Sharp Ux355l Plain Paper Fax Machine Operation Manual

Setting the Date and Time
29
1. InstallationSetting the Date and Time
1Press these keys:
The display will show: Set the date and time by pressing the keys on the operation panel as 
shown below.
ENTRY MODE
The date and time 
appear in the display and 
are printed at the top of 
every page you fax. 
3 key
*
 keyFUNCTION key
STOP keySTART/MEMORY 
key
3
FUNCTION
213
9
456
78
0
Note: The imaging film and printing paper must be loaded before the date 
and time can be set.
Do not set the date and time if you...

Setting the Date and Time
30
7Enter a two-digit number for the hour 
(“01” to “12”) and a two-digit number 
for the minute (“00” to “59”).
Example: 9:25
4Enter a two-digit number for the 
month (“01” for January, “02” for 
February, “12” for December, etc.).
•To correct a mistake, press the 
SPEED DIAL key to move the cursor 
back to the mistake and then enter the 
correct number.
5Enter a two-digit number for the day 
(“01” to “31”).
Example: January
Example: the 5th
6Enter the year (four digits)....

Setting the Date and Time
31
1. Installation
Daylight Saving Time
If desired, you can set the clock to move forward and backward 
automatically at the beginning and end of Daylight Saving Time. To 
turn on this function, press the panel keys as follows:
1Press these keys:
The display will show:
2Press 1 to turn on the Daylight Saving 
Time function, or 2 to turn it off.
or YES NO
3Press the STOP key to return to the 
date and time display.
9Press the START/MEMORY key to 
start the clock.
The display will...

Setting the Reception Mode
32
Setting the Reception Mode
Your fax has three modes for receiving incoming calls and faxes:
TEL mode:
Select this mode when you want to receive both phone calls and faxes 
on the line connected to the fax machine. All calls, including faxes, 
must be answered by picking up the fax machines handset or an 
extension phone connected to the same line.
FA X mode:
Select this mode when you only want to receive faxes on your line. 
The fax machine will automatically answer all...

Volume Adjustment
33
1. Installation
Volume Adjustment
You can adjust the volume of the speaker and ringer using the UP and 
DOWN keys.
2Press the UP or DOWN key.
3When the display shows the desired 
volume level, press the SPEAKER 
key to turn off the speaker.
SPEAKER: HIGH
Display:
SPEAKER: MIDDLE
SPEAKER: LOW
or
Handset
1Lift the handset. Speaker
1Press the SPEAKER key.
DOWN key
UP key
SPEAKER
SPEAKER
 DOWN   UP  
213
9456780
all.book  Page 33  Wednesday, April 26, 2000  7:08 PM 

Volume Adjustment
34
Ringer
1Press the UP or DOWN key. (Make 
sure the SPEAKER key has not been 
pressed and the handset is not lifted.)
Display:
RINGER: HIGH
RINGER: MIDDLE
RINGER: LOW
RINGER OFF: OK?
2If you selected RINGER OFF: OK?, 
press the START/MEMORY key.
The ringer will ring once 
at the selected level, then 
the date and time will 
reappear in the display.
2Press the UP or DOWN key.
RECEIVER: HIGH
Display:
RECEIVER: MIDDLE
3When the display shows the desired 
volume level, replace the...

35
2. Setting Up 
OpenLCR
2.  Setting Up and Using OpenLCR
Your fax machine features OpenLCR technology, which helps you 
save money on long distance and international phone calls (both fax 
and voice) by automatically routing each call for the best available 
rate. 
♦OpenLCR service is free of charge. The only cost to you is that of a 
periodic call (usually once every three months) to OpenLCR to 
receive the latest rate data. (Once you have registered with 
OpenLCR, your fax machine automatically makes...

Setting Up and Using OpenLCR
36
Registering by fax
To register by fax, fill in the Fax Transmission Test and OpenLCR 
Line Activation Form, and then fax the form as follows:
 1Place the form with the side you 
wrote on face down, and push it 
gently into the document feeder of the 
fax machine.
The display will show:
READY TO SEND
2Press the OpenLCR key, the 5 key, 
and then the START/MEMORY key.
•Your fax  automatically calls 
OpenLCR and sends the form. After 
the form is sent, your fax will...

Setting Up and Using OpenLCR
37
2. Setting Up 
OpenLCR
Registering by phone
To register by phone, follow these steps:
1Pick up the handset on the fax 
machine. 
1
2Press the OpenLCR key and then the 
1 key.
3If the display shows the alternating 
messages at right, press the number 
keys to enter your fax/phone number, 
including the area code (the number 
must be 10 digits long). When 
finished, press the START/
MEMORY key.
(If the message at right doesn’t 
appear, this step is not necessary.)
SET OWN...

Setting Up and Using OpenLCR
38
4Follow the instructions you hear.
♦Note: If you are on a pulse dial line, press the * key before 
pressing the number keys to respond. 
(This makes your fax temporarily issue tone signals when you press 
the number keys.)
♦When registration is completed, your fax machine will receive the 
rate data from OpenLCR. This will last one or two minutes. When 
downloading is completed, the display will briefly show 
DOWNLOAD OK!! and then revert to the date and time.
♦OpenLCR...