Sharp Lc32lb370u Maintenance Manual
Have a look at the manual Sharp Lc32lb370u Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
17 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Coaxial (good) 1Make sure that your TV’s power cord is unplugged and all connected equipment is turned off. 2Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box. 3Connect a coaxial cable (not provided) to the ANT / CABLE jack on the back of your TV and to the coaxial out jack on the cable or satellite box. 4Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box. 5Press INPUT to open the INPUT SOURCE list. 6Press S or T to highlight TV, then press ENTER. 7If you cannot tune to channels you know exist, scan for channels. See “Automatically scanning for channels” on page48. Notes • Use a coaxial cable to eliminate interference and noise from radio waves. • Do not bundle the coaxial cable with the power cord or other cables. Cable or satellite box Back of TV Coaxial cable connector ANT / CABLE jack On your TV Coaxial cable
18 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Connecting an antenna or cable TV (no box) 1Make sure that your TV’s power cord is unplugged and all connected equipment is turned off. 2Connect a coaxial cable (not provided) to the ANT / CABLE jack on the back of your TV and to the antenna or cable TV wall jack. 3Plug your TV’s power cord into a power outlet, then turn on your TV. 4Press INPUT to open the INPUT SOURCE list. 5Press S or T to highlight TV, then press ENTER. 6If you cannot tune to channels you know exist, scan for channels. See “Automatically scanning for channels” on page48. Coaxial cable Antenna or cable TV (no box) Back of TV Coaxial cable connector ANT / CABLE jack On your TV Notes • Use a coaxial cable to eliminate interference and noise from radio waves. • Do not bundle the coaxial cable with the power cord or other cables. • If the antenna is not installed correctly, contact qualified service personnel to correct the problem. • If the signal level for a channel is weak, the picture may be distorted. Adjust the antenna or use a highly directional outdoor or set-top antenna with a built-in amplifier. • If the picture quality is good on some channels and poor on others, the problem may be caused by a poor or weak signal from the broadcaster or cable TV provider. • If you connect to cable or satellite TV without a set-top box and experience poor picture quality, you may need to install a set-top box to improve signal reception and picture quality. Contact your cable or satellite TV provider about upgrading to a set-top box. • Many high-definition (HD) channels upscale standard-definition (SD) content. The picture displayed on your TV is still displayed as SD, thus the picture quality will not be as clear or crisp as it would be if the content was originally recorded in HD.
19 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Connecting a DVD or Blu-ray player Many DVD or Blu-ray players have more than one connection type. To get the best video, you should use the best connection type available. For more information, see “What connection should I use?” on page13. HDMI (best) 1Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off. 2Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your T V and to the HDMI OUT jack on the DVD or Blu-ray player. 3Plug your TV’s power cord into a power outlet, then turn on your TV and the DVD or Blu-ray player. 4Press INPUT to open the INPUT SOURCE list. 5Press S or T to highlight HDMI 1, HDMI 2, or HDMI 3, then press ENTER. Note An HDMI cable carries both audio and video. You do not need to use any audio cables. HDMI cable HDMI cable connector HDMI jack On your TVSide of TV DVD or Blu-ray player
20 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Component video (better) 1Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off. 2Connect a component video cable (not provided) to the Y/VIDEO, P B, and PR jacks on the back of your T V and to the COMPONENT OUT jacks on the DVD or Blu-ray player. 3Connect an audio cable (not provided) to the L and Raudio jacks on the back of your TV and to the L and R AUDIO OUT jacks on the DVD or Blu-ray player. 4Plug your TV’s power cord into a power outlet, then turn on your TV and the DVD or Blu-ray player. 5Press INPUT to open the INPUT SOURCE list. 6Press S or T to select Component, then press ENTER. Note Cables are often color-coded to match color-coded jacks. Important •The Y/VIDEO, P B, and PR video jacks (used to connect a component video device) share the L and R audio jacks with the Y/VIDEO jack (used to connect an AV device). You can only connect one component video or AV device at a time. We suggest upgrading to HDMI if your cable or satellite box supports it. • When you connect the audio using the LandR audio jacks, the audio output is analog. Back of TVAudio cable Component video cableDVD or Blu-ray player Component video cable connectorsAudio cable connectors Component video jacksAnalog audio jacks On your TV
21 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV AV (composite video) (good) 1Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off. 2Connect an AV cable (not provided) to the Y/VIDEO jack and L and R audio jacks on the back of your TV and to the AV OUT jacks on the DVD or Blu-ray player. 3Plug your TV’s power cord into a power outlet, then turn on your TV and the DVD or Blu-ray player. 4Press INPUT to open the INPUT SOURCE list. 5Press S or T to select AV, then press ENTER. Notes • Cables are often color-coded to match color-coded jacks. • The yellow video connector on the AV cable connects to the green Y/VIDEO jack. Important •The Y/VIDEO, P B, and PR video jacks (used to connect a component video device) share the L and R audio jacks with the Y/VIDEO jack (used to connect an AV device). You can only connect one component video or AV device at a time. We suggest upgrading to HDMI if your cable or satellite box supports it. • When you connect the audio using the LandR audio jacks, the audio output is analog. AV c a b l e Back of TV AV c a b l e connector AV jac kAudio cable connectors Analog audio jacksDVD or Blu-ray player On your TV
22 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Connecting a game console HDMI (best) 1Make sure that your TV’s power cord is unplugged and the game console is turned off. 2Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your T V and to the HDMI OUT jack on the game console. 3Plug your TV’s power cord into a power outlet, then turn on your TV. 4Turn on the game console, then set it to the correct output mode. For more information, see the documentation that came with the console. 5Press INPUT to open the INPUT SOURCE list. 6Press S or T to highlight HDMI 1, HDMI 2, or HDMI 3, then press ENTER. Note An HDMI cable carries both audio and video. You do not need to use any audio cables. HDMI cable connector HDMI jackSide of TV HDMI cableGame console On your TV
23 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Component video (better) 1Make sure that your TV’s power cord is unplugged and the game console is turned off. 2Connect the video and audio connectors on the component video cable (not provided) to the Y/VIDEO, P B, and PR video jacks and L and Raudio jacks on the back of your TV and to the component jack(s) on the game console. 3Plug your TV’s power cord into a power outlet, then turn on your TV. 4Turn on the game console, then set it to the correct output mode. For more information, see the documentation that came with the console. 5Press INPUT to open the INPUT SOURCE list. 6Press S or T to select Component, then press ENTER. Note Cables are often color-coded to match color-coded jacks. Important • Your game console may require a special component video cable. See the documentation that came with your game console or check the manufacturer’s website. •The Y/VIDEO, P B, and PR video jacks (used to connect a component video device) share the L and R audio jacks with the Y/VIDEO jack (used to connect an AV device). You can only connect one component video or AV device at a time. We suggest upgrading to HDMI if your game console supports it. • When you connect the audio using the LandR audio jacks, the audio output is analog. Game console Back of TVConsole-specific component video and audio cable On your TV Component video cable connectorsAnalog audio cable connectors Component video jacksAnalog audio jacks
24 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV AV (composite video) (good) 1Make sure that your TV’s power cord is unplugged and the game console is turned off. 2Connect the video and audio connectors on the game console’s AV cable (not provided) to the Y/VIDEO jack and L and R audio jacks on the back of your TV and to the composite jack(s) on the game console. 3Plug your TV’s power cord into a power outlet, then turn on your TV. 4Turn on the game console, then set it to the correct output mode. For more information, see the documentation that came with the console. 5Press INPUT to open the INPUT SOURCE list. 6Press S or T to select AV, then press ENTER. Notes • Cables are often color-coded to match color-coded jacks. • The yellow video connector on the AV cable connects to the green Y/VIDEO jack. Important • Most game consoles come with a special AV cable. See the documentation that came with your game console or check the manufacturer’s Web site. •The Y/VIDEO, P B, and PR video jacks (used to connect a component video device) share the L and R audio jacks with the Y/VIDEO jack (used to connect an AV device). You can only connect one component video or AV device at a time. We suggest upgrading to HDMI if your game console supports it. • When you connect the audio using the LandR audio jacks, the audio output is analog. Game console Console-specific AV cable Back of TV AV ca bl e connectorAnalog audio cable connectors AV j a c k An a l o g audio jacks On your TV
25 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Connecting a computer 1Make sure that your TV’s power cord is unplugged and the computer is turned off. 2Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your T V and to the HDMI OUT jack on the computer. 3Plug your TV’s power cord into a power outlet, then turn on your TV and the computer. 4Press INPUT to open the INPUT SOURCE list. 5Press S or T to highlight HDMI 1, HDMI 2, or HDMI 3, then press ENTER. 6Adjust the display properties on the computer, if necessary. HDMI cable Side of TV HDMI cable connector HDMI jackOn your TV
26 LC-32LB370U/LC-50LB370U Sharp 32"/50" LED TV Connecting a USB flash drive 1Plug a USB flash drive into the USB port on the side of your TV. 2If your T V is turned on when you connect the USB flash drive, press S or T to select Ye s in the message that appears, then press ENTER. The PHOTOS menu opens. OR If you switch to a different video input source after you plug in the USB flash drive and want to switch back to the drive, press INPUT to open the INPUT SOURCE list, press S or T to select USB (Photos), then press ENTER. The PHOTOS menu opens. Caution Do not remove the USB flash drive or turn off the TV while using the USB flash drive. You may lose data or damage the USB flash drive. Note The PHOTOS viewer only supports JPEG format images (with “.jpg” file extensions) and not all JPEG files are compatible with your TV. For more information, see “Using a USB flash drive” on page42. USB flash drive Side of TV