Sharp Lc 46d65e Operation Manual

							
Connecting a PC
NOTEThis TV has only limited PC compatibility, correct operation 
can only be guaranteed if the video card conforms exactly 
to the VESA 60 Hz standard. Any variations from this 
standard will result in picture distortions.•
CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS
POWER SETTING P O W R 0 _ _ _ POWER OFF
INPUT SELECTION A I T G D _ _ _ _ INPUT SWITCHING (TOGGLE)I T V D _ _ _ _ TV (CHANNEL FIXED)
I D T V _ _ _ _ DTV (CHANNEL FIXED)
I A V D * _ _ _ EXT1–4, 8 (1–4, 8), HDMI1–3  (5–7)
CHANNEL D C C H * * _ _ TV DIRECT CHANNEL (1–99) C H U P _ _ _ _ CHANNEL UP
C H D W _ _ _ _ CHANNEL DOWND T V D * * * _ THREE DIGIT DTV DIRECT  CHANNEL (1–999) (Non-Nordic 
countries)
D T V D * * * * FOUR DIGIT DTV DIRECT  CHANNEL (1–9999) (Nordic 
countries only)
D T U P _ _ _ _ DTV CHANNEL UP
D T D W _ _ _ _ DTV CHANNEL DOWN
INPUT SELECTION B I N P 1 0 _ _ _ EXT1 (Y/C)
I N P 1 1 _ _ _ EXT1 (CVBS)
I N P 1 2 _ _ _ EXT1 (RGB)
I N P 2 0 _ _ _ EXT2 (Y/C)
I N P 2 1 _ _ _ EXT2 (CVBS)
I N P 2 2 _ _ _ EXT2 (RGB)
AV MODE SELECTION A V M D 0 _ _ _ TOGGLE
A V M D 1 _ _ _ STANDARD
A V M D 2 _ _ _ MOVIE
AVM D 3 _ _ _ GAME
A V M D 4 _ _ _ USER
A V M D 5 _ _ _ DYNAMIC (Fixed)
A V M D 6 _ _ _ DYNAMIC
AVMD7 _ _ _PC
A V M D 8 _ _ _ x.v.Colour
A V M D ? ? ? ? 1–8
VOLUME V O L M * * _ _ VOLUME (0–60)
CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS
POSITION H P O S * * * _ H-POSITION (AV/PC) V P O S * * * _ V-POSITION (AV/PC)
C L C K * * * _ CLOCK (0–180) P H S E * * _ _ PHASE (0–40)
WIDE MODE W I D E 0 _ _ _ TOGGLE (AV) W I D E 1 _ _ _ NORMAL (AV)
W I D E 2 _ _ _ ZOOM 14:9 (AV)
W I D E 3 _ _ _ PANORAMA (AV)
W I D E 4 _ _ _ FULL (AV)
W I D E 5 _ _ _ CINEMA 16:9 (AV)
W I D E 6 _ _ _ CINEMA 14:9 (AV)
W I D E 7 _ _ _ NORMAL (PC)
W I D E 8 _ _ _ CINEMA (PC)
W I D E 9 _ _ _ FULL (PC)
W I D E 1 0 _ _ DOT by DOT (AV/PC)
W I D E 1 1 _ _ UNDERSCAN (AV)
MUTE M U T E 0 _ _ _ TOGGLE M U T E 1 _ _ _ MUTE ON
M U T E 2 _ _ _ MUTE OFF
SURROUND A C S U 0 _ _ _ SURROUND TOGGLE A C S U 1 _ _ _ SURROUND ON
A C S U 2 _ _ _ SURROUND OFF
AUDIO CHANGE A C H A _ _ _ _ TOGGLE
SLEEP TIMER O F T M 0 _ _ _ OFF O F T M 1 _ _ _ SLEEP TIMER 30 MIN
O F T M 2 _ _ _ SLEEP TIMER 1 HOUR
O F T M 3 _ _ _ SLEEP TIMER 1 HOUR 30 MIN
O F T M 4 _ _ _ SLEEP TIMER 2 HOUR
O F T M 5 _ _ _ SLEEP TIMER 2 HOUR 30 MIN
TEXT T E X T 0 _ _ _ TEXT OFF T E X T 1 _ _ _ TEXT ON (TOGGLE)
DCPG***_
DIRECT PAGE JUMP (100–899)
PC compatibility chart
Resolution Horizontal 
Frequency Vertical 
Frequency Analogue (D-
Sub) Digital (HDMI) VESA 
Standard
VGA 640 g 480 31.5 kHz 60 Hz
✔✔✔
SVGA 800 g 600 37.9 kHz 60 Hz
✔✔✔
XGA 1,024 g 768 48.4 kHz 60 Hz
✔✔✔
WXGA 1,360 g 768 47.7 kHz 60 Hz
✔✔✔
SXGA 1,280 g 1,024 64.0 kHz 60 Hz
✔✔✔
SXGA+ 1,400 g 1,050 65.3 kHz 60 Hz
✔✔
VGA, SVGA, XGA, WXGA, SXGA and SXGA+ are 
registered trademarks of International Business 
Machines Corporation.
RS-232C command list
 39
 
						

							
Appendix
Troubleshooting
Problem Possible Solution
No power.
•
Check if you pressed B on the remote control unit.
If the indicator on the TV lights up red, press  B.
Is the AC cord disconnected?
Check if you pressed  a on the TV.
•
•
•
The TV cannot be operated.
• External influences such as lightning, static electricity, etc., may cause improper operation. In this 
case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging 
it in after one or two minutes.
•
Remote control unit does not operate.
•
Are batteries inserted with polarity (e, f ) aligned?
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminating to the remote control sensor?
•
•
•
•
Picture is cut off.
• Is the image position correct?
Are screen mode adjustments (WIDE MODE) such as picture size made correctly? (Pages 30 
and 36)
•
•
Strange colour, light colour, or dark 
colour, or colour misalignment.
• Adjust the picture tone.
Is the room too bright? The picture may look dark in a room that is too bright.
Check the “Colour System” setting (Pages 28 and 33).
•
•
•
Power is suddenly turned off.
• The TV’s internal temperature has increased.
Remove any objects blocking the vent or clean.
Is the “Sleep Timer” set? Select “Off” from the “Sleep Timer” menu (Page 26).
Is “No Signal Off” or “No Operation Off” activated?
•
•
•
No picture.
• Are connections to external equipment correct? (Pages 15–17)
Is the input signal type selected correctly after connection? (Page 33)
Is the correct input source selected? (Page 10)
Is a non-compatible signal being input? (Page 39)
Is the picture adjustment correct? (Pages 24–25)
Is the antenna connected properly? (Page 8)
Is “On” selected in “Audio Only”? (Page 31)
•
•
•
•
•
•
•
No sound.
• Is the volume too low?
Make sure that headphones are not connected.
Check if you pressed e on the remote control unit.
Is the proper item selected in the “PC Audio Select” menu when connecting d\
evices to the 
HDMI2 terminal or the EXT4 terminal? (Pages 16 and 36)
•
•
•
•
The TV sometimes makes a cracking 
sound.
• This is not a malfunction. This happens when the cabinet slightly expand\
s and contracts 
according to changes in temperature. This does not affect the TV’s performance.
•
Cautions regarding use in high and low temperature environmentsWhen the TV is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. 
This is not a malfunction, and the TV will recover when the temperature returns to normal.
Do not leave the TV in a hot or cold location. Also, do not leave the TV\
 in a location exposed to direct sunlight or near a 
heater, as this may cause the cabinet to deform and the LCD panel to malfuncti\
on.
Storage temperature: 
e5 °C to  e35 °C.
•
•
Information on the software license for this product
Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by 
SHARP or by third parties.
Software developed by SHARP and open source software The copyrights for the software components and various relevant documents included with this product that were developed 
or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant 
laws. This product also makes use of freely distributed software and software components whose copyrights are held by 
third parties. These include software components covered by a GNU General Public License (hereafter GPL), a GNU Lesser 
General Public License (hereafter LGPL) or other license agreement.
Obtaining source code Some of the open source software licensors require the distributor to provide the source code with the executable software 
components. GPL and LGPL include similar requirements. For information on obtaining the source code for the open source 
software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website:
http://www.sharp-eu.com/gpl/
We are unable to answer any questions about the source code for the open source software. The source code for the 
software components whose copyrights are held by SHARP is not distributed.
Acknowledgements The following open source software components are included in this product:
• linux kernel • busy box • uClibc • zlib • libpng • libjpeg
 40
 
						

							
Appendix
Download Setup
Digital Setup
Message List
Information
Go to “MENU” > “Setup” > “Reset”.
Press c/d  to select “Yes”, and then press  OK.
“Now, TV will restart automatically. OK?” displays on 
the screen.
Press  c/d  to select “Yes”, and then press  OK.“Now initialising...” displays on the screen and blinks.
After the reset has completed, the power shuts 
off and then comes back on. The screen will have 
returned to its original settings.
Now initialising...
1
2
•
3•
•
Reset
Setup
Identification
Setup
Receiver Report
Information
Display reports regarding failures and changes for 
timer settings.
Reset
If complex adjustments are made so that the settings 
cannot be restored to normal, you can reset the 
settings to the factory preset values.
Searching for updates*
All countries except UK and Sweden are set to “No” 
for this function.
The TV automatically determines whether a new 
software version is available when the TV is in standby 
mode. *
Updating your TV via DVB-T
Ensure that your TV software version is always up to 
date. From time to time SHARP will make updated TV 
base software and DVB software available.
Yes:  Automatically searches for new software updates 
available when the TV is in standby mode.
No:  Does not search for update information.
Now:  Checks if there is new software immediately.
Downloading the software
You can select the method of update.
If the software is updated, the confirmation 
message “New download information has been 
detected.” appears.
If the TV receives the update service while in standby 
mode, a confirmation message displays after turning 
on the power.
Follow the screen prompts.
1
•
2
Yes:  Starts downloading immediately. It takes 
approximately one hour to update. You cannot carry 
out other operations while downloading.
Cancels the download by pressing  OK on the remote 
control unit when “Discontinue” is displayed on the 
screen during the update.
No:  Starts downloading automatically several minutes 
after entering standby mode.
•
When new software is detected, you can confirm the 
update information and download the software from 
“Message List”.
NOTE
When the TV succeeds at downloading new software, 
the message is updated in the “Message List” of the 
“Information” menu.
The software update will not be carried out if there is no 
new software available at the specified download time.
•
•
Identification
CLEARING THE PIN
Go to “MENU” > “Setup”.
Press 
a/b  to select “Auto Installation”, 
“Programme Setup”, “Child Lock” or “Reset”, 
and then press  OK. The PIN input window will 
display.
Press and hold both  Pr  and  ik on the TV 
simultaneously until the message appears on 
the screen.1
2
3
You can check the TV ID on the screen for reporting to 
customer service.
NOTE
The TV must remain in standby mode for download. Do not 
turn off the power using  a on the TV.
Updating the software may take some time.
•
•
 41
Item
Item
 
						

							
Appendix
Specifications
Item46
o LCD COLOUR TV, 
Model: LC-46D65E, LC-46DH65E, 
LC-46DH65S 52
o LCD COLOUR TV, 
Model: LC-52D65E, LC-52DH65E, 
LC-52DH65S
LCD panel 46o Advanced Super View & BLACK TFT LCD 52 o Advanced Super View & BLACK TFT LCD
Resolution 2,073,600 pixels (1,920 g 1,080)
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV Function TV-Standard Analogue CCIR (B/G, I, D/K, L/L’)
Digital DVB-T (2K/8K OFDM)
Receiving 
Channel VHF/UHF E2–E69 ch, F2–F10 ch, I21–I69 ch, IR A–IR J ch (Digital: IR\
 A ch–E69 ch)
CATV Hyper-band, S1–S41 ch
TV-Tuning System Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Brightness 450 cd/m
2
Backlight life 60,000 hours (when “Backlight” is set to the default position)
Viewing angles H: 176°, V: 176°
Audio amplifier 10 W g 2
Speaker (40 mm g 110 mm)  g 2
Terminals Antenna UHF/VHF 75 q Din type (Analogue & Digital)
RS-232C D-Sub 9 pin male connector
EXT1 SCART (AV input, Y/C input, RGB input, TV output)
EXT2 SCART (AV input/monitor output, Y/C input, AV Link, RGB input)
EXT3 COMPONENT IN: Y/P
B(CB)/PR(CR), RCA pin (AUDIO R/L)
EXT4 15 pin mini D-sub, Ø 3.5 mm jack*
HDMI1 (EXT5) HDMI
HDMI2 (EXT6) HDMI, Ø 3.5 mm jack*
HDMI3 (EXT7) HDMI
EXT8 RCA pin (AV input)
USB USB 2.0
DIGITAL AUDIO OUTPUT Optical S/PDIF Digital audio output
C. I. (Common Interface) EN50221, R206001
OUTPUT RCA pin (AUDIO R/L)
Headphones Ø 3.5 mm jack (Audio output)
OSD language Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian,  Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slo\
vene, Spanish, 
Swedish, Turkish, Ukrainian
Power Requirement AC 220–240 V, 50 Hz
Power Consumption 
(Method IEC62087)LC-46D65E217 W (0.5 W Standby) LC-52D65E266 W (0.5 W Standby) 
LC-46DH65E 
LC-46DH65S220 W (0.5 W Standby) LC-52DH65E 
LC-52DH65S269 W (0.5 W Standby) 
Weight 21.2 kg (Without stand), 24.2 kg (With stand) 24.7 kg (Without stand), 28.3 kg (With stand)
Operating temperature 0 °C to e40 °C
The HDMI2 and EXT4 terminals can both use the same audio input terminal.\
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for produc t 
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There  may be some 
deviations from these values in individual units.
NOTERefer to the inside back cover for dimensional drawings.
Optional accessory
*
•
•
The listed optional accessories are available for this LCD 
colour TV. Please purchase them at your nearest shop.
Additional optional accessories may be available in the near 
future. When purchasing, please read the newest catalogue for 
compatibility and check the availability.
•
No. Part name Part number
1 Wall mount bracket 
(LC-46D65E, LC-46DH65E, 
LC-46DH65S, LC-52D65E, 
LC-52DH65E, LC-52DH65S) AN-52AG4
 42
 
						

							
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use t\
he ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires 
proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within\
 the EU states may return their used 
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local 
retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these se\
parately 
beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery 
and recycling and thus prevent potential negative effects on the environment and human health which could otherwise 
arise due to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t 
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back\
 of the product. You might be charged for 
the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local 
collection facilities.
For Spain: Please contact the established collection system or your loca\
l authority for take-back of your used 
products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
Attention: Your product 
is marked with this 
symbol. It means that 
used electrical and 
electronic products 
should not be mixed 
with general household 
waste. There is a 
separate collection 
system for these 
products.
End of life disposal
Information on Battery Disposal
For EU: The crossed-out wheeled bin implies that used batteries should not be put to t\
he general household waste! 
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with 
legislation. Please contact your local authority for details on the coll\
ection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for corr\
ect method of disposal of the used battery.
 43
 
						

							
Rating table for Child Lock
AGE
456789101112131415161718
Universal viewing ✔——————————————
Parental approval pref. ✔✔✔✔✔ ——————————
X-rated ✔✔✔✔✔✔✔✔✔✔✔✔✔✔✔
Universal viewing Parental approval pref. X-rated
Universal viewing ———
Parental approval pref. ✔——
X-rated ✔✔ —
User-
adjusted rating
Broadcasted 
rating
User-
adjusted rating Broadcasted 
rating
 44
 
						

							 
(1113.0 )/ [1252.0]
 
(1113,0 )/ [1252,0]
 
(1023.4 )/ [1157.0]
 
(1023,4 )/ [1157,0]
[54.5]
[54,5 ] (52.0)
(52,0)
[145.0]
[145,0 ] (174.3)
(174,3)
[111.9]
[111,9] (106.6)
(106,6)
[95.6]
[95,6 ] (101.4)
(101,4)
 
(704.0 )/ [796.0]
 
(704,0 )/ [796,0]  
(756.0 )/ [851.0]
 
(756,0 )/ [851,0]
400.0
400,0
400.0
400,0
295.0
295,0
550.0
550,0
 
(575.6 )/ [651.0]
 
(575,6 )/ [651,0]
 
(429.0 )/ [476.0]
 
(429,0 )/ [476,0]
SPECIAL NOTE FOR USERS IN THE U.K.The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the 
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked  or 
 and of the same rating as above, 
which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains 
plug and fit an appropriate type.
DANGER:The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a 
safe manner. 
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric 
shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings 
identifying the terminals in your plug, proceed as follows:
•  The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
•  The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
•  If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
•  The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.(    ) : LC-46D65E/46DH65E/46DH65S
[    ] : LC-52D65E/52DH65E/52DH65S
  
 : LC-46D65E/46DH65E/46DH65S
    LC-52D65E/52DH65E/52DH65S
 
						

							LC-46D65E
LC-46DH65E
LC-46DH65S
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR DE CRISTAL LÍQUIDO
Printed in Spain
Gedruckt in Spanien
Imprimé en Espagne
Stampato in Spagna
Gedrukt in Spanje
Impreso en España
Impresso no Espanha
LC-46D65E/LC-52D65E
LC-46DH65E/LC-52DH65E
LC-46DH65S/LC-52DH65S
OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D’EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO / 
MANUAL DE OPERAÇÃO
D808WJZZ1
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
ESPAÑOL
TINS-D808WJZZ08P09-SP-NG
PIN
SHARP ELECTRÓNICA ESPAÑA S.A.
Polígono Industrial Can Sant Joan
Calle Sena s/n
08174 SANT CUGAT DEL VALLÉS
BARCELONA (ESPAÑA)
SHARP CORPORATION
LC-52D65E
LC-52DH65E
LC-52DH65S
PORTUGUÊS
: LC-46D65E/LC-52D65E
: LC-46DH65E/LC-52DH65E
: LC-46DH65S/LC-52DH65S