Sony Dcrtrv890e Manual

							5-8
Address
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
Initial value
NTSC
80
80
D5
EC
20
20
PA L
80
80
D5
EC
20
20
Remark
Fixed data-1
(Initialized data)
PSD sensor gain adj.
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Color reproduction adj. (2)
(ND filter ON)
Fixed data-1
Fixed data-2
Fixed data-1
(Initialized data)
4. E Page tableNote 1:Fixed data-1 : Initialized data. (Refer to Ò1. Initializing the F, E
Page DataÓ.)
Fixed data-2 : Modified data. (Refer to Ò2. Modification of F, E
PAGE DataÓ).
Address
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
Initial value
NTSC
40
40
80
80
80
PA L
40
40
80
80
80
Remark
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
 Pre white balance data input
Fixed data-1
OFFSET adj.
Fixed data-1
(Initialized data) 
						

							5-9
Address
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C to FF
Initial value
NTSCPA LRemark
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
(Initialized data)
Table. 5-1-2 
						

							5-10 1-3. CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the
specified value of ÒComposite Output Y Level AdjustmentÓ and
ÒComposite Output Chroma Level AdjustmentÓ of ÒBase band Block
AdjustmentÓ of ÒVIDEO SYSTEM ADJUSTMENTÓ are satisfied.
1. 27 MHz Origin Oscillation Adjustment (VC-208 board)
Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.
Subject Not required
Measurement Point Pin $¦ of IC204
or Pin @ª of IC207 or Pin &¦ of IC300
Measuring Instrument Frequency counter
Adjustment Page F
Adjustment Address 1C
Specified Value f=13500000 ± 68Hz
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: F, address: 1C, change the data and set the clock
frequency(f) to the specified value.
3) Press the PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
2. IRIS & ND HALL Auto Adjustment
For detecting the position of the lens iris and ND filter, adjust the
hall AMP gain and offset.
Subject Not required
Measurement Point DDS display data of LCD or TV
monitor (Note 5)
Measuring Instrument
Adjustment Page F
Adjustment Address 1E, 1F, 48, 49, 4C, 70
Specified Value IRIS display data :
    
88 to 8A during IRIS OPEN (Note 1)
   14 to 18 during IRIS CLOSE (Note 2)
ND display data :
   14 to 18 during ND filter OFF (Note 3)
   88 to 8A during ND filter ON (Note 4)
Note 1:Select page: 6, address: 01, set data: 01, and press the PAUSE
button of the adjustment remote commander.
Note 2:Select page: 6, address: 01, set data: 03, and press the PAUSE
button of the adjustment remote commander.
Note 3:Select page: 6, address: 1C, and set data: 02.
Note 4:Select page: 6, address: 1C, and set data: 03.
Note 5:DDS display data of LCD or TV monitor.
CA 00 0000
CA 00 
YY XX
           IRIS display data
           ND display data
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 94, and set data: 89.
3) Select page: 6, address: 95, and set data: 16.
4) Select page: 6, address: 01, set data: 6D, and press the PAUSE
button of the adjustment remote commander. (The HALL
adjustment is performed and the adjustment data is stored in
page: F, address: 1E, 1F, 48, 49, 4C and 70.)
5) Select page: 6, address: 02, and check that the data is Ò01Ó.Processing after Completing Adjustments
1) Select page: 6, address: 94, and set data: 00.
2) Select page: 6, address: 95, and set data: 00.
3) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
Checking method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 11, set data: 02, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 6, address: 04, and set data: 03.
4) Select page: 6, address: 01, set data: 01, and press the PAUSE
button.
5) Check the IRIS display data lies within the Ò88Ó to Ò8AÓ range.
6) Select page: 6, address: 01, set data: 03, and press the PAUSE
button.
7) Check the IRIS display data lies within the Ò14Ó to Ò18Ó range.
8) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
9) Select page: 6, address: 1C, and set data: 02.
10) Check the ND display data lies within the Ò14Ó to Ò18Ó range.
11) Select page: 6, address: 1C, and set data: 03.
12) Check the ND display data lies within the Ò88Ó to Ò8AÓ range.
Processing after Completing Check
1) Select page: D, address: 11, and set data: 00, and press the
PAUSE button.
2) Select page: 0, address: 01, and set data: 00.
3) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button.
4) Select page: 6, address: 1C, and set data: 00.
1121324 25 36
37
48
IC
207
26 505175 76 100
1
25
IC300
1121324 25 36
37
48
IC
204
VC-208 board (SIDE A)
VC-208 board (SIDE B) 
						

							5-11
3. Offset Adjustment
Adjust so that the AGC OUT potential lies within the specified value
of the digital clamp.
Subject Not required
Measurement Point DDS display data of LCD or TV
monitor (Note 1)
Measuring Instrument
Adjustment Page E
Adjustment Address 2D, 2E, 2F
Specified Value 50 to B0
Note 1: DDS display data of LCD or TV monitor.
CA 00 0000
CA 00 00
XX
         Object data
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 11, set data: 02, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 6, address: 01, set data: 07 and press the PAUSE
button.
4) Select page: 6, address: 04, and set data: 1F.
5) Check the DDS display data (Rch OPB) satisfies the specified
value. If not perform the Rch offset adjustment.
6) Select page: 6, address: 04, and set data: 20.
7) Check the DDS display data (Gch OPB) satisfies the specified
value. If not perform the Gch offset adjustment.
8) Select page: 6, address: 04, and set data: 21.
9) Check the DDS display data (Bch OPB) satisfies the specified
value. If not perform the Bch offset adjustment.
10) Select page: 6, address: 01, and set data: 05 and press the PAUSE
button.
11) Select page: 6, address: 04, and set data: 1F.
12) Check the DDS display data (Rch OPB) satisfies the specified
value. If not perform the Rch offset adjustment.
13) Select page: 6, address: 04, and set data: 20.
14) Check the DDS display data (Gch OPB) satisfies the specified
value. If not perform the Gch offset adjustment.
15) Select page: 6, address: 04, and set data: 21.
16) Check the DDS display data (Bch OPB) satisfies the specified
value. If not perform the Gch offset adjustment.
¥ Rch offset adjustment
1) Select page: E, address: 0C, set data: 02, and press the PAUSE
button.
2) Select page: E, address: 2D, change the data and adjust the
DDS display data to the specified value.
¥ Gch offset adjustment
1) Select page: E, address: 0C, set data: 02, and press the PAUSE
button.
2) Select page: E, address: 2E, change the data and adjust the
DDS display data to the specified value.
¥ Bch offset adjustment
1) Select page: E, address: 0C, set data: 02, and press the PAUSE
button.
2) Select page: E, address: 2F, change the data and adjust the DDS
display data to the specified value.Processing after Completing Adjustments
1) Select page: D, address: 11, set data: 00, and press the PAUSE
button.
2) Select page: E, address: 0C, set data: 00, and press the PAUSE
button.
3) Select page: 0, address: 01, and set data: 00.
4) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button.
5) Select page: 6, address: 04, and set data: 00. 
						

							5-12
Address
24
25
26
27
28
29
36
PA L
2C
17
78
1D
FB
12
D6
Address
37
38
39
3A
3B
3C
3D
PA L
E6
23
00
19
00
27
A8
4. Flange Back Adjustment
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
4-1. Flange Back Adjustment(1)
Subject Flange back adjustment chart
(2.0 m from the front of the lens)
(Luminance: 230 ± 30 lux)
Measurement Point Check operation on TV monitor
Measuring Instrument
Adjustment Page F
Adjustment Address 24 to 29, 36 to 3D
Adjusting method:
1) Check that at both the zoom lens TELE end and WIDE end,
the center of the chart for the flange back adjustment and center
of the exposure screen coincide.
2) Select page: 0, address: 01, and set data: 01.
3) Check that the data of page: F, address: 24 to 29, 36 to 3D is
the initial value (See table below).
4) Select page: 6, address: 02, and check that the data is Ò00Ó.
5) Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.
6) Select page: 6, address: 01, set data: 15, and press the PAUSE
button of the adjustment remote commander.
( The adjustment data will be automatically input to page: F,
addresses: 24 to 29, 36 to 3D.)
7) Select page: 6, address: 02, and check that the data is Ò01Ó.
Processing after Completing Adjustments
1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
2) Perform ÒFlange Adjustment (2)Ó.
NTSC
8E
1A
80
24
65
11
D6
NTSC
E6
15
45
3F
3F
16
A8
Data Data
4-2. Flange Back Adjustment (2)
Perform this adjustment after performing ÒFlange Back Adjustment
(1)Ó.
Subject Subject more than 500m away
(Subjects with clear contrast such as
buildings, etc.)
Measurement Point Check operation on TV monitor
Measuring Instrument
Adjustment Page F
Adjustment Address 24 to 29, 36 to 3D
Adjusting method:
1) Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500 m away should
not be in the screen.)
2) Select page: 0, address: 01, and set data: 01.
3) Select page: 6, address: 02, and check that the data is Ò00Ó.
4) Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.
5) Place a ND filter on the lens so that the optimum image is
obtain.
6) Select page: 6, address: 01, set data: 29, and press the PAUSE
button of the adjustment remote commander.
(The adjustment data will be automatically input to page: F,
addresses: 24 to 29, 36 to 3D.)
7) Select page: 6, address: 02, and check that the data is Ò01Ó.
Processing after Completing Adjustments
1) Select page: 0, address: 01, and set data: 00.
2) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Perform ÒFlange Back CheckÓ. 
						

							5-13
A=B
C=D
ABC
D
t=0 ± 0.1msec
V
Color bar chart picture frame
TV monitor picture frame
5. Flange Back Check
Subject Siemens star
(2.0 m from the front of the lens)
(Luminance: 300 ± 50 lux)
Measurement Point Check operation on TV monitor
Measuring Instrument
Specified Value Focused at the TELE end and WIDE
end.
Switch setting:
1) DIGITAL ZOOM (Menu display) ................................... OFF
Checking method:
1) Place the Siemens star 2.0m from the front of the lens.
3) Shoot the Siemens star with the zoom TELE end.
4) Turn on the auto focus.
5) Check that the lens is focused (Note).
6) Turn off the auto focus.
7) While observe the TV monitor, change the zoom to the WIDE
end and check that the lens is focused.
Note :When the auto focus is ON, the lens can be checked if it is focused
or not by observing the data on the page 1 of the adjustment remote
commander.
1) Select page: 6, address: 04, and set data: 0F.
2) Page 1 shows the state of the focus.
1 : 00 : 
XX
          Odd: Focused
          Even: Unfocused
Processing after Completing Adjustments
1) Select page: 6, address: 04, and set data: 00.6. Picture Frame Setting
Subject Color bar chart standard picture frame
(95cm from the front of the lens)
Measurement Point Video output terminal
Measuring Instrument Oscilloscope and TV monitor
Specified Value A=B, C=D, t=0 ± 0.1msec
Setting method:
1) Adjust the zoom and the camera direction, and set to the
specified position.
2) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following
adjustments using ÒColor bar chart standard picture frameÓ.
Check on the oscilloscope
1. Horizontal period
Fig. 5-1-6
2. Vertical period
Fig. 5-1-7
Color on the TV monitor
Fig. 5-1-8 
						

							5-14
7. Pre White Balance Data Input
At 3200k, input the pre white balance standard data.
Subject Clear chart
(Color bar standard picture frame)
Adjustment Page E
Adjustment Address 2A, 2B
Switch setting:
1) ND filter ........................................................................... OFF
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 1C, and set data: 02.
3) Select page: F, address: 20, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: F, address: 21, set data: 28, and press the PAUSE
button.
5) Select page: F, address: 22, set data: 00, and press the PAUSE
button.
6) Select page: F, address: 23, set data: 50, and press the PAUSE
button.
7) Select page: 6, address: 01, set data: 7F, and press the PAUSE
button.
8) Select page: 6, address: 01, and set data: 7D, press the PAUSE
button.
(When the standard data is take in, the data will be automatically
input to page: E, address: 2A and 2B.)
9) Select page: 6, address: 02, and check that the data is Ò01Ó.
Processing after Completing Adjustments
1) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 6, address: 1C, and set data: 00.
3) Select page: 0, address: 01, and set data: 00.
4) Perform ÒAuto White Balance Standard Data InputÓ.8. Auto White Balance Standard Data Input
At 3200K, input the white balance standard data.
Subject Clear chart
(Color bar standard picture frame)
Adjustment Page F
Adjustment Address 20 to 23
Note 1: Perform ÒPre White Balance Data InputÓ before this adjustment.
Note 2:Check that the data of page: 6, address: 02 is 00. If not, turn the
power of the unit OFF/ON.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 01, and set data: 11, and press the
PAUSE button of the adjustment remote commander.
3) Select page: 6, address: 01, and set data: 0B, and press the
PAUSE button.
(When the standard data is take in, the data will be automatically
input to page: F, address: 20 to 23.)
4) Select page: 6, address: 02, and check that the data is Ò01Ó.
Processing after Completing Adjustments
1) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 01, and set data: 00. 
						

							5-15
9. MAX GAIN Adjustment
Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects in
low illuminance will not be produced (dark).
Subject Clear chart
(Color bar standard picture frame)
(95cm from the front of the lens)
Adjustment Page F
Adjustment Address 2C
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 96, and set data: 00.
3) Select page: 6, address: 97, and set data: 2C.
4) Select page: 6, address: 01, set data: 6F and press the PAUSE
button of the adjustment remote commander.
(When the adjustment data is take in, the data will be
automatically input to page: F, address: 2C.)
5) Select page: 6, address: 02, and check that the data is changed
to Ò01Ó.
Processing after Completing Adjustments
1) Select page: 6, address: 96, and set data: 00.
2) Select page: 6, address: 97, and set data: 00.
3) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.10. LV Standard Data Input
Adjust the normal coefficient of the light value.
Subject Clear chart
(Color bar standard picture frame)
Adjustment Page F
Adjustment Address 3E,  3F
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 01, and set data: 0D, and press the
PAUSE button of the adjustment remote commander.
(When the adjustment data is take in, the data will be
automatically input to page: F, address: 3E and 3F.)
Processing after Completing Adjustments
1) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 01, and set data: 00. 
						

							5-16
11. White Balance ND Filter Compensation Adjustment
Compensate the white balance deviation when ND filter is ON.
Subject Clear chart
(Color bar standard picture frame)
Adjustment Page F
Adjustment Address 4A, 4B
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 1C, and set data: 03.
3) Wait for 2 seconds.
4) Select page: 6, address: 01, and set data: 11, and press the
PAUSE button of the adjustment remote commander.
5) Select page: 6, address: 01, and set data: 09, and press the
PAUSE button.
(When the adjustment data is take in, the data will be
automatically input to page: F, address: 4A and 4B.)
6) Select page: 6, address: 02, and check that the data is changed
to Ò01Ó.
Processing after Completing Adjustments
1) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 6, address: 1C, and set data: 00.
3) Select page: 0, address: 01, and set data: 00.12. Auto White Balance Adjustment
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility will
be poor.
Subject Clear chart
(Color bar standard picture frame)
Filter Filter C14 for color temperature
correction
Adjustment Page F
Adjustment Address 34, 35
Adjusting method:
1) Place the C14 filter for color temperature correction on the
lens.
2) Select page: 0, address: 01, and set data: 01.
3) Select page: 6, address: 01, set data: 83, and press the PAUSE
button of the adjustment remote commander.
4) Select page: 6, address: 01, set data: 81, and press the PAUSE
button.
(When the adjustment data is take in, the data will be
automatically input to page: F, address: 34 and 35.)
5) Select page: 6, address: 02, and check that the data is changed
to Ò01Ó.
Processing after Completing Adjustments
1) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 01, and set data: 00. 
						

							5-17
13. Color Reproduction Adjustment (ND Filter OFF)
When the ND filter is off, adjust the color difference matrix
coefficient so that proper color reproduction is produced.
Subject Color bar chart standard picture frame
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Adjustment Page F
Adjustment Address 44, 45, 46, 47
Specified Value All color luminance points should
settle within each color reproduction
frame.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: F, address: 5E, set data: 1C, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 6, address: 01, set data: 61, and press the PAUSE
button of the adjustment remote commander.
4) Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
5) Change the data of page: F, address: 44, 45, 46 and 47, and
settle each color luminance point in each color reproduction
frame.
Note :Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data will
not be written to the memory.
Processing after Completing Adjustments
1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
2) Select page: F, address: 5E, set data: 25, and press the PAUSE
button.
3) Select page: 0, address: 01, and set data: 00.14. Color Reproduction Adjustment (ND Filter ON)
When the ND filter is on, adjust the color difference matrix
coefficient so that proper color reproduction is produced.
Subject Color bar chart standard picture frame
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Adjustment Page E
Adjustment Address 62, 63, 64, 65
Specified Value All color luminance points should
settle within each color reproduction
frame.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: F, address: 5E, set data: 1C, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 6, address: 1C, set data: 03.
4) Wait for 2 seconds.
5) Select page: 6, address: 01, set data: 85, and press the PAUSE
button of the adjustment remote commander.
6) Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
7) Change the data of page: E, address: 62, 63, 64 and 65, and
settle each color luminance point in each color reproduction
frame.
Note :Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data will
not be written to the memory.
Processing after Completing Adjustments
1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
2) Select page: 6, address: 1C, set data: 00.
3) Select page: F, address: 5E, set data: 25, and press the PAUSE
button.
4) Select page: 0, address: 01, and set data: 00.
NTSC burst position
PAL burst position
NTSC burst position
PAL burst position
Fig. 5-1-9 Fig. 5-1-10