Sharp Mx-b200 Service Manual

MX-B200  SIMULATION, TROUBLE CODES  10 - 4 8 01 Developing bias[Function]
When [START] key is pressed, the developing bias signal is turned ON for 30sec.
When, however, an actual output value is measured, use simulation 25-01.
After completion of this process, the machine goes into the sub code entry standby mode.
02 Main charger (Grid high)[Function]
When [START] key is pressed, the main charger is outputted for 30sec in the grid voltage HIGH
move.
After completion of this process, the machine goes into...

MX-B200  SIMULATION, TROUBLE CODES  10 - 5 22 06 Developer counter display[Function]
When [START] key is pressed, the developer counter data are acquired and displayed. 
The display method of the value is the same as SIM20-01.
08 SPF counter display (Option)[Function]
The SPF counter is displayed.
[Operation]
The operation is similar to simulation 22-04.
12 Drum counter display[Function]
The drum counter is displayed.
[Operation]
The operation is similar to simulation 22-04.
13 CRUM type...

MX-B200  SIMULATION, TROUBLE CODES  10 - 6 24 07 Drum counter clear[Function]
When [START] key is pressed, the drum counter value is cleared to 0, and 000,000 is dis-
played on the LED/display.
[Operation]
The operation is similar to simulation 22-04.
08 Copy counter clear[Function]
When [START] key is pressed, the copy counter value is cleared to 0, and 000,000 is dis-
played on the LED/display.
[Operation]
The operation is similar to simulation 22-04.
09 Printer counter clear[Function]
When...

MX-B200  SIMULATION, TROUBLE CODES  10 - 7 26 06 Destination setup[Function]
When this simulation is executed, the current set destination is displayed. Enter the code num-
ber corresponding to the desired destination and press [OK]/[START] key to save the setting.
* Code number 2 and 3 cannot be selected.
[Operation]
The operation is similar to simulation 26-02.
07 Machine conditions check[Function]
When this simulation is executed, the current machine setting is displayed.
20 Rear edge void...

MX-B200  SIMULATION, TROUBLE CODES  10 - 8 26 42 Transfer ON timing control 
setup[Function]
Enter the code number with [UP/UP] key and press [START] key, and the entered set value is
saved and the machine enters the sub code input standby state.
Use [Density Select] key to select a mode. The set value of the selected mode is displayed in
the 7seg display. Main 
codeSub 
codeContents Details of function/operation

* The default value, 11, of the transfer ON timing indicates 236msec passed from PS...

MX-B200  SIMULATION, TROUBLE CODES  10 - 9 26 43 Side void setup[Function]
When this simulation is executed, the currently set code of the side void quantity is displayed
(initial display), and the set data are saved. (Setting range: 0 – 10, Default: 4 (= One side
2.0mm)) 
* When the adjustment value is increased by 1, the side void is changed as follows:
Side void adjustment: The side void is increased by 0.5mm. (The side void of Set value x
0.5mm is made.)
[Operation]
The operation is similar to...

MX-B200  SIMULATION, TROUBLE CODES  10 - 10 30 01 Paper sensor status display[Function]
The paper sensor status is displayed on the LED.
∗Since the manual paper feed sensor is a single bypass sensor, its status is not displayed.
41 06 OC cover float detection 
level adjustment (Option)[Function]
When this simulation is executed, the current set value is displayed. When [START] key is
pressed, the mirror base unit moves to the SPF scan position to acquire the OC cover float
detection level.
When the...

MX-B200  SIMULATION, TROUBLE CODES  10 - 11 43 04 Fusing temperature setting 
in multi copy[Function]
For 20th sheet or later in multi copy, the fusing temperature is automatically changed from the
temperature set with simulation 43-01 to the temperature set with this simulation.
When this simulation is executed, the current set code number is displayed. Enter the code
number and press [START] key to change the setting.
[Operation]
The operation is similar to simulation 43-01.
09 Postcard size paper...

MX-B200  SIMULATION, TROUBLE CODES  10 - 12 43 14 Fusing start temperature 
setting[Function]
When this simulation is started, the currently set code number is displayed.
Press [ ] [ ] key to switch the setting, and press [START] key to save it to the EEPROM. 
The machine goes to the sub code entry standby mode.
Switching to each mode is made by [Density Select] key. The set value of the selected mode is 
displayed on the 7seg display.
∗The cassette feed and the manual feed are controlled similarly....

MX-B200  SIMULATION, TROUBLE CODES  10 - 13 46 01 Copy density adjustment 
(300dpi)[Function]
Copy density is set for each mode.
When this simulation is executed, the current set value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased,
the copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker...