Telrad Digital DIGITAL Family Of Systems Administration, Installation And Upgrade Addendum Manual

76-110-0175/G, Issue 2
3-14 3.6.2SMDR Screen [YC-IS-F9]
There is a new field in this screen:
DID report to SMDR
A new field has been added to designate whether or not DID num-
bers are printed out in SMDR reports, in the ACC field.
Legal values: Y (Yes), N (No).
Default: N.
3.6.3GENERAL PARAMETERS Screen [SP-PR]
There are two new fields in this screen:
ACD-IQ version
In this field you designate which version of ACD-IQ is connected to 
the system. If the version is 3.0 or higher, CID and DID numbers are...

4-1 Section 4
UPGRADE PROCEDURES4.1GENERAL
You can upgrade an existing DIGITAL system from:
•DIGITAL KEY BX Release SB3, SBU5, or SB6 to Release SB7;
•DIGITAL 400 Release DB3, DBU5, or DB6 to Release DB7;
•DIGITAL KEY BX to DIGITAL 400.
The upgrade procedures are identical to those for upgrading from 
Release 5 DIGITAL KEY BX AND DIGTAL 400 systems to Release6 
systems and are described in the Release 6 Upgrade Manual, Cata-
log No. 76-110-0455/F.
There is only one minor change, as described below in...

76-110-0175/G, Issue 2
4-2 4.3.2Recommended programming
It is recommended that for every loop-start or group-start analog cen-
tral office outside line, the LENGTH field be defined as: Long. This 
applies whether the outside line is connected to an MPD (DIGITAL 
KEY BX systems only), COL, CHL, or COG card. 
The LENGTH field appears on the following screens 
(path [YC-SC-F9]):
•MPD CARD UNITS DEFINITION Screen;
•COL CARD UNITS DEFINITION Screen;
•CHL CARD UNITS DEFINITION Screen;
•COG CARD UNITS...

A-1 Appendix A 
SUMMARY OF PROGRAMMING CHANGESA.1GENERAL
This appendix provides a summary of the new fields and new values 
used in programming the configuration file for the Release 7 
DIGITAL KEY BX, DIGITAL 400, and DIGITAL 1000 systems.A.2NEW PROGRAMMING FIELDS AND VALUES
Table A-1 provides a list of the new fields and new legal values in 
found the configuration programming the Release 7 DIGITAL sys-
tems. 
Table A-1 New fields and values on the programming screens 
PathFieldLegal valuesNotes
YC-SC...

76-110-0175/G, Issue 2
A-2YC-CP-UP 
(for N24 card)
-- see Section 
3.4.3 ProtocolDPNS, QSIG (default DPNS)
Layer 2 sidefor DPNSS: A (A-side), B (B-side)
for QSIG: M (master), S (slave)
Layer 3 sidefor DPNSS: X (X-side), Y (Y-side)
for QSIG: M (master), S (slave)
Signaling channelfor N24 card D-channel for signaling: 1 - 24
or N30 card D-channel for signaling: 1 - 31
Back-to-back 
connectionY (direct to peer), N (via CO)
YC-CP-EP 
(for N30 card) 
-- see Section 
3.4.3 Protocolfor N24 and N30 network...

Appendix A: SUMMARY OF PROGRAMMING CHANGES
A-3 SP-FN 
(see Section 
3.5.1)Call Account 
Monitor (FLNP 
code and Fea-
ture code)
Up to four digits including *, # CLIR - Caller ID 
Presentation 
(FLNP code and 
Feature code)
Drop from confer-
ence (FLNP code 
and Feature 
code)
Internet connec-
tion (FLNP code 
only)
Background 
Music 9- 12 (for 
DIGITAL 1000 
system only; 
FLNP code and 
Feature code)
Internal Page 9 - 
16 (for DIGITAL 
1000 system 
only; FLNP code 
and Feature 
code)
External Page 9 -...

76-110-0175/G, Issue 2
A-4SP-SD-SG 
(see Section 
3.5.2)Group nameAny 10 characters
SP-SD-NS 
(see Section 
3.5.3)Group 1 - 10 
nameA - Z (capital letters), 0 - 9,  _ (underscore), / (slash), space
PT-TF-F9 
GR-AG-F9
(see Section 
3.6.4 and 3.6.6)Disconnect 
supervisedY (The trunk sends a signal to the DIGITAL system when the 
    far end disconnects.), 
N (The trunk does NOT send a signal to the DIGITAL system 
    when the far end disconnects.)
GR-TF 
(see Section 
3.4.8)Max % for VC 
(virtual...

Appendix A: SUMMARY OF PROGRAMMING CHANGES
A-5 NT-FS 
(see Section 
3.4.4)3-party servicesY (feature supported), N (feature NOT supported)
Callback busyY (feature supported), N (feature NOT supported)
Callback no 
answerY (feature supported), N (feature NOT supported)
MessageY (feature supported), N (feature NOT supported)
IVM supportedV5U (ImaGEN version 5.00U), V7 (ImaGEN version 7.00)
NT-PR 
(see Section 
3.4.5)Feature setfor DIGITAL KEY BX: 1 - 16
for DIGITAL 400: 1 - 32
for DIGITAL 1000: 1 - 64...

76-110-0175/G, Issue 2
A-6THIS PAGE INTENTIONALLY LEFT BLANK 

INDEX
INDEX-1 Numerics
3-party services 3-9, A-4
A
account monitor A-3
ACD-IQ 2-4, A-3
adapter for DPNSS 2-11
addressing mode 3-9
administration 3-1–3-14, A-1 – A-5 
APPLync card 2-4, 3-3
Attendant definition screen 3-3, 3-4
Avanti 
APPLync card 2-4, 3-3
configuration options 2-4
DATALync card 2-4, 2-5, 3-3
option module installation, 2-5 – 2-7
programming telephone sets 3-2
telephone set stand 2-5
B
Background Music A-3
Back-to-back connection 3-8
baud rate 3-1
BGM A-3
C
callback busy A-5
callback no...