Siemens SD-192/SD-192MX AND SD-232 Programming Manual

							SET - 30
INSTALLATION MANUAL
TA-S30-1
Nov. 1, 1984 
						

							.
.
SET-30 INSTAUAZION AND PROGRAMMING
The following informgtion is a SylnOpSiS df the installation and
programming proceduresoutlined in the SET-30 Documentation
Package.
It is intended to provide the craftsperson with a quick over-
view of the steps- which have to be taken to install and 
program
a SET-30.
For more detailed information,referto the Documentation
Package.
i.-.,”
-2- 
						

							SET-30
SPECIFICATIONS
AUTOCOM
Number of Loops
PBX Loop Resistance
Loop TypePower Loop Resistance
Power Loop Distance
Voltage
Hold
Frequence Response
Tones
Keys
Display
Speakerphones
Handset
Data Retention
FCC Specification2 + Intercom
1200 Ohm maximum
Loop Start
120 Ohm maximum
2200 FT @ 24 GA
24 to 56 VDC
Non-polarity Sensitive
Hard hold on all lines
300 
-.3,400 Hz
;kandard 12 DTMF
32 5x7 matrix,alphanumeric character,
LCD technology
Integral
- Half Duplex
Standard K-type with modular connection
6 Years without power
Meets or exceed parts:
15 subpart J- Class A (EMI)
68 (network connection)
MULTIPLEXER
PBX Loop Type
PBX Lines
Secretary Stations
Power ConnectionLoop Start
8 (32 with 4 multiplexers)
1 (2 on Multiplex II version)
42-56 VDC, 200 MA plus 200 MA per
phone maximum
Polarity sensitive
All specifications and prices are subject to change without notice.
-3- 
						

							FORM
Note:These items are supplied by Siemens-.a.?y----_-c------------------------_ ___-----------------________________o___--------------------------_____-------------------------------------
t ITEMNOMENCLATUREDESCRIPTION
QUANTITY I
I-----------------------------
-------------------------__--------------------------------------------------------------------------------__
I Programmable SET-30 Telephone 1
PN-X5051-Al001 (Exec. See lr 2# orPrivate) I
I-I
121Multiplexer 1
PN-X5051-Al.02
13iMultiplexer PN-X5051-A103 2I-I
I 4 I Power buffer Card
PN-X5051-Al.04
i 5 i Local Power Adapter
II 24 vdc 0:25A PN-X5051-Al01
I
I
I Single Secretary Multiplexer I
iw/8 power corm.I
I Dual Secretary Multiplexer .w/8/
Ipower corm.I 
-i
I For up to 25 SET-30EsI
1Provides fused power corm.I-I
I
f Power supply for one SET-30
/
I
II
i-iii
I 6 I Card Cage AssemblyI Holds up to 13 multiplexer
I IPN-X5051-Al05I assemblies.Requires power III I
I-I
1 supply.I
II
(.
,’
.’ ,
‘\,.::.,I ,
-4- 
						

							/---.
SET-30 can be programmed to operatein any ofthe .configurations
shown below:
1.2 dedicated line buttons stand-alone EXECUTIVE station.
2.2 dedicated line buttons plus intercom
station (with private or group secretary).button
EXECUTIVE
3.2 dedicated line buttons plusintercom button PRIVATE
SECRETARY station, (serving one EXECUTIVE station).
4.4 nondedicated line buttons plus intercom ‘button‘ GROUP
SECRETARY station, serving
UP to 32 EXECUTIVE stations or
nonexecutive stations (2500) phones).
5.5 non-dedicated line buttons(without
intercom)GROUP
SECRETARY station
serving up to 32 EXECUTIVE stations or
nonexecutive stations (2500 phones).
The first or onlysecretary station ofthis type is
programmed as SECRETARY 1.If a second secretary station
is used,it is programmed as SECRETARY 2.
Stand-Alone EXECUTIVE stations are connected to the PBX only.
:One EXECUTIVE, one SECRETARY combinations are connected to the PBX
only with an intercom line between the two stations.
If one SECRETARY station screens callsfor more than one EXECUTIVE _
station a Multiplexer I card is required.
If two SECRETARY stations(both) screencalls for EXECUTIVE
stations,a Multiplexer II card is required.
Each Multiplexer group may use upto four 8-port multiplexer cards
(of the 
same type).
SET-30 is powered locally, using an AC to DC converter,or con-
nected to a multiplexer card,or connected to a power buffer card.
Each power buffercardsupplies power
for 25 instruments,
individually fused at 400 ma @ 48V.
A 16-slot card cageis used to house‘ multiplexer and power buffer
cards.
Multiplexer cards for the same group are placed in adjacent slots.
Each multiplexer group is separated by an empty slot.
If power buffercards are used,
they may be placed in any unoc-
_, cupied slot, including the emptyslot between multiplexer groups.
-5- 
						

							.
Power to the cage for the multiplexerand buffer cards is -48v and
/---..; ~ground from a separate power supply.
Total= 200 ma @ 48V X (number of multiplexer-“\:
cards +number ofmultiplexerand,.
buffer ports used)
Each multiplexer of buffer card is connectedvia a 
2%pair cable to
the MDF (female 
amphenol connector at cag.e end),
‘\
-6- 
						

							SET-30 uses 4-pair wiring (using RI-45 connector)
.CUTIVE St-
.First pair (pin 4&S) T & R for 1st PBX 1~.Connected to PBX station
circuit.
Second pair (pins 3&6) Power (local or from buffer)
Third pair (pins 2&7) Dot used.Fourth pair (pins l&8) T & R for 2nd PRX 11~Connected to PBX station
circuit.Second line Gouldnormally not be used
in this configuration.
.auratlon wle SET-306Stand-alone 
Executive
IPBX
I :
I
-A-:IILine I Line: INTERII1 :2:con :,-’ IISET-30E
EXECUTIVE 
						

							..
DNF: R~~CUTIVE/SX.EWARY COMBIWELQN
..ecutive Statran
First pair (pins 
4&S).T & R for 1st PBX laConnected
toPBXstationcircuitand
crossconnected to first pair -(pins
4&S) of secretary station.
Second pair (pins 
3&6)Power (local or from buffer)
Third pair (pins 
2&7)Uterca- crossconnected tothird
~t;~io~plns2&7) ofsecretary
Fourth pair (pins 
l&8).T & R ior 2nd PRX 1~(optional).
Connected toPBX stationcircuit.
Crossconnected to four‘th pair (pins
l&8) of secretary station,unless
it is a private line.
Note:In the configuration above,
if both PBX station circuits
are crossconnected between the executivestationand
secretary station asshown,the first extension number
will appear on the first button of both instruments, and
the second extension number on the second button of both
instruments.
To have the extension numbers on one of the two instru-
ments reversed, pair 1 at that station is crossconnected
to pair. 4 of the other
station,and pair 4 atthat
/’
‘\
station iscrossconnected topair l- of the other
station.
First pair (pins 4&S)
Second pair (pins 3&6)
Third pair (pins 2~7)
Fourth pair (pins l&8)
T 6 R for
toPBX
vt PBX 1~Connected
stationcircuitand
crossconneeted to first pair (pins
4&5) of executive station.
Power (local or from buffer)
tercogl crossconnectedto third
pair(pins2&7)ofexecutive
station..T C R for 2nd PBX lim(optional).
Connected to PBX station circuit.
Crossconnected to fourth pair (pins
l&8) of executive station,unless
it is a private line.
-8- 
						

							One Private Secretary Serving One Executive with Two Common
Lines and Dedicated IntercomPBX 
-
I
I
I
I
I
III
III II-
II I I
eILine ILine IInterI corn
III
f
lI
ISET-30EI---SET 30-E
III
PRIVATE SECRETARYEXECUTIVE
. .
-9- 
						

							I OR II WIRING
Note:Different multiplexer cards are used for single and dual
secretary applications.-\.i:!/
Each PBX station circuit to appear at aSECRETARY station and
an 
EXECUTIVE station is wired to a line pair on the multiplexer
and the particular line on the 
EXECUTIVEinstrument where it is
to appear (pair 1 or 4 of the 
4-pair modular connector).
Each PBX station circuit to appear at a SECRETARY station and a
conventional telephone (2500 set) is alsowired to a line pair
on the multiplexerand the lineof theinstrument.
(Conven-
tional instruments merely forwardedto a secretary arecon-
nected to the PBX only).
A PBX station circuit appearing ata SECRETARY station only is
wired to a line pair on the multiplexer only.
A PBX stationcircuit appearing atan EXECUTIVE station only
(never to be answered by a secretary) is wired to the par-
ticular line on the EXECUTIVE instrument where it is to appear
(pair 1 or 4 of the cl-pair modular connector).
The INTERCOM pairs of all instruments are wired in parallel and
in addition to pair 11of one of the multiplexer cards in the
multiplexer group.
The T&R pair (pair1 on the 4-pair modular connector) of
SECRETARY % is wired to pair 9of one of the multiplexer cards
in the multiplexer group.
The T&R pair (pair1 on the 4-pair modular connector) of -
SECRETARY II (if used) is wired to pair 10 of one of the multi-
plexer cards in the multiplexer group.
Power for each instrument (pair 2 of the 4-pair modular connec-
tor) may be obtained locally, from the multiplexercard, or a
power buffer card.
-10-