Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

ProgrammingC-27
Appendix C - Networking Systems
Station User Impacts
Digital Station Displays
Node to Node
When dialing from one Node to another Node, the display of the dialing station reflects the
station dialed (e.g., 3400). The display then updates with either the name or the number of
the dialed station.
When receiving a call from another Node, it resembles a station call.
Node to Node - DND or Forwarding In Use
When calling from one Node to another, it is possible to encounter a station that is in...

C-28Quick Start Procedure
Appendix C - Networking Systems
Conference
When a conference is established between several extensions, either local or remote, the
display will show the following message:
Quick Start Procedure
Networking uses PRI cards for connecting the systems together; however the telco circuit is a
point-to-point T1,nota PRI. Most telco circuits will reverse the transmit and receive pairs
fromendtoend,soitisimportantthatthisiscorrectedbyswappingtransmitandreceiveat
thehubnetwork PRI(s)....

Quick Start ProcedureC-29
Appendix C - Networking Systems
Example: Hub and 3 Nodes
Hub Programming:
Node 1 Programming:
Node 2 Programming:
Node 3 Programming:
Table No CO Group Ext. Range External BLF
01 00 Ext. range for Hub NA
02 02 Ext. range for Node 1 PRIB slots for Node 2,3
03 03 Ext. range for Node 2 PRIB slots for Node 1,3
04 04 Ext. range for Node 3 PRIB slots for Node 1,2
05-16 00 Entire Ext. range NA
Table No CO Group Ext. Range External BLF
01 00 Ext. range for Node 1 NA
02 02 Ext. range for...

C-30Quick Start Procedure
Appendix C - Networking Systems
Flash 24–Cabinet/Card programming
Partial signaling is allowed on PRIBs (8). Normally a PRIB uses 24 time slots each. You can limit
the number of time slots per card to four (4), or multiples of four (4) up to 20. To use the
feature, program the card ID followed by the number of CO lines to be used in groups of four
(4). A group of four (4) is called a cluster.If a card number is programmed without a cluster
number, all COs on that card are...

Quick Start ProcedureC-31
Appendix C - Networking Systems
LCR Programming
When outbound trunks reside in only one system on the network (i.e., Hub), then LCR must
be activated on all systems to allow dialing out. This is accomplished by routing all outgoing
calls over the network and inserting a 9 in front of the number being dialed to access the
main trunk group of the Hub.
LCR Programming(Hub)
Flash 05
Button 7–Enable
LCR programming(Node)
Flash 05
Button 7–Enable
Flash 75
Button 4–Route List Table...

C-32Quick Start Procedure
Appendix C - Networking Systems
Call Park Programming
Park zones need to be set up for each system in the network so that calls can be parked and
retrieved from any system. The following is an example of how to set this up for a 2-system
network.
Hub
Flash 52–Flexible numbering
Node
Flash 52–Flexible numbering
You need to divide the park zone locations and allow all systems to dial each other’sparkand
retrieve codes. In this example, the 16 park zones were divided in half.You...

D
Voice Over the Internet
Protocol
This chapter contains detailed information about Voice Over the Internet Protocol. 

» » » » » » »  NOTES   » » » » » » » 

Product DescriptionD-3
Appendix D - Voice Over the Internet Protocol
Product Description
TheDiscoveryVoice Over the Internet Protocol (VoIP) printed circuit board (PCB) is for use on
Vodavi key service units (KSUs), that includes the Vodavi telephone systems. It provides an
Ethernet interface to connect the KSU to an Internet Protocol (IP) network. The latest in voice
processing protocols and hardware technologies are used to provide the highest quality
voice over an IP network. In addition to supporting...

D-4Specifications
Appendix D - Voice Over the Internet Protocol
Specifications
TheDiscoveryVoIP card uses Transmission Control Protocol/Internet Protocol (TCP/IP) for
packet delivery over an IP network. Additional standards and protocols are used to provide
DTMF, voice processing, and compression.
TheDiscoveryVoIP card can accommodate up to fourDiscoveryVoIP modules. EachDiscovery
VoIP module provides capability for two ports, resulting in a maximum of eight ports when all
four modules are installed....