Studio Experience Projector Premier 30hd User Manual

19
CONNECTIONS AND SETUP
Connecting the Thumbscrew Cables
„Connect the thumbscrew cable making sure that it fits correctly into the 
terminal. Then, firmly secure the connectors by tightening the screws on 
both sides of the plug.
„ Do not remove the ferrite core attached to the HD 15-pin VGA cable.
“Plug and Play” Function
„This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC 
compatible computer will communicate their setting requirements, allowing for quick and...

20
CONNECTIONS AND SETUP
Using the Adjustment Feet
The height of the projector can be adjusted 
using the adjustment feet when the surface 
the projector is placed on is uneven or when 
the screen is slanted. 
The projection of the image can be made 
higher by adjusting the projector when it is in a 
location lower than the screen.
1Press the foot releases and lift 
the projector to the desired 
angle.
2Remove your hands from the foot 
releases. Once the adjustment 
feet have locked in position, 
place...

21
CONNECTIONS AND SETUP
Adjusting the Lens
Using the Lens Shift
The image is focused and adjusted to the 
desired size using the focus ring or zoom ring 
on the projector.
1Zoom is adjusted by rotating the 
zoom ring.
2Focus is adjusted by moving the 
focus ring.
The height and width of the projected image 
can be adjusted to be within the shift range of 
the lens by rotating the lens shift dial at the top 
of the projector.
 Note
•  Do not forcibly turn the lens shift dial beyond 
the range of the...

22
CONNECTIONS AND SETUP
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Standard Setup (Front Projection)
„Place the projector at the required distance from the screen 
according to the desired picture size. (See page 23)
An Example of Standard Setup
 Note
•  The projector lens should be centered in the middle of the screen. If the horizontal line passing through 
the lens center is not perpendicular to the screen, the...

23
CONNECTIONS AND SETUP
Screen Size and Projection Distance　
When using a wide 
screen (16:9)
In case of displaying the 
16:9 picture on the whole 
area of the 16:9 screen.
When using a normal 
screen (4:3)
In case of setting the 
16:9 picture to the full 
horizontal width of the 4:3 
screen.
z x
y
The formula for screen size and projection distance
Screen Size (16:9) Projection DistanceDistance from Lens center to 
the lower edge of the image 
Diagonal Wide Hight Max Min upper lower
300” 261” 147”...

24
CONNECTIONS AND SETUP
Projection from behind the screen
Projecting a Reversed/Inverted Image
„Place a translucent screen between the projector and the 
audience.
„Reverse the image by setting “Rear” for “PRJ Mode” in the 
“Options” menu.
Projection using a mirror
„Place a mirror (normal flat type) in front of the lens.
„Reverse the image by setting “Rear” for “PRJ Mode” in the 
“Options” menu, when the mirror is placed on the side 
where the audience is.
Ceiling-mount setup
„It is recommended that you...

25
Basic Operation
Basic Operation 

26
Basic Operation
Image Projection
Basic Procedure
Connect the required external equipment to 
the projector before operating the following 
procedures.
 Info
•  The language preset at the factory is 
English. If you want to change the on-
screen display to another language, reset 
the language according to the procedure 
on 
page 28.
1Plug the power cord into the wall 
outlet.
•  The power indicator illuminates blue, 
and the projector enters standby 
mode.
2Press  on the remote control 
or  on the...

27
Basic Operation
3Press   on the projector to 
select the INPUT mode.
 Note
•  When a signal is not received, 
“Searching” will be displayed.
 Note
•  If you select “Auto” as the input 
source, then the correct input source 
is selected automatically.
4Press   on the remote control 
or   on the projector, then press 
 Enter to turn off the projector, 
when the confirmation message 
is displayed.
 Note
•  If you accidentally press power   
and do not want to turn off the 
projector, press Exit button or...

28
Basic Operation
Selecting the On-screen 
Display Language
•  The on-screen display language of the 
projector can be set to English, Français, 
Italiano, Deutsch, Español, 中文 , 日本語 , 
한국어.
1Press “MENU”.
•  The menu will be displayed.
2Press  or X  to select 
“Language”.
3Press S or T to select desired 
language, and then press  .
The desired language will be set as the 
on-screen display.
4Press “EXIT”.
Main Menu