Technics Keyboard Sx Kn7000 Owners Manual

Setting display
When you select an item from the menu display,
the setting display for the item is shown.
The buttons to the right, left and/or directly below
the display are used to select and adjust the set-
tings.
Example of setting display: MASTER
TUNING
Press the button corresponding to the 
∧ or ∨ but-
ton on the display to change the value.
•In this manual, this procedure is written as
follows: “Use the 
∧ and ∨ buttons to adjust
the pitch.”
TEMPO/PROGRAM 
If the TEMPO/PROGRAM indicator is lit...

HELP
You can find an explanation of each button’s
function on the display.
1.Press the HELP button.
•The following display appears.
2.Use the buttons below the display to select a
language.
3.Press the OK button.
4.Press a button on the panel whose explanation
you wish to read.
•An explanation of the button’s function is
shown on the display.
5.Press the HELP button again to exit the help
mode.
•Attention display messages and error mes-
sages are also shown in the selected lan-
guage.
•The appearance of...

•The PANIC function interrupts the sound, for
example, when it fails to cease during a MIDI
performance.
5.While pressing the SET button, specify where
you wish to paste (put) the item.
•While the SET button is depressed, the display
appears as shown below. Use the buttons to
the left and right of the display to specify where
you wish to paste the item.
6.Repeat steps 4 and 5 to create the display you
want.
•There are nine settable items on the display.
7.On the FAVORITES SETTINGS display, press
the OK...

Overview of sounds and effects
The following is an overview of the sound parts and the SOUND DSP (the basic effects) of this in-
strument.
NX SOUND
NX SOUND is the Technics original sound gen-
erator format which evokes realtime perform-
ance quality and expressive power, and
dramatically expands the number of sounds and
effects generated. This format includes GM2
(General MIDI Level 2), and make various con-
trols possible when data is created and repro-
duced by computer. 
 @BULLET = For information...

Selecting sounds
Select the sounds for the three parts you can play on the keyboard—RIGHT 1, RIGHT 2 and LEFT. After
first selecting a part and a SOUND GROUP, choose the desired sound from the display.
Select a sound
1.In the PART SELECT section, choose RIGHT
1, RIGHT 2 or LEFT.
•The CONDUCTOR buttons are used to specify
which part is heard. (Refer to page 39.)
•For the RIGHT 1 and RIGHT 2 parts, when a
CONDUCTOR button is selected, the corre-
sponding PART SELECT button is also acti-
vated.
2.In the...

3.Use the ∧ and ∨ buttons to select a GROUP
of sound.
4.Use the buttons on both side of the display to
select the sound.
•The numerical value that is displayed for each
sound is the MIDI [BANK MSB, LSB]-PRO-
GRAM CHANGE number.
•GM2 sounds are selected on this display.
ALPHABET
Press the CATEGORY button to show the sound
names in alphabetical order.
•Press the ALPHABET button to return to the
CATEGORY display.
Digital Drawbar
You can play organ sounds while controlling the drawbars on the display.
1.In...

Organ Tabs
You can play organ sounds for which the tab can be turned on or off on the display.
1.In the CONDUCTOR or PART SELECT sec-
tion, select the part.
2.Press the ORGAN TABS button to turn it on.
•The display looks similar to the following.
3.Use the balance buttons below the display to
turn on or off each tab.
•Note that the ORGAN TABS can not be
selected for the ACCOMP and BASS parts of
the COMPOSER or PERFORMANCE PADS.
Change the sound type and make each
type setting
You can select from three...

TREMOLO
Tremolo is a rapid oscillation in volume, like the
effect of a rotating speaker. The tremolo speed
can be changed while you are playing.
•The SOUND DSP (ROTARY SPEAKER/
ROCK ROTARY) is used for the tremolo effect.
This effect does not work if the SOUND DSP
button is turned off.
Use the TREMOLO button to switch between the
SLOW and FAST rotating speeds.
•The tremolo setting is effective for each part
in common.
•TREMOLO does not work for parts which can-
not use the SOUND DSP.
VIBRATO
Effective...

Assigning parts to
 the keyboard
The CONDUCTOR buttons are used to assign the parts (RIGHT 1, RIGHT 2, LEFT) to the keyboard in
many different ways. For example, you can split the keyboard into right and left sections (SPLIT), and
assign a different sound to each section.
CONDUCTOR
•The volume for each part can be adjusted independently. (Refer to page 29.)
•The following conditions are in effect when the AUTO PLAY CHORD is used.
—BASIC, FINGERED mode: You cannot assign sounds to all the keys.
—PIANIST...

SPLIT POINT
When the keyboard is divided into left and right
sections, the split point is indicated by the lit in-
dicator. You can change the location of the split
point.
•Each time the SPLIT POINT button is pressed,
the indication moves to the next split point in
the following order. G2 → C3 → G3 → cus-
tomized split point (all indicators off) (see
below).
Customized split point
Use the following procedure if you wish to store
a split point at a location other than G2, C3 or
G3.
1.Press and hold the...