Sharp Mx 4100n Owners Manual

4
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the 
machine is moved.
1. The machine should be installed near an accessible 
power outlet for easy connection.
2. Be sure to connect the power cord only to a power 
outlet that meets the specified voltage and current 
requirements. Also make certain the outlet is properly 
grounded.
 For the power supply requirements, see the name 
plate in the lower left corner...

5
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for 
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher 
staple cartridge, and transparency film.
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
 clean and dry,
 at a stable temperature,
 not exposed to direct sunlight.
2. Store paper in the wrapper and lying...

6
SPECIFICATIONS
Machine specifications / copier specifications
* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and 
mirror motor at operating speed in each of black and white mode  and color mode, actual time may vary based on environment 
conditions.
NameDigital Full Color Multifunctional System MX-4100N/MX-4101N/MX-5001N
TypeDesktop
Photoconductive typeOPC drum
Printing methodElectrophotographic system (laser)
Developer...

7
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
*1 Output tray (Center tray) cannot  be used when the finisher or saddle stitch finisher is installed.
*2 Type A connectors are located on the fr ont of the machine and on the right side of the machine at the back (total of two 
connectors); however, the connectors  cannot be used simultaneously. Only one of the connectors can be used.
Bypass tray
Paper sizes: 12 x 18, 11 x 17, 8-1/2 x 14, 8- 1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2...

8
SPECIFICATIONS
Continuous copying speeds*
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same 
page (excluding offset output) using plain one-sided paper from a tray other than the bypass tray.
ModelMX-4100N/MX-4101N MX-5001N
Copy ratio100% / Reduced / Enlarged
Copy modeColor  copying Black and white copying Color  copying Black and white copying
11 x 17, A3, 8K19 copies/min. 19 copies/min. 22 copies/min. 22 copies/min.
8-1/2 x 14,...

9
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
Emission concentration 
(measurement according to RAL-UZ122: Edition Jun. 2006)
Automatic document feeder specifications
*1 Scanning in mono 2 mode of one side only is possible in fax and scan send modes. However, when the resolution is 600 x 600 dpi 
in Internet fax mode, the maximum length is 31-31/64 (800 mm). When the resolution is 400 x 400 dpi or 600 x 600 dpi in scan 
mode, a long original cannot be scanned.
*2 Paper...

10
SPECIFICATIONS
Exit tray unit (right tray) specifications
* The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper. Envelopes, tab paper, and glossy paper cannot be output.
Stand/1x500 sheet paper drawer specifications
ModelMX-TRX2
Output methodFace-down output
Output capacity100 sheets (using SHARP-recommended 8-1/2 x 11 or A4 paper)
Dimensions
When tray is folded up:
11-3/8 (W) x...

11
SPECIFICATIONS
Stand/2x500 sheet paper drawer specifications
Large capacity tray specifications*
* A stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer is required to connect the large capacity tray to the machine.
ModelMX-DEX9
Paper sizes11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
7-1/4 x 10-1/2R, A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR
Paper weightPlain paper (16 lbs. to 28 lbs. (60g/m2 to 105g/m2)), heavy paper (28lbs. bond to 110 lbs....

12
SPECIFICATIONS
Finisher specifications
*1 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper.
*2 Up to 10 envelopes can be output.
*3 The height of the sheets must not exceed 2-51/64 (71 mm).
*4 The height of the sheets must not exceed 1-13/32 (35.5 mm).
*5 The maximum number of sheets for stapling assumes a paper weight of 24 lbs. (90g/m
2) and includes two cover sheets of 28...

13
SPECIFICATIONS
Finisher (large stacker) specifications*1
*1 Paper pass unit and stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer are required to connect the finisher (large 
stacker) to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (8-1/2 x 11(A4)) can be...