Timex Dive Casual and Performance User Manual

           TABLE OF CONTENTS        2    How to Start Your Watch       3    Water and Shock Resistance
       4    Indiglo
®Night-Light
        5      Date Models
       7    Day/Date Models
       8    Easy Set Alarm      12      Perpetual Calendar
     15      Elapsed Time Ring
     17      Tachymeter Ring
     18      Compass Ring
     19      How to Adjust Bracelet
     21      Bracelet Link Removal
     22      Battery
     23      Warranty
ENGLISH
W217_EN_CEU_analoglayout_4  3/9/10  10:40 AM  Page...

WATER AND SHOCK RESISTANCEIf your watch is water-resistant, meter marking
(WR_M) is indicated.
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE,
DO NOT PRESS ANY BUTTONS OR PULL OUT 
THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-
RESISTANT.
3
ENGLISH
HOW TO START YOUR WATCHTo start your watch remove the plastic guard from
under the crown, then press the crown in against 
the case. The second hand will begin advancing in
one-second intervals.
Some deep-depth...

DATE MODELS
TO SET TIME:1)   PULL crown all theway out and turn to
correct time.
2)   Push crown in to restart. For screw-in
setting crown, push
crown in while turning
CLOCKWISE to tighten.
Watches with date: Note correct time of day 
(A.M or P.M.) for proper date function.
TO SET DAY: 1)   PULL crown to “middle” position and turn  CLOCKWISE until correct day appears. If day does
not change, pull crown to “out” position and turn
CLOCKWISE or COUNTERCLOCKWISE through 
necessary number of 24 hour periods...

DAY / DATE MODELS
TO SET THE TIME:1)   PULL the crown outto the “C” position.
2)   TURN the crown either way to the 
correct time.
3)   PUSH in the crown to the “A” position.
TO SET THE DATE: 1)   PULL the crown out to the “B” position. 
2)   TURN the crown either way to the correct date.
3)   PUSH in the crown to the “A” position.
TO SET THE DAY: 1)   PULL the crown out to the “C” position.
2)   TURN the crown either way for full 24 hour cycleto set day.
3)   PUSH the crown in to the “A” position.
7...

EASY SET ALARM DATE & TIME SETTINGS
TO SET THE DATE: 
1)   With the TIMEKEEPING CROWN in the “B” positionTURN the TIMEKEEPING CROWN or TURNING RING
in either direction to set the date. 
TO SET THE TIME:1)   With the TIMEKEEPING CROWN in the “C” positionTURN the TIMEKEEPING CROWN or TURNING RING
in either direction to set the time. 
EASY SET ALARM SETTINGS1)   Your easy set alarm watch is equipped with twotypes of alarms:
2)   12-Hour Alarm: rings OR vibrates twice per day at the desired hour and minute...

TO SET THE HOURLY ALARM:1)   With the ALARM CROWN in the “D” position, TURNthe ALARM CROWN or TURNING RING in either
direction to set the minute alarm marker. 
2)   To activate the alarm to ring or vibrate at the desired minute, PULL the ALARM CROWN out to
the “F” position. Three beeps sound and flash 
OR a vibration indicates the Hourly Alarm is
 activated. 
3)   The alarm will sound and the dial will flash OR vibrate at the desired minute and will repeat
every hour on the specified minute unless the...

TO SET TIMETo set time, simply pull crown all the way out and
turn. Day and date change automatically when time
is adjusted past midnight; there is no additional step
for setting day or date. Push crown in when done.
After setting, if date changes at noon, time needs to
be adjusted ahead or back 12 hours.
If crown is accidentally put in MIDDLE position and
turned, date display will change temporarily, but date
setting is unaffected. Simply pull crown all the way
out and set time. Proper date display will...

ELAPSED TIME RINGIf your watch is equipped with a rotatable outer ring
on the face, with numbers corresponding to minutes,
you can use this Elapsed Time Ring to time an activity
from the start, or to mark the ending time for the
duration of an activity.
TO TIME AN ACTIVITY FROM THE START:Set the Start/Stop triangle at the time (hour or
minute) when you start the activity (As shown on the
left in the illustration shown below). At completion,
you can see how long the activity took.
15
ENGLISH
postage and...

TACHYMETER RINGThe tachymeter feature can be used to measure
speed in miles per hour (MPH), nautical miles per
hour (knots) or kilometers per hour (KPH) using the
sweep second hand and the scale on the wall above
the watch face. You need to know the actual  distance
you are covering in miles or km.
Start the chronograph with the second hand at zero
(the twelve o’clock position). Within the first minute,
the second hand will point to the rate for a one-mile
(or one kilometer) course: if it takes 45...

HOW TO ADJUST BRACELET(Variations of the following bracelet sections apply to
all watch models).
SLIDING CLASP BRACELET1    Open locking plate.
2.   Move clasp to desired bracelet length.
3.   Exert pressure while holding locking plate andslide clasp back and
forth until it engages
in grooves on under-
side of bracelet.
4.   Press locking plate down until it snaps
closed. Clasp can be
damaged if excessive
force is used.
19
ENGLISH
COMPASS RINGIf your watch is equipped
with a movable ring around
the dial...