Telrad Digital DIGITAL Family Of Systems Administration, Installation And Upgrade Addendum Manual

							76-110-0175/G, Issue 2
3-14 3.6.2SMDR Screen [YC-IS-F9]
There is a new field in this screen:
DID report to SMDR
A new field has been added to designate whether or not DID num-
bers are printed out in SMDR reports, in the ACC field.
Legal values: Y (Yes), N (No).
Default: N.
3.6.3GENERAL PARAMETERS Screen [SP-PR]
There are two new fields in this screen:
ACD-IQ version
In this field you designate which version of ACD-IQ is connected to 
the system. If the version is 3.0 or higher, CID and DID numbers are 
sent to ACD-IQ.
Legal values: 0.0 - 15.15.
Default: 0.0
Send Directory Softkey
Designate whether you want the idle display of Avanti 3025 stations 
to show a Directory softkey or a Phone book icon. If you set this field 
to Y, a Directory softkey appears. If you set this field to N, a Phone 
book icon appears.
Legal values: Y (Yes), N (No).
Default: N.
3.6.4PRIVATE TRUNK FEATURES Screen [PT-TF-F9]
There is a new field in this screen:
Disconnect Supervised
If the trunk sends a signal to the DIGITAL system when the far end 
disconnects, enter a Y in this field. If the trunk does not send a signal 
when the far end disconnects enter N in this field.
When Y is programmed in this field, the system allows this trunk to 
connect to Meet Me Conference.
Legal values: Y (Yes), N (No).
Default: Y.
3.6.5DID ROUTING Screen [RD]
A new legal value has been added for each of the parameters Day 
Routing and Night Routing. You can now enter DISA in either of 
these fields.
3.6.6TRUNK LIST Screen [GR-AG-F9]
The new field in this screen is the same as in Section 3.6.4. 
						

							4-1 Section 4
UPGRADE PROCEDURES4.1GENERAL
You can upgrade an existing DIGITAL system from:
•DIGITAL KEY BX Release SB3, SBU5, or SB6 to Release SB7;
•DIGITAL 400 Release DB3, DBU5, or DB6 to Release DB7;
•DIGITAL KEY BX to DIGITAL 400.
The upgrade procedures are identical to those for upgrading from 
Release 5 DIGITAL KEY BX AND DIGTAL 400 systems to Release6 
systems and are described in the Release 6 Upgrade Manual, Cata-
log No. 76-110-0455/F.
There is only one minor change, as described below in Section 4.2.4.2DIGITAL KEY BX  CONFIGURATION FILE NAME CHANGE
When upgrading DIGITAL KEY BX Release SB3, SBU5, or SB6 sys-
tems to SB7, the original Release SB3, SBU5, or SB6 configuration 
file is changed after the conversion. 
The original file name with a .cfg extension, is changed to cfg.bak.4.3MANDATORY AND RECOMMENDED PROGRAMMING
4.3.1Mandatory programming
In the DIGITAL KEY BX Release SB7 and the DIGITAL 400 Release 
DB7 systems, it is mandatory that the parameter Disconnect 
Supervised be properly defined for every trunk in the system. This 
field is found on the following screens:
•TRUNK LISTS Screen (for trunk groups) -- path [GR-AG-F9];
•ADDITIONAL TRUNK FEATURES Screen  (for private trunks) -- 
path [PT-TF-F9].
The Disconnect Supervised field should be programmed as Y if the 
trunk sends a signal to the DIGITAL system when the far end discon-
nects. If the trunk does not send a signal enter N in this field. 
						

							76-110-0175/G, Issue 2
4-2 4.3.2Recommended programming
It is recommended that for every loop-start or group-start analog cen-
tral office outside line, the LENGTH field be defined as: Long. This 
applies whether the outside line is connected to an MPD (DIGITAL 
KEY BX systems only), COL, CHL, or COG card. 
The LENGTH field appears on the following screens 
(path [YC-SC-F9]):
•MPD CARD UNITS DEFINITION Screen;
•COL CARD UNITS DEFINITION Screen;
•CHL CARD UNITS DEFINITION Screen;
•COG CARD UNITS DEFINITION Screen.
From the CARD CONFIGURATION Screen: 
1.Place the cursor on the appropriate card (MPD, COL, CHL, or 
COG).
2.Press F9 to access the appropriate CARD UNITS DEFINITION 
Screen.
3.Move the cursor to the LENGTH field.
4.Type: L.
WARNING
Only in special cases where the voice quality of
the outside line has been successfully tested may
the LENGTH field be programmed as S (Short) or
V (Very long). 
						

							A-1 Appendix A 
SUMMARY OF PROGRAMMING CHANGESA.1GENERAL
This appendix provides a summary of the new fields and new values 
used in programming the configuration file for the Release 7 
DIGITAL KEY BX, DIGITAL 400, and DIGITAL 1000 systems.A.2NEW PROGRAMMING FIELDS AND VALUES
Table A-1 provides a list of the new fields and new legal values in 
found the configuration programming the Release 7 DIGITAL sys-
tems. 
Table A-1 New fields and values on the programming screens 
PathFieldLegal valuesNotes
YC-SC
(see Sections 
3.2.1 and 3.4.1)Card typeNew values: ULD, UHD, N24, N30
YC-SC-F9
(ULD or UHD 
cards) -- see 
Section 3.2.2DNUp to four digits including *, #
StationE30, D30, S30, B30, M30, ATT
PathS (Single Audio Path), D (Dual Audio Path)
Add on 1
DSS1 - DSS8 (Direct Station Select console), 
VRC (voice recognition card), TAPI (DATALync data card), 
PCAPP (APPLync data card) Add on 2
Add on 3
Add on 4
YC-SC-F9
(N24 or N30 
cards) -- see 
Section 3.4.2DNUp to four digits including *, #
Public DNUp to 20 digits including *, # 
						

							76-110-0175/G, Issue 2
A-2YC-CP-UP 
(for N24 card)
-- see Section 
3.4.3 ProtocolDPNS, QSIG (default DPNS)
Layer 2 sidefor DPNSS: A (A-side), B (B-side)
for QSIG: M (master), S (slave)
Layer 3 sidefor DPNSS: X (X-side), Y (Y-side)
for QSIG: M (master), S (slave)
Signaling channelfor N24 card D-channel for signaling: 1 - 24
or N30 card D-channel for signaling: 1 - 31
Back-to-back 
connectionY (direct to peer), N (via CO)
YC-CP-EP 
(for N30 card) 
-- see Section 
3.4.3 Protocolfor N24 and N30 network cards: DPNS, QSIG (default 
DPNS)
Layer 2 sidefor DPNSS: A (A-side), B (B-side)
for QSIG: M (master), S (slave)
Layer 3 sidefor DPNSS: X (X-side), Y (Y-side)
for QSIG: M (master), S (slave)
Signaling channelfor N24 card D-channel for signaling: 1 - 24
or N30 card D-channel for signaling: 1 - 31
Back-to-back 
connectionY (direct to peer), N (via CO)
YS-IS-F9
(with the cursor 
on SMDR, press 
F9) -- (see Sec-
tion 3.6.2)DID report to 
SMDRY (yes), N (no)
SP-TM 
(see Section 
3.6.1)ISDN timer 302
(for ISDN trunks)1 - 20 (seconds)
Waiting tone time-
out3 - 60 (seconds)
Time for waiting 
for next char.2 - 10 (seconds) Table A-1 New fields and values on the programming screens (continued)
PathFieldLegal valuesNotes 
						

							Appendix A: SUMMARY OF PROGRAMMING CHANGES
A-3 SP-FN 
(see Section 
3.5.1)Call Account 
Monitor (FLNP 
code and Fea-
ture code)
Up to four digits including *, # CLIR - Caller ID 
Presentation 
(FLNP code and 
Feature code)
Drop from confer-
ence (FLNP code 
and Feature 
code)
Internet connec-
tion (FLNP code 
only)
Background 
Music 9- 12 (for 
DIGITAL 1000 
system only; 
FLNP code and 
Feature code)
Internal Page 9 - 
16 (for DIGITAL 
1000 system 
only; FLNP code 
and Feature 
code)
External Page 9 - 
24 (for DIGITAL 
1000 system 
only; FLNP code 
and Feature 
code)
Phone book pri-
vate list (Feature 
code only)
Phone book lists 
1 - 10 (Feature 
code only)
SP-PR 
(see Section 
3.6.3)ACD-IQ version0.0 - 15.15
Send directory 
softkeyY (Directory softkey will appear on the telephone display), 
N (Phone book icon or softkey will appear on the telephone 
    display) Table A-1 New fields and values on the programming screens (continued)
PathFieldLegal valuesNotes 
						

							76-110-0175/G, Issue 2
A-4SP-SD-SG 
(see Section 
3.5.2)Group nameAny 10 characters
SP-SD-NS 
(see Section 
3.5.3)Group 1 - 10 
nameA - Z (capital letters), 0 - 9,  _ (underscore), / (slash), space
PT-TF-F9 
GR-AG-F9
(see Section 
3.6.4 and 3.6.6)Disconnect 
supervisedY (The trunk sends a signal to the DIGITAL system when the 
    far end disconnects.), 
N (The trunk does NOT send a signal to the DIGITAL system 
    when the far end disconnects.)
GR-TF 
(see Section 
3.4.8)Max % for VC 
(virtual channel)0 - 100 (0 = network support services disabled)
FE-AT
 (see Section 
3.2.5)Map TypeED (for Avanti 3025 and Avanti 3020), 
SM (for Avanti 3015D and Avanti 3015), 
BA (for Avanti 3000)
FE-PK 
(see Section 
3.2.6)Map TypeED (for Avanti 3025 and Avanti 3020), 
SM (for Avanti 3015D and Avanti 3015), 
BA (for Avanti 3000)
FE-PK-F9 
(see Sections 
3.2.7 and 3.5.4)Programmable 
keysNew values: 
   BM 9 - 12 (Background Music for DIGITAL 1000), 
   PB PRV (private Phone book), 
   PB 1 - 10 (Phone books 1 - 10), 
   SP 90 - 99 (private speed dial)
Other values: see the Administration manual, Release 6
AT-AD 
(see Section 
3.2.3) ST20 ATT MAP1 - 4 (for all systems)
5 -24 (for DIGITAL 1000 only)
ST30 ATT MAP1 - 4 (for all systems)
5 -24 (for DIGITAL 1000 only)
AT-PK 
(see Sections 
3.2.4 and 3.5.4)Programmable 
keysNew values: 
   PB PRV (private Phone book), 
   PB 1 - 10 (Phone books 1 - 10), 
   SP 90 - 99 (private speed dial)
Other values: see the Administration manual, Release 6
RD 
(see Section 
3.6.5)Day routingNew value: DISA
Night routingNew value: DISA
DS-DS 
(see Section 
3.3.1)MAP #1for DIGITAL KEY BX: 1, 5
for DIGITAL 400: 1, 5, 9
for DIGITAL 1000: 1, 5, 9, 13, 17, 21, 25, 29, 33, 37, 41, 45
DS-PK 
(see Section 
3.3.2)Programmable 
keysExtension DNs, SPxx (Speed Dial code), 
ARxx (Automatic Redial code), - (None). Table A-1 New fields and values on the programming screens (continued)
PathFieldLegal valuesNotes 
						

							Appendix A: SUMMARY OF PROGRAMMING CHANGES
A-5 NT-FS 
(see Section 
3.4.4)3-party servicesY (feature supported), N (feature NOT supported)
Callback busyY (feature supported), N (feature NOT supported)
Callback no 
answerY (feature supported), N (feature NOT supported)
MessageY (feature supported), N (feature NOT supported)
IVM supportedV5U (ImaGEN version 5.00U), V7 (ImaGEN version 7.00)
NT-PR 
(see Section 
3.4.5)Feature setfor DIGITAL KEY BX: 1 - 16
for DIGITAL 400: 1 - 32
for DIGITAL 1000: 1 - 64
NT-PR-F9 
(see Section 
3.4.6)Feature setfor DIGITAL KEY BX: 1 - 16
for DIGITAL 400: 1 - 32
for DIGITAL 1000: 1 - 64
NT-NP 
(see Section 
3.4.7)Longest network 
path1 - 31 Table A-1 New fields and values on the programming screens (continued)
PathFieldLegal valuesNotes 
						

							76-110-0175/G, Issue 2
A-6THIS PAGE INTENTIONALLY LEFT BLANK 
						

							INDEX
INDEX-1 Numerics
3-party services 3-9, A-4
A
account monitor A-3
ACD-IQ 2-4, A-3
adapter for DPNSS 2-11
addressing mode 3-9
administration 3-1–3-14, A-1 – A-5 
APPLync card 2-4, 3-3
Attendant definition screen 3-3, 3-4
Avanti 
APPLync card 2-4, 3-3
configuration options 2-4
DATALync card 2-4, 2-5, 3-3
option module installation, 2-5 – 2-7
programming telephone sets 3-2
telephone set stand 2-5
B
Background Music A-3
Back-to-back connection 3-8
baud rate 3-1
BGM A-3
C
callback busy A-5
callback no answer A-5
Caller ID Presentation A-3
Card configuration screen 3-2, 3-7
Card parameters screens 3-7
CCB 3-9
CCNA 3-9
CLIR A-3
coaxial cable, adapter for DPNSS 2-11
configuration 
Avanti telephone sets 2-4
file name 4-1
CRC4 3-9
CRC6 3-9
D
data cards 
description 2-4, 2-5
installing 2-8, 2-9
wiring connections 2-8DATALync card 2-4, 2-5, 3-3
day routing A-4
digital private network 2-11
Direct Station Select console
connecting 2-5, 2-9
map 3-6, A-4
DISA A-4
disconnect supervised A-4
documentation 1-2
DPNSS  
definition 2-11
installing in UK 2-11, 2-12
programming 3-7,A-2
drop from conference A-3
DSS console
connecting 2-5, 2-9
map 3-6, A-4
E
EHD card preparation 2-2
ELD card preparation 2-2
external page A-3
F
feature set 3-9, 3-10, A-4
Features Set screen 3-9
fields 3-2 – 3-14, A-1 – A-5
Function access codes screen 3-12
G
generic functional protocol 2-12
group name A-4
I
ImaGEN 3-10, A-5
internal page A-3
Internet connection A-3
ISDN timer 302  3-13, A-2
IVM 3-10, A-5
L
Layer 2 side 3-8
Layer 3 side 3-8
LEDs 2-2