Siemens SD-192/SD-192MX AND SD-232 Programming Manual

This Table Is Used For Programming SPEED DIAL And Access to PBX FEATURES
SUMMARY OF FEATURE SEQUENCE CODES
The following codes as used in feature + ,or speed dial sequences
OH
0-9,*,#
A
B
C
D
EF
GI
GL
GR
Gl or 2
H
J
K0
On hook (OH ti 0H)
DTMF tones
Any tone detect
Busy tone detect
Control tone detect
Dial tone detect
Insert the extension number of the active line
Timed Hookflash/Connect
Get an idle line and connect
Get a line --now active or idle
Get ringing line and connect
Get line 1 or 2
Hang-up
Jam...

LOUDNESS and TONE of RING
Press Volumeor Volumebutton.Instrument will ring.
To increase loudness, press the VOLUMEbutton.
To decrease loudness, press the VOLUMEbutton.
To change the tone, press tone pad buttons 1 through 9 until
desired tone is received.
Press STORE and DISPLAY buttons in sequence
I SELECT MODEI1 AM=l, PM=2, HR=3 1
Enterand STORE
II
/ ENTER HOUR
Enterand STORE
(24-hour time if 3 was chosen in
last step)
1 ENTER MINUTES
I
Enterand STORE
1 ENTER MONTH
I
Enter
(Numeral)and STORE
ii
1 ENTER...

PROGRAMMABLE FFATURR BUTTONS
Fourteen PBX features may be programed to be accessed by a single
button or a combination of two buttons.
Conference Call
. . . . . . . . . . . . . . . .Conference Button
Call Park. . . . . . . . . . . . . . . . . . . . . .Call Park Button.
Pick Up
. . . . . . . . . . . . . . . . . . . . . . . .Pick Up Button
Direct Forward - Activate.,....Direct Forward Button
Direct Forward 
- Deactivate....Direct Forward Button
Any nine
PBX features
FEATURE + button +...

.PROGRAMMABLE FEATURE BUTTONS (cwued)
Copy the command string except for the access code.Use the access
code of the particular PBX with which the SET-30 is to be used.
The existing command string can also be displayed first and then
copied with the new access code.
FEATURE ACCESS SEQUENCE CODES
1 FEATURE OR KEY
1 AND FEATURE
I NAME
llASK 0 SATURN II/SK 1 SD192/19
GLND,KBPH
GLND-KBPHGLND,PH
NOT ASSIGNED
GLND-US
NUF,S
NUFUS
NUFKBS
NUF-KlS
GLND,SGFNUNDRPOH
( OJiQT 0 1
GFNUND,POH
( kB!X 0 1
1 FWN NO...

TROGRAM~ FEATURE BUTTONS (continued)
Enter security key 
= STORE, FEATURE +r 0, STATUS
Note: 
j&z direct forward featureis JuL&W ii&i will ke a@ained mtelv.
Press STORE and FEATURE button.
If the FEATURE+ button was pressed,a feature number is also selected.
If the CONF, PARK, or PICKUP was pressed, skip the next step.
1 SELECT PBXI
1 FEATURE (l-9) I
Enter(Do not press STORE)
Feature number (if used)
1 1 ENTER NUMBER
1
Request a string of commands
(See table on preceding page).
If the string of commands...

~ROGRAMMASLE FEATURE RUTTO~ (continued)
i 1 ENTER (ALPHA)
Press key pad number which corresponds
to the next alpha character desired.
I
(If the next character is a number, press
Ithe SPEED DIAL button first, then enter
the number.
Display above shows the
result of pressing the 1
key in the previous step.
j USE: J-l, K=2, L=3I
Press key pad number which corresponds to
the desired letter shown on left, but do
Inot press STORE button.
Display above shows the
result of pressing the
5 (JKL) key in the...

PROGRAMMABLE FEATURE BUTTONS (continued)/ USE: l=A, 2=B, 3=C
I
I
Display shows the result
of pressing the 2 (ABC)
key in the previous step
Press key pad number which corresponds
to the desired letter shown on left,
but do not pressSTORE button unless
name is finished.
If a number was selected in the previous
step, press key 4.
1 ENTER NAMEIEnter next letter on tone pad
I cI
II
Display shows the result
of pressing the 3 key in
the previous step to
select the third letter
of the three choices.
/ USE: l=Q,...

PROGRA~LE FEATURE RUTTONS (continued1
.Direct Forward Activate
Press STORE, FEATURE 
+,and * buttons in sequence.
I
Using the same procedure described on
* ENTER NUMBER
I/
previous pagesl enter the command string
and press STORE.
/
Using the same procedure described.on
* ENTER NAMEprevious pages,enter the feature name
and press STORE.
To display the feature, press the DISPLAY, FEATURE +, and * buttons in
sequence.
.Direct Forward Deactivate
Press STORE, FEATURE +,anuttons in sequence.
1
t # ENTER NUMBER...

PROGRAMMABLE FEATURE BUTTO% (continued)
Note:When the FEATURE + button is pressed,the first three letters of
the feature name are displayed for features 1 through 6. In order
for the user to recognize the feature, the first three letters
should clearly show the entire feature. When using the feature,
the entire name is displayed.
Examples of Feature names:
FWN -NO ANSWER
FWB - BUSY
Fwc 
-CANCEL
UN1
- ZONE ONE
To display the feature, perform the following procedure:
Press 
DISPLAY and feature button
If...

SET-30 PROGRAMMING
I
./:
This exercise contains four different SET-30 configurations.
Complete the database tables in the back of this booklet for each of
the configurations.
The database tables also contain some wiring information for easy
identification of each station.
After completion of the database tables, program each of the configur-
ations.
RINGING ARRANGEMENT
Selection
1
2
6
7
Description
Duplicate ringing.
Rings both secretarys and executives
phones.
Delayed duplicateringing.Rings at...