Sharp MX M200D User Manual

39
2
ADJUSTING THE DISPLAY CONTRAST
The contrast of the display can be adjusted as explained below.
1Press the [SPECIAL FUNCTION] key.
The special function 
screen will appear.
2Select DISPLAY CONTRAST with 
the [ ] or [ ] key.
3Press the [OK] key.
The display contrast 
adjustment screen will 
appear.
4Adjust the contrast with the [ ] or [ ] 
key.
To reset the contrast to the 
default setting, press the [C] 
key.
5Press the [SPECIAL FUNCTION] key.
You will return to the base 
screen.
EXPOSURECOLOUR...

40
3
PERIPHERAL DEVICES AND 
SUPPLIES
Optional equipment and supplies are explained in this chapter. To purchase optional equipment and supplies, 
contact your authorised service representative.
OPTIONAL EQUIPMENT
Convenient optional equipment can be installed on the machine as needed.
Yes: Can be installed. No: Cannot be installed.
*1 The network expansion kit (MX-NB10) must be installed.
*2 The facsimile expansion kit (MX-FX10) must be installed.
 As a part of our policy of continuous improvement,...

41
PERIPHERAL DEVICES AND SUPPLIES
3
REVERSING SINGLE PASS FEEDER / SINGLE PASS 
FEEDER
For the names of the parts of the RSPF / SPF, see PART NAMES AND FUNCTIONS (page 12).
Specifications
*1 Two-sided scanning is not possible.
*2 During one-sided copying
250-SHEET PAPER FEED UNIT / 2 X 250-SHEET 
PAPER FEED UNIT
 The 250-sheet paper feed unit provides a tray that can hold 250 sheets (80 g/m2 (20 lbs.)) of plain paper.
 The 2 x 250-sheet paper feed unit provides two trays that can each hold 250 sheets...

42
PERIPHERAL DEVICES AND SUPPLIES
STORAGE OF SUPPLIES
Standard supplies for this product that are to be replaced by the user are paper and toner cartridge.
PROPER STORAGE
●Store the supplies in a location that is:
clean and dry, 
at a stable temperature, 
not exposed to direct sunlight.
●Store paper in the wrapper and lying flat.
Paper stored out of the wrapper or in packages 
standing on end may curl or get damp, resulting in 
paper misfeeds.For best copying results, be sure to use only SHARP Genuine...

43
Part 2: Copier Operation
Downloaded From ManualsPrinter.com Manuals 

44
Downloaded From ManualsPrinter.com Manuals 

45
4
COPY FUNCTIONS
This chapter explains the basic procedures for making copies, including selection of the copy ratio and other copy 
settings.
NORMAL COPYING
This section explains how to make a regular copy.
If Auditing mode has been enabled (page 23), enter your 5-digit account number.
Copying from the document glass
1Open the SPF and place the original 
face down on the document glass.
Align the upper left-hand corner 
of the original with the tip of the 
 mark.
The original size is 
automatically...

46
COPY FUNCTIONS
5Press the [START] key ( ) to begin 
copying.
The copy will be delivered to the 
centre tray.
Copying from the SPF
1Open the SPF and make sure that an 
original has not been left on the 
document glass. Gently close the SPF.
2Adjust the original guides to the size 
of the original(s).
3Place the original(s) face up in the 
document feeder tray.
The original size appears in the 
display and the most suitable 
paper size is automatically 
selected.
Insert the stack into the document...

47
COPY FUNCTIONS
4
Auto paper select mode
When auto paper select mode is enabled, AUTO appears in the paper size display. This function automatically 
selects paper that is the same size as the original (A5, B5, B5R, A4, A4R, B4, A3, 5-1/2 x 8-1/2, 8-1/2 x 11, 
8-1/2 x 11R, 8-1/2 x 13, 8-1/2 x 14, 11 x 17 paper).
 If a zoom setting is selected after placing the original, the paper size that is appropriate for the zoom setting will 
be automatically selected.
 Auto paper select mode is cancelled if the...

48
COPY FUNCTIONS
MAKING A COPY DARKER OR LIGHTER
The copy exposure can be adjusted as needed to the original. Three exposure modes are available: AUTO, 
TEXT and PHOTO. When TEXT or PHOTO is selected, the exposure can be manually adjusted to 5 levels.
Auto
This is the default exposure mode. In this mode, the characteristics of an original being copied are read by the 
exposure system and exposure adjustments are made automatically. The exposure level is lowered for coloured 
areas and background...