Smeg St338l Instruction Manual

 
 
User instructions   
 
 39 
  
  
 
BEFORE  STARTING  THE  DISHWASHER  AFTER  PROLONGED 
DISUSE: 
 
·  Check  that  there  are  no  deposits  of  sludge  or  rust  inside  the  water 
pipe: if there are, allow the water to run from the water supply tap for 
a few minutes. 
·  Plug the power cord  back into the socket. 
·  Reconnect the water intake hose and open the tap ag ain. 
 
 
 
TROUBLESHOOTING MINOR PROBLEMS 
 
In some cases it is possible to remedy minor problems by referring to the...

 
 
User instructions   
  
40  
  
 
If the dishes fail to dry or remain dull, check tha t: 
 
·  there is rinse aid inside the special container; 
·  the rinse aid dispenser setting is correct; 
·  the  detergent  used  is  of  good  quality  and  has  not  l ost  its 
effectiveness  (for  example,  through  incorrect  storage,  with  the  box 
left open). 
 
If the dishes show signs of streaking, staining, et c., check that: 
 
·  the rinse aid dispenser setting is not too high. 
 
If there are...

 
 
User instructions   
 
 41 
6.  Troubleshooting 
 
  The  dishwasher  is  able  to  indicate  a  series  of 
malfunctions  by 
illuminating  a  number  of  lights  simultaneously  (see   key  below); “E”  or 
“Err”  (depending on the model) also appears on the displa y in the event 
of a malfunction.
 
 
FAULT DESCRIPTION 
E1  
Acquastop failure 
The  anti-flooding  system  has  been  activated  (for  th e 
relevant  models  only).  The  system  is  tripped  in  case 
of water leaks. Contact the...

 
 
User instructions   
  
42 
 
FAULT DESCRIPTION 
E7  
Turbine flow-regulator malfunction  
(for the relevant models only)  
The appliance is not able to measure the amount 
of  water  loaded  accurately.  Interrupt  the  program 
and  switch  off  the  dishwasher.  Switch  the 
dishwasher  back  on,  program  it  again  and  start 
the  washing cycle.  If  the  problem  persists, contact  
the after-sales service. 
E8  
Alternate washing system malfunction 
Interrupt  the  program  and  switch  off...

 
 
User instructions   
 
 43 
  
TECHNICAL DATA 
Width 597 ¸ 599 mm 
Depth measured flush with the  outer edge of the control panel 550 mm 
Height (depending on models) from 820 mm to 890 mm from 860 mm to 930 mm 
Capacity 14 Standard place settings 
Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) 
Electrical characteristics See rating plate 
    
   

c:QUOTE CRITICHE DI CONTROLLO :QUOTE CRITICHE DI CONTROLLO
LE AREE O QUOTE MODIFICATE SONO EVIDENZIATE
LE AREE O QUOTE MODIFICATE SONO EVIDENZIATE
DA SPLINE TRATTEGGIATE DA SPLINE TRATTEGGIATE
LE QUOTE O TOLL.MODIF.PER AGGIOR.DEL DIS.AL LE QUOTE O TOLL.MODIF.PER AGGIOR.DEL DIS.AL
PEZZO, SONO PRECEDUTE DA # PEZZO, SONO PRECEDUTE DA #
B A
A:TERMOPLAST./ACCIAIO/ALLUM. A:TERMOPLAST./ACCIAIO/ALLUM.B:GOMMA E ALTRI MATERIALI
B:GOMMA E ALTRI MATERIALI
Approvato:
Approvato:Verifica:
Verifica:
±1,80 ±1,60
±1,60...