Sharp Mx 4100n Owners Manual

38
WHEN INSTALLATION WAS NOT 
SUCCESSFUL
This section provides solutions to possible installation problems. See the following table of contents to locate the 
appropriate page for your question or problem.
4
TROUBLESHOOTING 
 The software cannot be installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38
 The machine is not detected (when connected to a network). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38
 The plug and...

39
WHEN INSTALLATION WAS NOT SUCCESSFUL
The machine is not 
detected (when 
connected to a 
network).Is the machine power on? If the machine is powered off, it will not be detected. 
Switch on the main power switch and the [POWER] key 
( ) in that order. (In Windows, search again after 
powering on the machine.)
Is your computer connected correctly to 
the machine?Make sure that the cable is connected securely to the 
LAN connectors on your computer and the machine.
Check the connections at the hub as...

40
WHEN INSTALLATION WAS NOT SUCCESSFUL
XThe printer driver cannot be installed (Windows 2000/XP/Server 2003)
If the printer driver cannot be installed on Windows 2000/XP/Server 2003, follow the steps below to check your 
computer settings.
1Click the [start] button and then click 
[Control Panel].
In Windows 2000, click the [Start] button, point to 
[Settings], and click [Control Panel].
2Click [Performance and Maintenance] 
and then [System].
In Windows 2000, double-click the [System] icon.
3Click the...

41
REMOVING THE SOFTWARE
To remove the printer driver or software installed using the installer, follow the steps below.
Windows
1Click the [start] button and then click 
[Control Panel].
In Windows 98/Me/NT 4.0/2000, click the [Start] button, 
point to [Settings], and click [Control Panel].
2Click [Uninstall a program].
 In Windows XP/Server 2003, click [Add or Remove 
Programs].
 In Windows 98/Me/NT 4.0/2000, double-click the 
[Add/Remove Programs] icon.
3Select the program or driver that you 
wish to...

MX-4100N/4101N/5000N/5001N Software Setup Guide
PRINTED IN CHINA
2008H KS1
TINSE4228FCZZ
This manual has been printed using a vegetable-based soy oil ink 
to help protect the environment.
!mx4100_us_ins.book  42 ページ  ２００８年７月２９日　火曜日　午後５時１４分 

TO THE ADMINISTRATOR OF THE MACHINE
DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM
Safety GuideSafety GuideSafety Guide
Before installing this product, be sure to read the 
CAUTIONS and INSTALLATION 
REQUIREMENTS sections.
SUPPLIES
SPECIFICATIONS
INSTALLATION REQUIREMENTS CAUTIONS
Keep this manual close at hand for reference 
whenever needed.
MX-4100N
MX-4101N
MX-5001N MODEL:
mx5001_us_saf.fm  -1 ページ  ２００８年９月２４日　水曜日　午前９時４５分 

FAX interface cable and Line cable:
These special accessories must be used with the device.
Notice for Users in U.S.A.
EMC (this machine and peripheral devices)
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio...

1
Contents
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no 
warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not 
responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual. 
©Copyright SHARP Corporation 2008. All rights reserved. Reproduction, adaptation or translation without prior written...

2
CAUTIONS
1. Do not touch the transfer belt. Scratches or smudges on the transfer belt will 
cause dirty prints.
2. The fusing unit is extremely hot.  Exercise care in this area. 
3. Do not look directly at the light source. Doing so may damage your eyes.
4. When the machine is installed, the adjusters (4) must be lowered to the floor 
to secure the machine (prevent it from moving).
Rotate the adjusters in the locking direction until they are in firm contact with 
the floor.
If you find it necessary to...

3
CAUTIONS
Laser information
Wave length 790 nm ±10 nm
Pulse times
(North America and Europe)MX-4100N/4101N:
3.5 µs ±3.5 ns /7 mm Heavy paper 3.2µs ±3.2 ns /7 mm
MX-5001N:
2.8 µs ±2.8 ns /7 mm Heavy paper 3.2µs ±3.2 ns /7 mm
Output power Max 0.6 mW (LD1+ LD2)
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.2-2001)
For North America:...