connector on the left side of the main CPU circuit board.
3. Plug the cable from the left side of block #2 into the connector on the lower right side of the main CPU
circuit board.
4. Plug the cable from the right side of block...

CPU Chassis Grounding
This ground connection is required for safety and EMI shielding. It is usually provided by the 3rd wire on
the CPU power cord. If the integrity of the power outlet ground is questionable, use the ground connection
shown below for the 1030/1560 CPU.
1. Connect a solid copper #10 or #12 AWG wire to the ground terminal on the CPU. The wire should be
tightly clamped between the ground screw and the cup washer.
2. Connect the wire to an approved ground, such as MGN (multi-grounded...

Line Testing
Connect a test telephone to each line; verify the presence of dial tone, and break dial tone by dialing a
number.
The 1030 and 1560 allow DTMF tone dialing only – refer to the Telco/PABX Requirements
section.
Test any additional features ordered with the lines. Open circuit voltage must be approximately 48 volts.
Station Connections
Station Monitoring
13-102360 Rev. HPage 15
Tone Commander 1030/1560 Installation Instructions
Figure 4
ConnectT(Tip) andR(Ring) from each
monitored station to...

Page 1613-102360 Rev. H
Tone Commander 1030/1560 Installation Instructions
Figure 5– 1030/1560 Typical Installation 

CONNECTOR #1
PIN NO.
WIRE COLOR(left side of block unused)DESIGNATION(right)
26·······WHT-BLU······· – ··········1TN
1·······BLU-WHT······· – ··········1RN
27·······WHT-ORN······· – ··········1C1
2·······ORN-WHT······· – ··········1C2
28·······WHT-GRN······· – ··········1C3
3·······GRN-WHT······· – ··········1C4
29·······WHT-BRN······· – ··········2TN
4·······BRN-WHT······· – ··········2RN
30·······WHT-SLT ······· – ··········2C1
5·······SLT-WHT ······· – ··········2C2
31·······RED-BLU······· –...

CONNECTOR #2 CONNECTOR #3
PIN NO.
WIRE COLORDESIGNATION(left)DESIGNATION(right)
26·······WHT-BLU·······T1···········T16
1·······BLU-WHT·······R1···········R16
27·······WHT-ORN·······T2···········T17
2·······ORN-WHT·······R2···········R17
28·······WHT-GRN·······T3···········T18
3·······GRN-WHT·······R3···········R18
29·······WHT-BRN·······T4···········T19
4·······BRN-WHT·······R4···········R19
30·······WHT-SLT ·······T5···········T20
5·······SLT-WHT ·······R5···········R20...

CONNECTOR # 4CONNECTOR #5
PIN NO.WIRE COLORDESIGNATION(left)DESIGNATION(right)
26·······WHT-BLU·······T31 ··········T46
1·······BLU-WHT·······R31 ··········R46
27·······WHT-ORN·······T32 ··········T47
2·······ORN-WHT·······R32 ··········R47
28·······WHT-GRN·······T33 ··········T48
3·······GRN-WHT·······R33 ··········R48
29·······WHT-BRN·······T34 ··········T49
4·······BRN-WHT·······R34 ··········R49
30·······WHT-SLT ·······T35 ··········T50
5·······SLT-WHT ·······R35 ··········R50...

Console Cable Installation
Wall
Jack
PinoutWall Jack
Typical
Wire ColorConsole #1
Designation
(connector 1)Console #2
Designation
(connector 1)Typical 3 Pair
Console Cable
Wire Color(actual
wire color)
1 WHT 1C3 (WHT-GRN) 2C3 (RED-BLU) WHT-GRN
2 BLK 1C1 (WHT-ORN) 2C1 (WHT-SLT) WHT-ORN
3 RED 1RN (BLU-WHT) 2RN (BRN-WHT) BLU-WHT
4 GRN 1TN (WHT-BLU) 2TN (WHT-BRN) WHT-BLU
5 YEL 1C2 (ORN-WHT) 2C2 (SLT-WHT) ORN-WHT
6 BLU 1C4 (GRN-WHT) 2C4 (BLU-RED) GRN-WHT
Table 4 –Console “Voice/Data” Jack Pinout
Page...