Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

IP Telephony Standards and Protocols D-15
Appendix D - Voice Over the Internet Protocol
IP Telephony Standards and Protocols
TheDiscoveryVoIP card uses the H.323 Revision standard for call processing. This is an
updated version of the H.323 standard. It provides a set of standards defining real-time
multimedia communications and conferencing over packet-based networks. These
standards define how components that are built in compliance with H.323 set up calls,
exchange compressed audio and video,...

D-16Vo I P G l o s s a r y
Appendix D - Voice Over the Internet Protocol
VoIP Glossary
This table describes the Internet Telephony terms used in this section:
Term Definition
Asynchronous
TransmissionA method of data transmission which allows characters to be sent at irregular intervals by preceding each
character with a start bit and following it with a stop bit
bps Data bits per second, also known as Baud Rate
DTMF Dual Tone Multi-Frequency
Gateway Bridges H.323 conferences to other network...

E
Customer Database
Programming
This appendix provides information about database programming. Use the detailed
procedures contained in other chapters and appendices for actual programming via
executive display telephone. Use the Customer Database Worksheets in this appendix
to help keep track of the system programming changes made for each individual
system. 

» » » » » » »  NOTES   » » » » » » » 

IntroductionE-3
Appendix E - Customer Database Programming
Introduction
TheXTSsystem is programmed to meet each customer’s individual needs. All programming
is done at any 24-Button Executive Telephone as the programming station or through an
ASCII terminal or PC. The digital display model is required for programming.
When the programming mode is entered, the digital telephone being used no longer
operates as a telephone but as a programming station with all of the buttons redefined. The
keys on the dial...

E-4Introduction
Appendix E - Customer Database Programming
When using a PC to program the system, the following chart presents the data terminal
characters that are equivalent to the key set buttons.
Figure E-1: Data Terminal Program Codes Cross Reference
Some features must have more than one data field programmed for that feature
to work. This information is stated in the instructions.
adm>
REMOTE ADMIN KEY DEFINITION
Keyset   Term   Keyset   Term   Keyset   Term...

IntroductionE-5
Appendix E - Customer Database Programming
Figure E-2: Programming Button Mapping
FLEX 5 FLEX 6 FLEX 7
FLEX 8
FLEX 9FLEX 10FLEX 11
FLEX 12
FLEX 13
FLEX 14FLEX 15FLEX 16
FLEX 17
FLEX 18FLEX 19
FLEX 20
FLEX 21FLEX 22FLEX 23
FLEX 24
TYUI
O
P
AS
DF
GH
J
KL;
Z
XCV
FLEX 1 FLEX 2 FLEX 3
FLEX 4
Q
WER 

E-6 Program Mode Entry (Key Station)
Appendix E - Customer Database Programming
Program Mode Entry (Key Station)
Programming is performed at any 24-button Digital Display Terminal. Programming is always
done at this type of station regardless of the class of service or which station has been
assigned the attendant(s).
To enter the Program Mode:
1. Press the ON/OFF button (optional). LED lights and intercom dial tone sounds.
2. On the dial pad, press [
✳][✳][3][2][2][6] (default password). A confirmation...

Database Programming Worksheets E-7
Appendix E - Customer Database Programming
Database Programming Worksheets
Before attempting programming, it is strongly recommended that customer database
worksheets be prepared (Refer to“Programming Tables”on page E-12). These worksheets
should become part of the permanent record of customer programming. Refer to the
following sections when preparing the worksheets.
Database Upload/Download Routine
The Database Upload/Download Routine (FLASH 86) provides a...

E-8 Database Upload/Download Routine
Appendix E - Customer Database Programming
HYPERTERMINAL -- Uploading a Database File
After opening HyperTerminal, and the New Connection screen displays, complete the
following steps:
1. Type a connection name and select the appropriate icon, then click .
2. When the Phone Number screen displays, change the setting in the Connect Using box
to: Direct to COM1, and then click .
3. Once the COM1 Properties screen displays, change the settings as shown, and then click
.