Sony Projector Vpl Hw10 User Manual

51 
Using the Menus
Panel AlignmentThis feature allows you to adjust the gaps in the color of 
characters or the picture.
When set to “On”, the “Adjust Color” and the “Pattern Color” can be 
assigned and adjusted.  
Adjust Color: Assigns the desired color to adjust the gaps in color. 
Select “R” (Red) or “B” (Blue) to make adjustments based on “G” 
(Green).
Pattern Color: Select “R/G” (Red and Green) or “R/G/B” (White, 
all colors) when the “Adjust Color” is “R” (Red). Select “B/G” 
(Blue and Green) or...

 52
Information Menu
The Information menu displays the model name, serial number, the horizontal and vertical 
frequencies of the input signal and the cumulated hours of usage of the lamp.
 fH (horizontal frequency) and fV(vertical frequency) may not be displayed depending 
on the input signal used on the projector.
 You cannot change the displays listed above.
Model nameDisplays the model name (VPL-HW10).
Serial No.Displays the serial number.
fH (horizontal frequency)Displays the horizontal frequency of...

53 
Using the Menus
This projector has 38 types of preset data for input signals (the preset memory). When the 
preset signal is input, the projector automatically detects the signal type and recalls the 
data for the signal from the preset memory to adjust it to an optimum picture. The memory 
number and signal type of that signal are displayed in the Information   menu.
You can also adjust the preset data through the Screen   menu.
This projector also contains 20 different user memories beside the...

 54
This section describes about the other functions, how to solve the problems, how to 
replace the lamp and air filter, etc.
About the Control for 
HDMI
What is the Control for HDMI?
Control for HDMI is an HDMI standard 
mutual control function which uses the 
HDMI CEC (Consumer Electronics 
Control) specification. By connecting a 
variety of Control for HDMI compatible 
equipment such as a DVD recorder, an AV 
amplifier, etc., with an HDMI cable, you can 
operate your equipment synchronizing with 
the...

55 
Others
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem 
using the following instructions. If the problem persists, consult with qualified Sony 
personnel.
Power
Picture
Symptom Cause and Remedy
The power is not turned on.cThe power may not turn on if you turn the power off with I/1 
(ON/STANDBY) switch and turn it on again in a short time.
After about 1 minute, turn the power on. 
cClose the lamp cover securely, then tighten the screws...

 56
On-screen display
Remote control
Others
The picture is too dark.cAdjust the “Contrast” or “Brightness” of the Picture   menu 
properly. (1 page 42)
The picture is not clear.cAdjust the focus. (1 page 25)
cCondensation has accumulated on the lens. Leave the projector 
for about 2 hours with the power on.
The picture flickers.cFor pictures from a computer, activate “APA” and adjust the 
current input signal.
cAdjust “Phase” for “Adjust Signal” in the Screen   menu 
properly. (1 page 46)
The color of...

57 
Others
The ON/STANDBY or LAMP/COVER indicator lights up or flashes if there is any 
trouble with your projector.
When a warning indicator other than the above starts flashing, and the symptom persists even after 
carrying out the above methods, consult with qualified Sony personnel. 
Warning Indicators
Symptom Cause and Remedy
LAMP/COVER flashes in 
red. (A repetition rate of 2 
flashes)cClose the lamp cover securely, then tighten the screws securely. 
(1 page 60)
cClose the filter holder securely....

 58
Warning messages
Caution messages
Message Lists
Message Cause and Remedy
High temp.! Lamp off in 1 
min.cTurn off the power.
cCheck to ensure that nothing is blocking the ventilation holes. 
(1 page 13)
Frequency is out of range!cFrequency is out of range. Input a signal that is within the 
acceptable frequency range of the projector. (1 page 66)
Please check Input-A 
Signal Sel.cSet “Input-A Signal Sel.” in the Setup   menu to 
“Computer” when an RGB signal is input from a computer. 
(1 page 48)...

59 
Others
Replacing the Lamp 
and the Air Filter and 
Cleaning the 
Ventilation Holes 
(intake)
Tools you need to get started:
• Projector Lamp LMP-H201 (optional)
Standard Phillips screwdriver
Cloth (for scratch protection)
The lamp used for the light source has a 
certain lifespan. When the lamp dims, the 
color balance of the picture becomes strange, 
or “Please replace the Lamp/Filter.” appears 
on the screen, the lamp may be exhausted. 
Replace the lamp with a new one (not 
supplied) 
without...

 60
3Loosen the screw on the lamp 
cover with a Philips screwdriver, 
and then open the lamp cover.
4Loosen the 3 screws on the 
lamp with the Phillips 
screwdriver. Hold up the handle, 
then pull the lamp straight out.
5Hold the handle of the new lamp 
and push it in securely until it 
reaches the end, and then 
tighten the 3 screws.
Be careful not to touch the optical block 
inside the unit.
6Close the lamp cover, then 
tighten the screws.
Note