Sony Dcrtrv890e Manual

							5-48
Address
16
17
63
84
C5
55
75
07
D3
D6
59
01
FF
D0
Data
Address
41
42
Data
26
A1
Address
16
17
86
35
33
AA
90
B6
Data
Address
41
42
Data
69
73
3-5-2. BIST Check
1. Playback System Check
1-1. Preparation for Playback
1) Set the POWER switch to VTR (or PLAYER) position.
2) Connect the adjusting remote commander and set the HOLD
switch to ON (SERVICE) position.
3) Playback the BIST check tape. (XH5-6(NTSC), XH5-6P(PAL))
Note: Perform the following checks in the playback mode.
1-2. IC1814(TRF) BIST(PB) Check
1) Select page: 3, address: 12, set data: 04, and press the PAUSE
button.
2) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
3) Select page: 3, address: 13, set data: 02, and press the PAUSE
button.
4) When the playback system of IC1814(TRF) is normal, the
display data (combination data) of page: 3, address: 16 and 17
agrees with any combination as shown below.
NTSC model
PAL model1-3. IC1601(TFD) BIST(PB) Check
1) Select page: 3, address: 40, set data: 0F, and press the PAUSE
button.
2) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
3) When all playback system of IC1601(TFD) is normal, the
display data (combination data) of page: 3, address: 41 and 42
agrees with any combination as shown below.
NTSC  model PAL model
4) Select page: 3, address: 40, set data: 03, and press the PAUSE
button.
5) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
6) When the video playback system of IC1601(TFD) is normal,
the display data (combination data) of page: 3, address: 41 and
42 agrees with any combination as shown below.
NTSC  model PAL model
7) Select page: 3, address: 40, set data: 05, and press the PAUSE
button.
8) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
9) When the audio playback system of IC1601(TFD) is normal,
the display data (combination data) of page: 3, address: 41 and
42 agrees with any combination as shown below.
NTSC  model PAL model
10) Select page: 3, address: 40, set data: 09, and press the PAUSE
button.
11) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
12) When the subcode playback system of IC1601(TFD) is normal,
the display data (combination data) of page: 3, address: 41 and
42 agrees with any combination as shown below.
NTSC  model PAL model
Address
41
42
Data
7C
01
Address
41
42
Data
A6
E1
Address
41
42
Data
88
A9
Address
41
42
Data
43
C8
Address
41
42
Data
72
CD
Address
41
42
Data
76
A9 
						

							5-49
Address
16
17
Data
9A
13
Address
14
15
Data
12
43
Address
16
17
Data
FB
F4
1-4. IC1600(SFD) BIST(PB) Check
1) Select page: 0, address: 01, and set data: 01.
2) Select page: C, address: AC, set data: 21, and press the PAUSE
button.
3) Select page: C, address: AD, set data: 01, and press the PAUSE
button.
4) Select page: 3, address: 11, set data: 04, and press the PAUSE
button.
5) Select page: 3, address: 12, set data: 08, and press the PAUSE
button.
6) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
7) Select page: 3, address: 13, set data: 03, and press the PAUSE
button.
8) When the playback system from IC1600(SFD) to
IC2002(ADC&DAC) is normal, the display data (combination
data) of page: 3, address: 14 and 15 agrees with any combination
as shown below.
NTSC  model PAL model
9) When the playback system from IC1600(SFD) to IC1602(LIP)
is normal, the display data (combination data) of page: 3,
address: 16 and 17 agrees with any combination as shown
below.
NTSC  model PAL model
10) When the playback system from IC1600(SFD) to IC1601(TDF)
is normal, the display data (combination data) of page: 3,
address: 18 and 19 agrees with any combination as shown
below.
NTSC  model PAL model
11) When the playback system from IC1600(SFD) to IC1501(VFD)
is normal, the display data (combination data) of page: 3,
address: 1A and 1B agrees with any combination as shown
below.
NTSC  model PAL model
12) Select page: C, address: AC, set data: 20, and press the PAUSE
button.
13) Select page: C, address: AD, set data: 00, and press the PAUSE
button.
14) Select page: 0, address: 01, and set data: 00.
Address
14
15
Data
41
81
1E
B4
F0
31
DataAddress
16
17
72
F8
16
5C
DataAddress
18
19
Address
1A
1B
Data
12
43
Address
14
15
Data
2D
7C
Address
16
17
Data
1C
A6
Address
18
19
Data
A7
CC
Address
1A
1B
Data
90
CE
1-5. IC1501(VFD) BIST(PB) Check
1) Select page: 0, address: 01, and set data: 01.
2) Select page: C, address: 60, set data: 06, and press the PAUSE
button.
¥ VBUS/EX BIST(PB) Check
3) Select page: 3, address: 10, set data: 00, and press the PAUSE
button.
4) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
5) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
6) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
7) When the playback system from IC1600(SFD) to IC1501(VFD)
is normal, the display data (combination data) of page: 3,
address: 14 and 15 agrees with any combination as shown
below.
NTSC  model PAL model
8) When the playback system from IC1501(VFD) to
IC756(HONEY) is normal, the display data (combination data)
of page: 3, address: 16 and 17 agrees with any combination as
shown below.
NTSC  model PAL model
¥ UPY Y BIST(PB) Check
9) Select page: 3, address: 10, set data: 88, and press the PAUSE
button.
10) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
11) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
12) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
13) When the playback system from IC1501(VFD) to IC5001,5502
(LCD DRIVER) is normal, the display data (combination data)
of page: 3, address: 16 and 17 agrees with any combination as
shown below.
NTSC  model PAL model
Address
14
15
Data
90
CE
Address
16
17
Data
54
ED
Address
16
17
Data
03
C9 
						

							5-50
¥ UPY Cr BIST(PB) Check
14) Select page: 3, address: 10, set data: 89, and press the PAUSE
button.
15) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
16) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
17) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
18) When the playback system from IC1501(VFD) to IC5001,5502
(LCD DRIVER) is normal, the display data (combination data)
of page: 3, address: 16 and 17 agrees with any combination as
shown below.
NTSC  model PAL model
¥ UPY Cb BIST(PB) Check
19) Select page: 3, address: 10, set data: 8A, and press the PAUSE
button.
20) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
21) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
22) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
23) When the playback system from IC1501(VFD) to IC5001,5502
(LCD DRIVER) is normal, the display data (combination data)
of page: 3, address: 16 and 17 agrees with any combination as
shown below.
NTSC  model PAL model
¥ Preparation of ENC BIST(PB) Check
24) Select page: C, address: 51, set data: 0F, and press the PAUSE
button.
¥ ENC Ya BIST(PB) Check
25) Select page: 3, address: 10, set data: 8B, and press the PAUSE
button.
26) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
27) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
28) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
29) When the playback system from IC1501(VFD) to IC1402 (AOI)
is normal, the display data (combination data) of page: 3,
address: 16 and 17 agrees with any combination as shown
below.
NTSC  model PAL model¥ ENC Yb BIST(PB) Check
30) Select page: 3, address: 10, set data: 8C, and press the PAUSE
button.
31) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
32) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
33) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
34) When the playback system from IC1501(VFD) to IC1402 (AOI)
is normal, the display data (combination data) of page: 3,
address: 16 and 17 agrees with any combination as shown
below.
NTSC  model PAL model
¥ ENC Ca BIST(PB) Check
35) Select page: 3, address: 10, set data: 8D, and press the PAUSE
button.
36) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
37) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
38) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
39) When the playback system from IC1501(VFD) to IC1402 (AOI)
is normal, the display data (combination data) of page: 3,
address: 16 and 17 agrees with any combination as shown
below.
NTSC  model PAL model
¥ ENC Cb BIST(PB) Check
40) Select page: 3, address: 10, set data: 8E, and press the PAUSE
button.
41) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
42) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
43) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
44) When the playback system from IC1501(VFD) to IC1402 (AOI)
is normal, the display data (combination data) of page: 3,
address: 16 and 17 agrees with any combination as shown
below.
NTSC  model PAL model
45) Select page: C, address: 51, set data: 03, and press the PAUSE
button.
46) Select page: C, address: 60, set data: 0E, and press the PAUSE
button.
47) Select page: 0, address: 01, and set data: 00.
Address
16
17
Data
1C
60
Address
16
17
Data
92
5A
Address
16
17
Data
3C
D2
Address
16
17
Data
14
A7
Address
16
17
Data
B8
67
Address
16
17
Data
69
21
B2
E7
DE
EE
DataAddress
16
17
Address
16
17
Data
83
9E
FE
68
22
CA
DataAddress
16
17
70
D5
43
E4
DataAddress
16
17
ED
CB
9A
1E
DataAddress
16
17
Address
16
17
Data
CC
ED 
						

							5-51
Address
1A
1B
Data
D5
0B
C2
42
A7
DD
DataAddress
41
42
Address
1A
1B
Data
34
8A
55
B5
1A
04
DataAddress
41
42
2D
F5
A2
7B
DataAddress
16
17
6C
C7
23
76
DataAddress
18
19 2. Recording System Check
2-1. Preparations for recording
1) Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL))
2) Select page: 3, address: 10, set data: C0, and press the PAUSE
button.
3) Select page: 3, address: 11, set data: 07, and press the PAUSE
button.
4) Enter the stop mode.
5) While keep the HOLD switch of the adjusting remote
commander at ON(SERVICE) position, eject the BIST check
tape and insert a tape for recording in place of the tape.
6) Enter the camera recording mode.
Note:Perform the following checks in the camera recording
mode.
2-2. IC1501(VFD) BIST(REC) Check
1) Select page: 3, address: 12, set data: 10, and press the PAUSE
button.
2) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
3) Select page: 3, address: 13, set data: 04, and press the PAUSE
button.
4) When the recording system from IC1501(VFD) to
IC1600(SFD) is normal, the display data (combination data)
of page: 3, address: 14 and 15 agrees with any combination as
shown below.
NTSC  model PAL model
2-3. IC1600(SFD) BIST(REC) Check
1) Select page: 0, address: 01, and set data: 01.
2) Select page: C, address: AC, set data: 21, and press the PAUSE
button.
3) Select page: C, address: AD, set data: 01, and press the PAUSE
button.
4) Select page: 3, address: 11, set data: 04, and press the PAUSE
button.
5) Select page: 3, address: 12, set data: 08, and press the PAUSE
button.
6) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
7) Select page: 3, address: 13, set data: 03, and press the PAUSE
button.
8) When the recording system from IC1600(SFD) to IC1602(LIP)
is normal, the display data (combination data) of page: 3,
address: 16 and 17 agrees with any combination as shown
below.
NTSC  model PAL model
9) When the recording system from IC1600(SFD) to
IC1601(TFD) is normal, the display data (combination data)
of page: 3, address: 18 and 19 agrees with any combination as
shown below.
NTSC  model PAL model
Address
14
15
Data
D5
0B
00
15
BC
CE
DataAddress
16
17
F7
F6
4F
69
DataAddress
18
19
Address
14
15
Data
34
8A
10) When the recording system from IC1501(VFD) to
IC1600(SFD) is normal, the display data (combination data)
of page: 3, address: 1A and 1B agrees with any combination as
shown below.
NTSC  model PAL model
11) Select page: C, address: AC, set data: 20, and press the PAUSE
button.
12) Select page: C, address: AD, set data: 00, and press the PAUSE
button.
13) Select page: 0, address: 01, and set data: 00.
2-4. IC1601(TFD) BIST(REC) Check
1) Select page: 3, address: 40, set data: 0F, and press the PAUSE
button.
2) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
3) When all recording system of IC1601(TFD) is normal, the
display data (combination data) of page: 3, address: 41 and 42
agrees with any combination as shown below.
NTSC  model PAL model
4) Select page: 3, address: 40, set data: 03, and press the PAUSE
button.
5) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
6) When the video recording system of IC1601(TFD) is normal,
the display data (combination data) of page: 3, address: 41 and
42 agrees with any combination as shown below.
NTSC  model PAL model
7) Select page: 3, address: 40, set data: 05, and press the PAUSE
button.
8) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
9) When the audio recording system of IC1601(TFD) is normal,
the display data (combination data) of page: 3, address: 41 and
42 agrees with any combination as shown below.
NTSC  model PAL model
10) Select page: 3, address: 40, set data: 09, and press the PAUSE
button.
11) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
12) When the subcode recording system of IC1601(TFD) is normal,
the display data (combination data) of page: 3, address: 41 and
42 agrees with any combination as shown below.
NTSC  model PAL model
Address
41
42
Data
BB
4E
Address
41
42
Data
DC
ED
Address
41
42
Data
D7
23
Address
41
42
Data
E4
38
Address
41
42
Data
D9
3C
Address
41
42
Data
47
27 
						

							5-52
13) Select page: 3, address: 40, set data: 01, and press the PAUSE
button.
14) Select page: 3, address: 40, set data: 00, and press the PAUSE
button.
15) When the recording system from IC1601 (TFD) to IC1900
(TRX) is normal, the display data (combination data) of page:
3, address: 43 and 44 agrees with any combination as shown
below.
NTSC  model PAL model
2-5. IC1900(TRX) BIST(REC) Check
1) Select page: 3, address: 12, set data: 04, and press the PAUSE
button.
2) Select page: 3, address: 12, set data: 00, and press the PAUSE
button.
3) Select page: 3, address: 13, set data: 02, and press the PAUSE
button.
4) When all recording system of IC1900 (TRX) is normal, the
display data (combination data) of page: 3, address: 14 and 15
agrees with any combination as shown below.
NTSC  model PAL model
18
F0
C8
FB
DataAddress
43
44
96
D1
BC
0E
DataAddress
14
15
F6
2A
A2
E3
DataAddress
43
44
27
8D
B5
61
DataAddress
14
15 
						

							5-53 3-6. IR TRANSMITTER ADJUSTMENTS
Adjust using a IR receiver jig (J-6082-383-A).
Switch setting:
LASER LINK ................................... ON (Red LED is lit)
1. IR Video Carrier Frequency Adjustment
    (VI-151 board)
Mode VTR stop
Signal Arbitrary
Measurement PointPin 5 of CN003 of IR receiver jig (RF)
(Or Pin !¤ of IC1403)
Measuring Instrument Frequency counter
Adjustment Page C
Adjustment Address 28
Specified Value f = 11.85 ± 0.05 MHz
Connection of Equipment
Connect the measuring device as shown in the following figure,
and adjust.
Fig. 5-3-9.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 0C, set data: 08, and press the PAUSE
button of the adjustment remote commander.
3) Select page: C, address: 28, change the data, and set the video
carrier frequency (f) to the specified value.
4) Press the PAUSE button of the adjustment remote commander.
5) Select page: 3, address: 0C, set data: 00, and press the PAUSE
button of the adjustment remote commander.
6) Select page: 0, address: 01, and set data: 00.
2. IR Video Deviation Adjustment (VI-151 board)
Mode VTR stop
Signal Arbitrary
Measurement PointVIDEO OUT terminal of IR receiver jig
(Terminated at 75 W)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 29
Specified Value A = 1.00 ± 0.05 V
Connection of Equipment:
Connect the measuring device as shown in the following figure,
and adjust.
Fig. 5-3-10.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 0C, set data: 02, and press the PAUSE
button of the adjustment remote commander.
2) Select page: C, address: 29, and change the data, set the video
signal amplitude (A) to the specified value.
4) Press the PAUSE button of the adjustment remote commander.
5) Select page: 3, address: 0C, set data: 00, and press the PAUSE
button of the adjustment remote commander.
6) Select page: 0, address: 01, and set data: 00.
Main unitIR receiver jig
CN003
pin 
5Frequency counter
Main unit IR receiver jig
VIDEO 
OUT75 ½ 
75 
½ (1-247-804-11)Oscilloscope
HA
Fig. 5-3-11 
						

							5-54
3. IR Audio Deviation Adjustment (VI-151 board)
Mode VTR stop
Signal Video : No signal
Audio : Ð400Hz, Ð7.5dBs, Audio left
and right terminal of AUDIO/VIDEO
jack
Measurement Point AUDIO L terminal and AUDIO R
terminal of IR receiver jig
(Terminated at 47kW)
Measuring Instrument Audio level meter
Adjustment Page C
Adjustment Address 2A
Specified Value Signal level: Ð7.5 ± 1.0 dBs
Level difference of L and R: Below
2dB
Connection of Equipment:
Connect the measuring device as shown in the following figure,
and adjust.
Fig. 5-3-12.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Connect the audio level meter to the AUDIO L terminal of the
IR receiver jig.
3) Select page: C, address: 2A, change the data and set the 400Hz
audio signal level to the specified value.
4) Press the PAUSE button of the adjustment remote commander.
5) Connect the audio level meter to the AUDIO R terminal of the
IR receiver jig.
6) Check that the 400Hz audio signal level is within the specified
value. If outside, repeat from step 2).
7) Select page: 0, address: 01, and set data: 00.
Main unit
Audio oscillator
Audio Left
(White) Video
(Yellow)
Audio Right
(Red) AttenuatorAUDIO/
VIDEOIR receiver jig
AUDIO OUT
LR
Audio level meter
47k 
½
600 ½
600 ½: 270 ½ (1-249-410-11) + 330 ½ (1-249-411-11)
47k 
½ (1-249-437-11) 
						

							5-55 3-7. AUDIO SYSTEM ADJUSTMENTS
[Connection of Audio System Measuring Devices]
Connect the audio system measuring devices as shown in Fig. 5-3-13.
Fig. 5-3-13
Recording (Camera mode)
Audio oscillator
Attenuator600 ½Left
RightMain unit
MIC
600 
½: 270 ½ (1-249-410-11) + 330 ½ (1-249-411-11)
Main unit
AUDIO/
VIDEO
OUTLeft (White)
Right 47k 
½
47k ½
Video (Yellow)TV monitor
Audio level meter
or Distortion meter
47k 
½ (1-249-437-11)
Playback
(Red) 
						

							5-56
1. Playback Level Check
Mode VTR playback
Signal Alignment tape:
For audio operation check
(XH5-3 (NTSC))
(XH5-3P (PAL))
Measurement Point Audio left or right terminal of AUDIO
VIDEO jack
Measuring Instrument Audio level meter and frequency
counter
Specified Value 32 kHz mode: 1 kHz, +3.0 ± 2.0dBs
48 kHz mode: 1 kHz, +3.0 ± 2.0dBs
44.1 kHz mode:
The 7.35kHz signal level during EMP
OFF is +2.0 ± 2.0dBs.
The 7.35kHz signal level during EMP
ON is Ð6 ± 2 dB from the signal level
during EMP OFF.
Checking Method:
1) Check that the playback signal level is the specified value.
2. Overall Level Characteristics Check
Mode Camera recording and playback
Signal 400Hz, Ð66 dBs signal: MIC jack left
and right
Measurement Point Audio left or right terminal of AUDIO
VIDEO jack
Measuring Instrument Audio level meter
Specified Value Ð7.5 ± 3.0dBs
Checking Method:
1) Input the 400Hz, Ð66dBs signal in the MIC jack.
2) Record in the camera mode.
3) Playback the recorded section.
4) Check that the 400Hz signal level is the specified value.
3. Overall Distortion Check
Mode Camera recording and playback
Signal 400Hz, Ð66dBs signal: MIC jack left
and right
Measurement Point Audio left or right terminal of AUDIO
VIDEO jack
Measuring Instrument Audio distortion meter
Specified Value Below 0.4%
(200Hz to 6kHz BPF ON)
Checking Method:
1) Input the 400Hz, Ð66dBs signal in the MIC jack.
2) Record in the camera mode.
3) Playback the recorded section.
4) Check that the distortion is the specified value.
4. Overall Noise Level Check
Mode Camera recording and playback
Signal No signal: Insert a shorting plug in the
MIC jack
Measurement Point Audio left or right terminal of AUDIO
VIDEO jack
Measuring Instrument Audio level meter
Specified Value Below Ð45dBs
(IHF-A filter ON, 20kHz LPF ON)
Checking Method:
1) Insert a shorting plug in the MIC jack.
2) Record in the camera mode.
3) Playback the recorded section.
4) Check that the noise level is the specified value.
5. Overall Separation Check
Mode Camera recording and playback
Signal 400Hz, Ð66dBs signal: MIC jack
 [left]
(Connect the MIC jack  [right]
to GND)
Measurement Point Audio  [right] terminal of
AUDIO VIDEO jack
Measuring Instrument Audio level meter
Specified Value Below Ð40dBs (IHF-A filter ON)
< > : Left channel check
[   ] : Right channel check
Checking Method:
1) Input the 400Hz, Ð66dBs signal in the  [left] terminal
of the MIC jack only.
2) Record in the camera mode.
3) Playback the recorded section.
4) Check that the signal level of the audio  [right] terminal
is the specified value. 
						

							5-57
5-4. SERVICE MODE
4-1. ADJUSTMENT REMOTE COMMANDER
The adjustment remote commander is used for changing the
calculation coefficient in signal processing, EVR data, etc. The
adjustment remote commander performs bi-directional
communication with the unit using the remote commander signal
line (LANC). The resultant data of this bi-directional communication
is written in the non-volatile memory.
1. Using the adjustment remote commander
1) Connect the adjustment remote commander to the LANC
terminal.
2) Set the HOLD switch of the adjustment remote commander to
ÒHOLDÓ (SERVICE position). If it has been properly
connected, the LCD on the adjustment remote commander will
display as shown in Fig. 5-4-1.
Fig. 5-4-1
3) Operate the adjustment remote commander as follows.
¥ Changing the page
The page increases when the EDIT SEARCH+ button is
pressed, and decreases when the EDIT SEARCHÐ button is
pressed. There are altogether 16 pages, from 0 to F.
¥ Changing the address
The address increases when the FF ()) button is pressed,
and decreases when the REW (0) button is pressed. There
are altogether 256 addresses, from 00 to FF.
¥ Changing the data (Data setting)
The data increases when the PLAY (() button is pressed,
and decreases when the STOP (p) button is pressed. There
are altogether 256 data, from 00 to FF.
¥ Writing the adjustment data
The PAUSE button must be pressed to write the adjustment
data (B, C, D, F page) in the nonvolatile memory. (The new
adjusting data will not be recorded in the nonvolatile memory
if this step is not performed.)
4) After completing all adjustments, turn off the main power
supply (8.4V) once.
PageDataAddress
Hexadecimal
notation
LCD Display
Decimal notation
conversion value
0123456789ABCDEF
0123456789AbcdEF
0123456789101112131415
2. Precautions upon using
    the adjustment remote commander
Mishandling of the adjustment remote commander may erase the
correct adjustment data at times. To prevent this, it is recommended
that all adjustment data be noted down before beginning adjustments
and new adjustment data after each adjustment.