Siemens SD-192/SD-192MX AND SD-232 Programming Manual

:
SET - 30
PROGRAMMING MANUAL
SD-192/SD-192MX AND SD-232
‘. ,
.,.“\I _
1,.. ._. .,
-;_ . .
I%-S30-2B
Nov. 1, 1984 

-
SET-38 is programmed from the Key pad in conjunction with the
feature 
,buttons.
General/d-
The STORE button is used at the end of each procedure or during
a procedure to store the programmed information in the instru-
ments memory.
Pressing the SMREbutton in responseto a particular prompt
will leave the programmed informationin tact.
If nothing was
programmed, it will remain blank. It is, therefore, used to
skip prompts,which requireno response duringa change proce-
dure.
4,tx
++The mbuttonis used...

Part of the display will be a number as shownbelow:
= Secretary 1
= Secretary 2PROGRAMMING
Before programming, fill outthe database tables shown on the
next several pages or the tables in the regular SET-30 documen-
tation.
Separate sets of tables are provided for Multiplexer(MUX)
Groups (one or two secretariesand many executives) and Execu-
tive/Private Secretary combinations.
For stand-alone executive phones,use the portion of the Execu-
tive/Private Secretary table which is applicable.
A3- 

,---
El---e-w--~4
---
:-------a-- 44
---
‘\‘;
-4- 

EXECUTIVE (Stand-Alone)
Press STORE, FEATURE +r0, # buttons in sequence.(Disregard
INVALID display between buttons.).
j SELECT MASK (0Enterand STORE
I
ISELECT MODEL
1 SECT=l,EXEC= 2 ;
Enter2-and STORE
II
PressSTORE and COM (3rd ivory button in bottom row) in sequence
I EXTENSION FOR
1 LINE A:
Enterand STORE
iI
(Normally not used) Enter STORE
To display the programmed lines, perform the following procedure:
Press DISPLAY and COM (3rd ivory button in bottom row) in sequence
Enter
and STORE
Not applicable...

MNC ARRANGEMENT AND DIRECT FORWARD DESTINATIONS (STAND-ATlONE EXECDTIV.!j/
Press STORE and DIRECT FORWARD buttons in sequence
Ring arrangement need not be entered.
Press STORE
If no ring arrangement is programmed, it
automatically defaults to arrangement 1.
. .Descr..&ption
7
1,/Duplicate ringing.Rings both secretarys and
executives phones.
Delayed duplicate ringing.Rings of executives
phone.
After two rings, the call also rings at
the secretarys phone.
Executive answers.Rings only at executives
phone....

To display Ring Arrangement and Direct Forward Destination perform the
following procedures:
Press DISPLAY and DIRECT FORWARD buttons in sequence
-Enterand STORE
station to which chosen
line is forwarded
I
V
I AFWD to 1400
1 1 DUPLICATE RING
/A
I
Ring Arrangement used
-7- 

SPEED DIAL
Press STORE and SPEED DIAL buttons in sequence
) y;CH,;OFIONI 
- &-
IEnterbut do not press
ISTORE unless you want to skip
the next step (just change name,
I
not telephone number).
Speed Dial Indexes
1n;fex being programmed
I
t l ENTER NuMBER’I
II
56 digits maximum
(only last 12 will
be displayed in
bottom row as enteredIf the instrument is to merely
outdial digits, enter the tele-
phone number and STORE (preceded
by the PBX trunk group access code
for the trunk group to be used,
unless the...

Press the SPEED DIAL button each time a change from numbers to
alpha characters or vice versa is required.
When the entire string of numbers and alpha characters is
finished, press the STORE button..
------e--e_I__------------------_______
1 1 ENTER NAMEI
II
‘Press tone pad Key which
corresponds to the first
letter or number of name
(Key 1 is used for space).
If no name is desired,
press STORE.
Note:Each numbered Key except 0 and 1 has three letters (0 Key
has two letters and a dash).In order to select...

I
To display SPEED DIAL numbers perform the following procedure:
Press DISPLAY and SPEED DIAL buttons in sequence
Enter indexto be displayed
IndexName
II
VV
.~::;,i
Number dialed(trunk group access code and address)
Note:
The display will show only the last 12 digits. If
more than 12 digits are used, press the 
B&X button
to view the remaining numbers.
To.display the first four letters of the names for the first
six speed call indexes 
(l-61, perform the following procedure:
Press SPEED DIAL button5 6...