Sharp MX M363N User Manual

5-94
SCANNER/INTERNET FAX
Contents
STAMPING SCANNED ORIGINALS (Verif. Stamp)
This function stamps each original that is scanned using the automatic document feeder, allowing you to verify that all 
originals were correctly scanned.
 To use this function, the optional stamp unit must be installed.
 When using USB memory mode, connect the USB memory device to the machine before performing the procedure below.
1
Insert the originals face up in the 
document feeder tray.
2
Specify the destination.
☞
ENTERING...

5-95
SCANNER/INTERNET FAX
Contents
4
Select Verif. Stamp.
(1) Touch the   keys to switch through the 
screens.
(2) Touch the [Verif. Stamp] key so that it is 
highlighted.
(3) Touch the [OK] key.
5
Press the [START] key.
Scanning begins. A beep will sound to indicate that scanning is finished.
To cancel scanning...
Press the [STOP] key ( ) to cancel the operation.
 When two-sided originals are used, the front of each original is stamped twice. (MX-M283N only)
 If an error occurs during scanning, an...

5-96
SCANNER/INTERNET FAX
Contents
SENDING TWO PAGES AS A SINGLE PAGE 
(2in1)
Two original pages can be reduced to half their original size and sent together as a single page.
This function cannot be used in scan mode, USB memory mode, or data entry mode.
1
Place the original.
When placing the originals, orient them as shown below.
2
Specify the destination.
☞
ENTERING DESTINATIONS (page 5-18)
12
12
12
1
2
Portrait-oriented originals
Landscape-oriented originalsTransmission
Transmission
12
12
1
1
1
1...

5-97
SCANNER/INTERNET FAX
Contents
3
Select the special modes.
(1) Touch the [Internet Fax] tab.
(2) Touch the [Special Modes] key.
☞SPECIAL MODES (page 5-71)
4
Select 2in1.
(1) Touch the [2in1] key so that it is 
highlighted.
(2) Touch the [OK] key.
5
Touch the [Original] key.
6
Specify the orientation in which the 
original is placed.
(1) Touch the Image Orientation key with the 
same orientation as the original image.
If this setting is not correct, a suitable image may not be 
transmitted.
(2) Touch...

5-98
SCANNER/INTERNET FAX
Contents
7
Press the [START] key.
Scanning begins.
 If you inserted the original pages in the document feeder tray, all pages are scanned.
A beep will sound to indicate that scanning is finished.
 If you are scanning the original on the document glass, scan each page one page at a time.
When scanning finishes, place the next original and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key.
A beep will sound to indicate that scanning...

5-99
SCANNER/INTERNET FAX
Contents
CHANGING THE PRINT SETTINGS FOR THE 
TRANSACTION REPORT
(Transaction Report)
A transaction report is automatically printed out to alert you when an Internet fax transmission fails or when a broadcast 
transmission is performed. The transaction report contains a description of the transmission (date, start time, name of 
other party, time required, number of pages, result, etc.).
☞INFORMATION APPEARING IN THE RESULT COLUMN (page 5-109)
Transaction reports are printed...

5-100
SCANNER/INTERNET FAX
Contents
5
Press the [START] key.
Scanning begins.
 If you inserted the original pages in the document feeder tray, all pages are scanned.
A beep will sound to indicate that scanning is finished.
 If you are scanning the original on the document glass, scan each page one page at a time.
When scanning finishes, place the next original and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key.
A beep will sound to indicate that...

5-101
SCANNER/INTERNET FAX
Contents
This section explains how to check the status of reserved transmission jobs and received Internet faxes.
JOB STATUS SCREEN
The job status screen is displayed when the [JOB STATUS] key on the operation panel is pressed. The job status 
screen shows the status of jobs by mode. When the [JOB STATUS] key is pressed, the job status screen of the mode 
that was being used before the key was pressed appears.
Reserved transmissions and received Internet faxes are referred to...

5-102
SCANNER/INTERNET FAX
Contents
JOB QUEUE SCREEN AND COMPLETED JOB SCREEN
The job status screen consists of two screens: the job queue screen that shows reserved jobs and the job currently in 
progress, and the completed jobs screen. To switch between the two screens, touch the job status screen selector key 
((2) below).
Job queue screen Complete screen
(1) Mode switch tabs
Use these tabs to change the job status screen mode.
(2) Job status screen selector key
Touch this key to switch between the...

5-103
SCANNER/INTERNET FAX
Contents Job key display
The following information is shown in the job queue keys and completed job keys that appear in the job status screen.
Direct SMTP information is also included in Internet fax transmission/reception information.
(1)Displays the number (position) of the job in the job queue.
When the job currently being transmitted is finished, the 
job moves up one position in the job queue.
This number does not appear in keys in the completed 
jobs screen.
(2) Mode...