Sony Vpl Ex130 Projector User Manual

11Location and Function of Controls
Overview
aVentilation holes (exhaust)
bLens
Remove the lens cover before 
projection.
cFront remote control detector
dControl panel
For details, see “Control Panel” on 
page 12.
eZoom ring
Adjusts the picture size.
fFocus ring
Adjusts the picture focus.
gVentilation holes (intake)/Air 
filter cover
hAdjusters (fore pad)
iLamp cover
jAdjuster
kConnector Panel
For details, see “Connector Panel” on 
page 14.
lAC IN socket
Connects the supplied AC power cord.
mIntake vent...

12Location and Function of Controls
a?/1 (On/Standby) key
Turns on the projector when the 
projector is in standby mode. To turn off 
the power, press the ?/1 key twice 
according to the message or hold the ?/1 
key for about one second.
Lights up or flashes under the following 
conditions:
– Lights in red when the AC power cord 
is plugged into a wall outlet. Once the 
projector is in standby mode, you can 
turn it on with the ?/1 key.
– Flashes in red when the temperature 
becomes high inside the...

13Location and Function of Controls
Overview
For details, see page 44.
eMENU key
Displays the on-screen menu. Press 
again to clear the menu.
fPIC MUTING key
Cuts off the picture. Press again to 
restore the picture. 

14Location and Function of Controls
aVIDEO IN connector
S VIDEO (mini DIN 4-pin):
Connects to the S video output of 
video equipment.
VIDEO (phono type):
Connects to the video output of video 
equipment.
AUDIO (stereo minijack):
To listen to sound output from video 
equipment, connect via this jack to the 
audio output of the video equipment.
bINPUT A/B AUDIO connector
Inputs audio signal attached to the image 
from INPUT A or INPUT B.
cINPUT A connector
RGB (HD D-sub 15-pin, female):
Inputs a computer...

15Location and Function of Controls
Overview
The keys that have the same names as those 
on the control panel function identically.
aNETWORK key
This function is not provided in this 
projector.
bINPUT key
cMENU key
dENTER/
v/V/b/B (Arrow) keys
eRESET key
Resets the value of an item to its factory 
preset value or returns the enlarged 
image with D ZOOM key to its original 
size. This key functions when the menu 
or a setting item is displayed on the 
screen.
fAU TO  FOC U S k ey
This function is not...

16Location and Function of Controls
2Install the lithium battery.
3Put the lithium battery holder back 
into the Remote Commander.
Notes on the lithium battery
 A button type lithium battery (CR2025) is 
used in the Remote Commander. Do not 
use batteries other than CR2025.
 Keep the lithium battery out of the reach of 
children.
 Should the battery be swallowed, 
immediately consult a doctor.
Notes on Remote Commander 
operation
 Make sure that nothing obstructs the 
infrared beam between the Remote...

17Installing the Projector / Connecting the Projector
Projecting the Picture
BProjecting the Picture
Installing the 
Projector
This unit can be operated on a floor or 
desktop (floor installation), but also can be 
suspended from a ceiling with a dedicated 
mounting device (ceiling installation).
For details, see “Installation Diagram” on 
page 51.
Connecting the 
Projector
When you connect the projector, 
make sure to:
 Turn off all equipment before making any 
connections.
 Use the proper cables for...

18Connecting the Projector
To connect a computer
1HD D-sub 15-pin cable (supplied)
2Stereo audio connecting cable (not supplied) 
(Use a no-resistance cable.)
 For stereo audio connection, connect the 
stereo audio connecting cable to the INPUT 
A/B AUDIO connector.
 The projector accepts VGA, SVGA, XGA, 
SXGA, SXGA+, WXGA signals. However, 
we recommend that you set the output mode 
of your computer to XGA mode for the 
external monitor.
 If you set your computer, such as a notebook 
computer, to output...

19Projecting
Projecting the Picture
2Video cable (not supplied) or S-Video cable 
(not supplied)
To connect to a video GBR/
Component output connector
1Signal Cable (not supplied)
HD D-sub 15-pin (male) ↔ 3 × phono jack 
2Stereo audio connecting cable (not supplied)
 
(Use a no-resistance cable.)
 For stereo audio connection, connect the 
stereo audio connecting cable to the INPUT 
A/B AUDIO connector.
 Set the aspect ratio using “Aspect” on the 
INPUT SETTING menu according to the 
input signal.
 When...

20Projecting
The ?/1 key lights in red and the 
projector goes into standby mode. 
2Press the ?/1 key.
The ?/1 key lights after flashing in 
green. (The projector cannot be used 
while the ?/1 key is flashing.)
3Turn on the equipment connected to 
the projector.
4Press the INPUT key to select the 
input source.
Each time you press the key, the input 
signal switches as follows:
Smart APA (Auto Pixel Alignment) 
adjusts the picture of the connected 
equipment so that it is projected clearly.
 If “Auto...