Studio Experience Projector Premier 30hd User Manual

Easy to Use Functions
49
Deinterlace
This function allows you to determine the type of incoming video content-film, static interlaced video and 
moving interlaced video. Different algorithms are applied for each of the content types.
Select “Deinterlace” from the 
“Options” menu on the menu screen.
For operating the menu screen, see 
page 31.
 Note
•  In PAL50Hz or SECAM, the 2:2 pull down 
enhancement will be enabled only in film 
mode, after the film source has been 
entered.
Selected itemDescription...

50
Easy to Use Functions
Reset
Select this option to set all items in the “Option” 
menu to the factory default values.
Lamp Timer Reset
Lamp Timer Reset is used to reset the lamp 
counter.
You should reset the Timer after you install a 
new lamp. The cumulative lamp usage time is 
shown in the Status Screen.
Main Menu
Main Menu 

Easy to Use Functions
51
Status Screen
The Status screen displays information about the current input signal.
Factory reset
The Logo will be shown for about 20 seconds, 
then the projector will be reset. 
 Note
•  The Logo will be shown about 20 seconds, 
and then the projector will be reset.
Main Menu
Screen display during Factory Reset
Main Menu 

52
Easy to Use Functions
NOTES 

Appendix
53
Appendix 

54
Appendix
Maintenance
Cleaning the projector
„Unplug the power cord before cleaning the projector.
„Avoid using benzene or thinner, as these can damage the finish on the cabinet and operation panel.
„Do not use volatile agents such as insecticides on the projector.
„Do not leave rubber or plastic objects in contact with the projector for long periods as they may damage 
the finish of the projector.
„Wipe off dirt gently with a soft flannel cloth.
„For hard-to-remove dirt, soak a cloth in a neutral...

Appendix
55
Cleaning the Ventilative Holes
•  This projector is equipped with ventilative 
holes to ensure the optimal operating 
condition of the projector.
•  Periodically clean the ventilative hole by 
vacuuming it off with a vacuum cleaner.
•  The ventilative holes should be cleaned 
every 100 hours of use. Clean the 
ventilative holes more often when the 
projector is used in a dirty or smoky 
location.
Cleaning the 
Ventilative Holes
1Turn off the power and 
disconnect the power cord.
Press  on the...

56
Appendix
About the Lamp
The projector lamp has a life of 2000 hours. Maintain proper ventilation to keep the lamp operating 
throughout its lifetime. Do not subject the projector to unnecessary vibration to ensure that the 
lamp does not break.
„It is recommended that the lamp (sold separately) be replaced after approximately 2,000 cumulative hours 
of use or when you notice a significant deterioration in the picture and color quality. The number of hours 
the lamp has been used can be checked with...

Appendix
57
Removing and Installing the Lamp Unit
Follow these instructions to replace the lamp.
•  Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or 
the inside of the projector.
•  To avoid injuring yourself and damage to the lamp, be sure to carefully follow the steps below.
•  Do not loosen other screws except for the lamp unit cover and lamp unit. 
(Only the silver screws are loosened).
1. If the projector is running, press  on the projector or...

58
Appendix
4. Remove the lamp unit.
•  Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction 
of the arrow.
   
5. Insert the new lamp unit.
•  Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
•  Attach the lamp unit cover.
•  Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. Then 
tighten the user service screw.
 Info
•  If the lamp unit and lamp cover are...