Sony F65 Manual

31Basic Settings using the Subdisplay
  Chapter 3   Basic Adjustments and Settings
1Select the color temperature on settings page 1, then 
press the MENU SEL/ENTER dial. 
Settings page 1
2Turn the MENU SEL/ENTER dial to select the color 
temperature, then press the MENU SEL/ENTER dial. 
To set using the VF menu
Set the Color Temperature on the  page in 
the Camera menu  (page 47). 
3-3-7 Setting the SDI OUT2 Output 
Color Space
The color space for the image output from the SDI OUT2 
connector can be...

32Basic Settings using the Subdisplay
  Chapter 3   Basic Adjustments and Settings
2Turn the MENU SEL/ENTER dial to select the look-
up table to apply, then press the MENU SEL/ENTER 
dial. 
To set using the VF menu
Set the LUT on the  page in the VF/SDI 
menu  (page 51) . 
3-3-9 Selecting the Fan Operating 
Mode
You can set the operating mode of the camera’s built-in 
fans. The mode can be set to silence the fan speed noise or 
to provided maximum cooling to suit the shooting 
environment. You can...

33Basic Settings using the Subdisplay
  Chapter 3   Basic Adjustments and Settings
3-3-11 Checking the Remaining 
Media
When the SR-R4 recorder is docked with the camera, an 
estimate of the remaining recording time (recording units: 
minutes) on the memory card can be checked on settings 
page 2 on the subdisplay.
Settings page 2
3-3-12 Checking the File Name
When the SR-R4 recorder is docked with the camera, the 
file name can be checked on Settings page 2 on the 
subdisplay. 
The [NEXT] display shows...

34Basic Settings using the Subdisplay
  Chapter 3   Basic Adjustments and Settings
a) The signal output in the viewfinder is active only when SDI OUT2 is selected as the signal source. 
1Select AS1 to AS4 for the button you wish to assign on 
settings page 3, then press the MENU SEL/ENTER dial. 
Settings page 3
2Turn the MENU SEL/ENTER dial to select the 
function to assign, then press the MENU SEL/ENTER 
dial. 
To set using the VF menu
Set on the  page in the Config menu  (page 
56) . 
3-3-15 Adjusting...

35VF Menu Basic Operation
  Chapter 3   Basic Adjustments and Settings
3-3-16 Checking the Self-Diagnostic 
Results
The results of self-diagnostics can be checked on settings 
page 3. If an internal error occurs, a warning or error 
message is displayed. 
For details about messages, see “Warning/Error 
Messages” (page 66).
3-4 VF Menu Basic 
Operation
Detailed settings that cannot be configured on the 
subdisplay are set in the VF menu displayed in the 
viewfinder or on a monitor. 
The VF MENU button,...

36VF Menu Basic Operation
  Chapter 3   Basic Adjustments and Settings
2Turn the MENU SEL/ENTER dial to select a category, 
then press the MENU SEL/ENTER dial. 
The page select screen appears. Items within the 
selected page and the current values of those items are 
displayed. You can check the items and their values on 
each page by turning the MENU SEL/ENTER dial. 
Pressing the BACK button returns to the top menu 
screen. 
Page select screen
1Category icon
2 Category name
3 Page name
4 Configuration...

37Setting the Shooting Mode
  Chapter 3   Basic Adjustments and Settings
3-5 Setting the Shooting 
Mode
The shooting mode can be set to RAW mode or HD mode. 
You select the mode on the  page of the 
Camera menu (page 47). You can also set the frame rate 
and the encoding on the  page.
 page
RAW/HD
Selects the shooting mode. F65RAW:  Records 16-bit linear RAW data.
HD:  Develops RAW data to HD internally, and records 
HD data. 
F65RAW-HFR:  16-bit linear RAW data recorded at 
120 fps (max.).
Observe the...

38Setting the Output Signal
  Chapter 3   Basic Adjustments and Settings
3-6 Setting the Output 
Signal
3-6-1 Adjusting the Output Signal 
Image
The “look” (tone and color) of the image output on SDI 
OUT1 connector and SDI OUT2 connector can be 
specified. 
This function allows you to adjust the output image on the 
SDI OUT1 connector and SDI OUT2 connector, without 
affecting the main RAW image output. 
Adjusting the SDI OUT1 output signal
You adjust the image on the  page of the VF/
SDI menu. 
 page...

39Viewing and Setting the Viewfinder Display
  Chapter 3   Basic Adjustments and Settings
For details, see “When Color/LUT is selected” 
(page 38) for SDI OUT1.
3-6-2 Selecting the Viewfinder 
Output Signal
This selects the video signals for output on the VF and HD-
Y connectors. 
 page
Select
Selects the image for output. 
The default setting is SDI-OUT2. SDI-OUT1:  Selects the image that is output on the 
SDI OUT1 connector. 
SDI-OUT2:  Selects the image that is output on the 
SDI OUT2 connector. 
3-7...

40Viewing and Setting the Viewfinder Display
  Chapter 3   Basic Adjustments and Settings
eColor temperature
Indicates the state of the color temperature. 
f SDI1 look
Displays the SDI1 look settings for the output image on the 
SDI OUT1 connector. 
g SDI2 look
Displays the SDI2 look settings for the output image on the 
SDI OUT2 connector and in the viewfinder. 
h Highlight clip indicator
Displays the highlight clip indicator status (On/Off). 
Displayed only for the output image on the SDI OUT2...