Sharp Ux355l Plain Paper Fax Machine Operation Manual
Here you can view all the pages of manual Sharp Ux355l Plain Paper Fax Machine Operation Manual. The Sharp manuals for Fax Machine are available online for free. You can easily download all the documents as PDF.
Page 11
9 1. Installation 1. Installation Unpacking Checklist If any are missing, contact your dealer or retailer. Before setting up, make sure you have all of the following items. Original document support Handset Handset cord Gears (4) Imaging film (initial starter roll)Paper tray extension Rapid key labels Operation manual Telephone line cord Imaging film cartridge all.book Page 9 Wednesday, April 26, 2000 7:08 PM
Page 12
Connections 10 Connections Points to keep in mind when setting up Do not place the machine in direct sunlight.Do not place the machine near heaters or air conditioners. Keep dust away from the machine.Keep the area around the machine clear. About condensation If the machine is moved from a cold to a warm place, it is possible that condensation may form on the scanning glass, preventing proper scanning of documents for transmission. To remove the condensation, turn on the power and wait...
Page 13
Connections 11 1. InstallationConnecting the Handset Connect the handset as shown and place it on the handset rest. ♦The ends of the handset cord are identical, so they will go into either jack. Use the handset to make ordinary phone calls, or to transmit and receive faxes manually. Make sure the handset cord goes into the jack marked with a handset symbol on the side of the machine! all.book Page 11 Wednesday, April 26, 2000 7:08 PM
Page 14
Connections 12 Connecting the power cord Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet. Caution! Do not plug the power cord into any other kind of outlet. This will damage the machine and is not covered under the warranty. Note: If your area experiences a high incidence of lightning or power surges, we recommend that you install surge protectors for the power and telephone lines. Surge protectors can be purchased at most telephone spe- cialty stores. The machine does not have...
Page 15
Connections 13 1. Installation Connecting the telephone line cord Insert one end of the line cord into the jack on the back of the machine marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line wall telephone jack. Note: The fax machine is set for tone dialing. If you are on a pulse dial line, you must set the fax machine for pulse dialing. Press the keys on the operation panel as follows: 1Press these keys: The display will show: 4 DIAL MODE 2Press 1 to select tone dialing, or 2...
Page 16
Connections 14 Attaching the tray extension and document support Attach the paper tray extension. ♦Pull the paper release plate forward. Insert the paper tray extension horizontally into the notches in the paper tray. Rotate the paper tray extension up until it snaps into place. Attach the original document support. Note: The original document suppor t has a top side and a bottom side. If you cannot insert the tabs on the support into the holes, turn the support over. all.book Page 14...
Page 17
Connections 15 1. Installation Extension phone (optional) If desired, you can connect an extension phone to the TEL. SET jack on the fax. ♦To connect an answering machine to your fax, see Chapter 7, Answering Machine Hookup (page 88). 2Connect the extension phone line to the TEL. SET jack. 1Remove the seal covering the TEL. SET jack. TEL. SETTEL. LINE all.book Page 15 Wednesday, April 26, 2000 7:08 PM
Page 18
Loading the Imaging Film 16 Loading the Imaging Film Your fax uses a roll of imaging film to create printed text and images. The print head in the fax applies heat to the imaging film to transfer ink to the paper. Follow the steps below to load or replace the film.. Note: If there is paper in the paper tray, pull the paper release plate for- ward and remove the paper before loading the imaging film. When replacing the film, use a roll of Sharp UX-3CR imaging film. One roll can print about 100...
Page 19
Loading the Imaging Film 17 1. Installation 4Remove the used film from the cartridge. 5Remove the four green gears from the used film. DO NOT DISCARD THE FOUR GREEN GEARS! 3Remove the imaging film cartridge from the print compartment (grasp the handle at the front of the cartridge) and turn it over. If you are installing the imaging film for the first time, go to Step 6. all.book Page 17 Wednesday, April 26, 2000 7:08 PM
Page 20
Loading the Imaging Film 18 7Insert the large gear into the green end of the empty spool. Make sure the two protrusions on the large gear fit firmly into the slots in the end of the spool. Insert the remaining three gears into the spools, making sure the protrusion on each gear fits firmly into one of the slots in the end of each spool. •If needed, pull the spools apart slightly to allow the gears to fit (the band will stretch). 6Remove the new roll of imaging film from its packaging. •Do not...