Sharp MX M200D User Manual

69
5
ERASING SHADOWS AROUND THE 
EDGES OF A COPY
(Erase copy)
This feature is used to erase shadows that appear around the edges of copies of books and other thick originals. 
(Edge erase)
The feature can also erase the shadow that appears down the centre of books and other originals that open up. 
(Centre erase)
Both the shadow lines around the edges of copies and the shadow at the centre can be erased. (Edge + Centre erase)
 Five selections are available for the erasure width: 0 mm, 5 mm, 10 mm, 15 mm,...

70
CONVENIENT COPY FUNCTIONS
7Select the erasure width with the [ ] 
or [ ] key.
If you select 0 mm (0), the 
printed result is the same as 
when OFF is selected.
8Press the [OK] key.
You will return to the base 
screen.
9Select other copy settings as needed 
and press the [START] key ( ).
To cancel an edge erase 
setting, return to the edge erase 
settings screen and select 
OFF.
OK
MNO
WXYZ
@.-_
AD-END
Downloaded From ManualsPrinter.com Manuals 

71
5
CARD SHOT
When copying a card, this function allows you to print the front and back sides of the card next to each other on a 
single sheet of paper.
This function creates 2 in 1 images of the front and back side of the card and centres them on the paper.
 Paper cannot be fed from the bypass tray.
 The card shot function cannot be used in combination with margin shift, edge erase, dual page copy, 2 in 1 / 4 in 1 
copy, and XY zoom copy.
 When card shot is used, the rotation copy function does not...

72
CONVENIENT COPY FUNCTIONS
8Press the [START] key ( ).
The front side of the card is 
scanned.
9Turn the original over on the 
document glass.
10Press the [START] key ( ).
Copying will start after both 
sides of the original have been 
scanned.
MNO
WXYZ
@.-_
AD-END
Downloaded From ManualsPrinter.com Manuals 

73
6
APPENDIX
SPECIFICATIONS
Name Digital Multifunctional System
MX-M160D MX-M200D
Ty p e D e s k t o p
Photoconductive type OPC drum
Document glass type Fixed
Copy system Laser electrostatic method
Originals Sheets, bound documents, max. original size A3 (11 x 17)
Copy sizes Max. A3 (11 x 17), min. A5 (5-1/2 x 8-1/2)
(A5 (5-1/2 x 8-1/2) can only be fed from tray 1 and the bypass tray)
Image loss: Max. 4 mm (5/32) at top edge and bottom edge, combined maximum of approximately 6 
mm (11/64)
Copying speed...

74
APPENDIX
Output tray specifications
* When the job separator tray kit is installed, 150 sheets in centre tray, 100 sheets in top tray.
The maximum number of pages that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper.
Printer function / scanner function / fax function specifications
See the Operation manual (for printer and scanner) and the Operation manual (for facsimile).
Overall dimensions 590 mm (W) x 574...

75
7
SYSTEM SETTINGS GUIDE
PURPOSE OF THE SYSTEM SETTINGS
The system settings are used by the administrator of the machine to enable or disable functions to suit the needs of your 
workplace.
This manual explains only the system settings that are common to all the functions of the machine, (copy, fax, printer and 
network scanner functions), as well as system settings that are specifically for the copy function. For programs that are 
specifically for the fax function, printer function, or network...

76
PROGRAMMING AN ADMINISTRATOR 
PA S S W O R D
1Press the [SPECIAL FUNCTION] key.
The special function 
screen will appear.
2Select SYSTEM SETTINGS with the 
[ ] or [ ] key.
3Press the [OK] key.
The administrator 
password entry screen 
appears.
4Use the numeric keys to enter the 
five-digit administrator password.
 If this is the first time you are programming the 
administrator password, enter the factory default 
code. (Page 101)
   appears for each digit that you enter.
 The special modes screen...

77
7
SYSTEM SETTINGS LIST
A list of basic programs used for the machine and a list of programs used for the copy function are shown below.
Programs for general use of the 
machine
* OFFSET FUNCTION is not available in some countries 
and regions.
Programs for Copy Mode
Program name Page
ADMINISTRATOR PASSWORD CHANGE
ADMINISTRATOR PASSWORD CHANGE 76
ACCOUNT CONTROL
AUDITING MODE 79
TOTAL/ACCOUNT 79
RESET ACCOUNT 79
ACC. # CONTROL 80
ACCOUNT LIMIT 81
ACC. # SECURITY 81
CANCEL JOBS OF INVALID ACCOUNTS 81...

78
USING THE SYSTEM SETTINGS
1Press the [SPECIAL FUNCTION] key.
The special function 
screen will appear.
2Select SYSTEM SETTINGS with the 
[ ] or [ ] key.
3Press the [OK] key.
The administrator password entry screen appears.
4Enter the administrator password with 
the numeric keys.
   appears for each digit that you enter.
 The mode selection screen appears.
5Select the desired mode with the [ ] 
or [ ] key.
Example: The screen when COPIER is selected.
6Press the [OK] key.
The settings of the 
selected...