Sharp Lc 46d65e Operation Manual

							
Connecting external devices
Inserting a CA Card
In order to receive coded digital stations, a Common 
Interface Module (CI Module) and a CA Card must be 
inserted in the CI slot of the TV (Page 8).
The CI Module and the CA Card are not supplied 
accessories. They are usually available from your 
dealers.
Inserting the CA Card into the CI Module
With the side with the gold coloured contact 
chip facing the side of the CI Module marked 
with the provider’s logo, push the CA Card 
into the CI Module as far as it will go. Note the 
direction of the arrow printed on the CA Card.
Inserting the CI Module in the CI slot
Carefully insert the CI 
Module in the CI slot 
with the contact side 
forward. The logo on 
the CI Module must be 
facing outward from the 
rear of the TV. Do not use 
excessive force. Make 
sure the module is not 
bent in the process.
1
2
Checking CI Module information
NOTEMake sure that the CI Module is properly inserted.
This menu is only available for digital stations.
Press MENU  and the “MENU” screen displays.
Press  c/d  to select “Digital Setup”.
The content of this menu depends on the provider of 
the CI Module.
Press  a/b  to select “CI Menu”, and then press 
OK .
•
•
1
2
•
3
 19
Module
General information on CI Module displays.
Menu
Adjustment parameters of each CA Card displays.
Enquiry
You can input numerical values such as passwords 
here.
NOTE
The content of each screen depends on the provider of 
the CI Module.
E
E
E
•
 
						

							
AQUOS LINK
Controlling HDMI devices using AQUOS LINK
What is AQUOS LINK?Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you 
can interactively operate compatible system devices (AV amplifier, DVD player/recorder, 
Blu-ray player/recorder) using a single remote control unit.
NOTE
AQUOS LINK-compatible AQUOS AUDIO speaker system and AQUOS Recorder are scheduled 
to be on sale after the release of this TV (as of September 2008).
What you can do with AQUOS LINK
One Touch Recording (DTV only)
You do not have to search for the remote control unit of your recording device. Press the 
REC E or  REC STOP  H buttons inside the flip cover to start/stop recording what you 
see on the recorder.
One Touch Play
When the TV is in standby mode, it will automatically turn on and play back the image 
from the HDMI source.
Single remote control operation
AQUOS LINK automatically recognises the connected HDMI devices and you can 
control the TV and the devices as if using a universal remote control unit.
Operating Title list of external devices
In addition to displaying the TV’s own Timer list (Page 12), you can also call up the 
external player’s Top menu or AQUOS BD Player’s/AQUOS Recorder’s Title list provided 
that the devices support AQUOS LINK.
Multiple control of HDMI devices
You can select which HDMI device to operate using the  OPTION button.
NOTE
When you use AQUOS LINK, make sure to use a certified HDMI cable.
Point the remote control unit toward the TV, not to the connected HDMI device.
Video noise may occur depending on the type of HDMI cable used. Make sure to use a certified 
HDMI cable.
Up to three HDMI recording devices, one AV amplifier and two players can be connected using 
this system.
These operations affect the HDMI device selected as the current external source. If the device 
does not operate, turn on the device and select the appropriate external source using  b.
When you insert/remove HDMI cables or change connections, turn on all connected HDMI 
devices before turning on the TV. Confirm that picture and audio are correctly output by selecting 
“HDMI1”, “HDMI2” or “HDMI3” from the “INPUT SOURCE” menu.
•
✔
✔
✔
✔
✔
•
•
•
•
•
•
AQUOS LINK connection
First connect the AQUOS AUDIO speaker system or an AQUOS BD Player/AQUOS\
 Recorder that supports the 
HDMI CEC protocol.
NOTE
Refer to the operation manual of the device to be connected for further \
details.
After unplugging connection cables or changing the connection pattern, turn on the power of the TV after all relevant devices’ 
power have been turned on. Change the external input source by pressing 
b, select the appropriate external source and 
verify the audiovisual output.
The cables illustrated in the following explanation are commercially available items.
•
•
•
 20
 
						

							
AQUOS LINK
AQUOS LINK Control
Set to “On” to enable HDMI CEC functions. When 
turning on the power while “AQUOS LINK Control” is 
set to “On”, the connected HDMI devises’ power will 
be turned on in conjunction with the TV.Press  MENU  and the “MENU” screen displays.
Press  c/d  to select “Option”.
Press  a/b  to select “AQUOS LINK Setup”, and 
then press  OK.
Press  a/b  to select “AQUOS LINK Control”, 
and then press  OK.
Press  c/d  to select “On”, and then press  OK.
Auto Power On
If this is activated, the One Touch Play function 
is enabled. While the TV is in standby mode, it 
automatically turns on and plays back the image from 
the HDMI source.
Repeat steps 1 to 3 in  AQUOS LINK Control.
Press  a/b  to select “Auto Power On”, and then 
press  OK.
Press  c/d  to select “On”, and then press  OK.
NOTE
The factory default for this item is “Off”.
1
2
3
4
5
1
2
3
•
AQUOS LINK Setup
Selecting Recorder
Here, you can select a recorder for the recording from 
several connected recorders. Repeat steps 1 to 3 in  AQUOS LINK Control.
Press  a/b  to select “Selecting Recorder”, and 
then press  OK.
Select the recorder, and then press  OK.
NOTE
If you have connected the AQUOS AUDIO speaker system 
between the TV and an AQUOS Recorder, the external 
source’s indication changes (e.g. from “HDMI1” to “HDMI1 
(Sub)”).
Using Genre Info.
This function allows you to automatically switch to 
the appropriate sound mode depending on the genre 
information included the digital broadcast. Repeat steps 1 to 3 in  AQUOS LINK Control.
Press  a/b  to select “Using Genre Info.”, and 
then press  OK.
Press  c/d  to select “On”, and then press  OK.
1
2
3
•
1
2
3
Connecting an AQUOS BD 
Player/AQUOS Recorder onlyConnecting an AQUOS BD Player/AQUOS Recorder via 
the AQUOS AUDIO speaker system
 21
HDMI-certified cable
AQUOS AUDIO 
speaker system
HDMI-certified cable
AQUOS BD Player/ AQUOS Recorder
Optical audio 
cable
AQUOS BD Player/ 
AQUOS Recorder
HDMI-certified cable
 
						

							
AQUOS LINK
Open the remote control unit’s flip cover, and 
then press OPTION.
Press  a/b  to select “Setup Menu”, and then 
press  OK.
NOTE
If a connected device does not have this function or the 
device is in a status where the menu cannot be displayed 
(recording, entering standby, etc.), this function may not be 
available.
Playback of titles using AQUOS LINK
This section explains how to play back a title in the 
AQUOS BD Player/AQUOS Recorder. Open the remote control unit’s flip cover, and 
then press  OPTION.
Press  a/b  to select “Top Menu/Title List”, and 
then press  OK.
The linked recorder now powers on and the TV 
automatically selects the appropriate external input 
source.
The title list data from the connected AQUOS BD 
Player/AQUOS Recorder displays.
Select the title with  a/b /c /d , and then press 
PLAY  I.
Selecting media type for CEC-compatible 
recorder
If your recorder has multiple storage media, select the 
media type here.
Open the remote control unit’s flip cover, and 
then press  OPTION.
Press  a/b  to select “Media change”, and then 
press  OK.
Select the desired medium, such as DVD 
recorder or HDD. The media type changes every 
time you press  OK.
HDMI device selection
If multiple HDMI devices are connected in a daisy 
chain, you can specify which device to control here.
Open the remote control unit’s flip cover, and 
then press  OPTION.
Press  a/b  to select “Model select”, and then 
press  OK. The HDMI device changes every time 
you press  OK.
Recording via the AQUOS Recorder EPG 
(only for recorders)
You can call up the CEC-compatible recorder’s EPG 
and preset timer recordings using the TV’s remote 
control unit.
Open the remote control unit’s flip cover, and 
then press  OPTION.
Press  a/b  to select “Recorder EPG”, and then 
press  OK.
The external input source switches and the recorder’s 
EPG is displayed.
Select the programme to record.Refer to the operation manual of the recorder for details.
1
2
•
1
2
•
•
3
1
2
3
1
2
1
2
•
3•
Operating an AQUOS LINK device
AQUOS LINK allows you to operate the HDMI-
connected device with a single remote control unit.
Open the remote control unit’s flip cover.
Press  PLAY  I to start playback of a title.
See the right column, section “ Playback of titles 
using AQUOS LINK ” if you want to start playback 
using the list of the titles of the AQUOS BD Player/
AQUOS Recorder.
Press  FWD J  to fast forward.
Press  REV G  to reverse.
Press  STOP H  to stop.
Press  B to turn the HDMI-connected device on/off.
Listening with the AQUOS AUDIO speaker system
You can choose to listen to the TV sound only from the 
AQUOS AUDIO speaker system.
Open the remote control unit’s flip cover, and 
then press  OPTION.
AQUOS LINK Menu
Recorder EPG 
Top Menu/Title List 
Media change 
By AQUOS AUDIO SP 
By AQUOS SP  Sound mode change 
Setup Menu 
Model select 
Press  a/b  to select “By AQUOS AUDIO SP”, 
and then press  OK.
The sound from the TV speaker and headphone 
terminal is silenced and only the sound from the 
AQUOS AUDIO speaker system is audible.
Listening with the AQUOS TV speaker system
You can choose to listen to the TV sound only from the 
AQUOS TV speaker system.
Open the remote control unit’s flip cover, and 
then press  OPTION.
Press  a/b  to select “By AQUOS SP”, and then 
press  OK.
Manually changing the AQUOS AUDIO 
speaker system’s sound mode
Open the remote control unit’s flip cover, and 
then press  OPTION.
Press  a/b  to select “Sound mode change”.
The sound mode changes every time you press  OK.Refer to the operation manual of the AQUOS AUDIO 
speaker system for details.
Calling up the menu of an external device 
connected with the TV via HDMI
You can call up the menu of an HDMI CEC-compatible 
external device (player, recorder, decoder, etc.) using 
the “Setup Menu” function.
1
2
•
3
1
2
•
1
2
1
2
3
•
 22
 
						

							
Menu operation
1
Picture 
Contrast OPC [Off] 
Brightness
Colour
Tint
Sharpness
Advanced
Reset [+30] 
[0] 
[0] 
[0] 
[0] 
0 
–30 
–30 
–30 
–10  +40 
+30 
+30 
+30 
+10 
Backlight [+14] –16 
+16 
DYNAMIC
ECO
Energy Save
No Signal Off
No Operation Off
Sleep Timer [Off]
[Disable]
[Disable]
Analogue Search
Digital Search
3
2
NOTE“MENU” options differ in the selected input modes, but the operating procedures are the same.
The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from  the actual screens.
Items with  4 cannot be selected for various reasons.
•
•
•
What is the MENU?
You need to call up the OSD to perform settings for the TV. The OSD for the settings is called “MENU”.
The “MENU” enables various settings and adjustments.
The “MENU” can be operated with the remote control unit.
Common operations
•
•
•
Operation without a remote control unit
This function is useful when there is no remote control 
unit within your reach.
Press  MENU  and the “MENU” 
screen displays.
Press  Pr /s  instead of  a/b  
or  i k/l  instead of  c/d  to 
select the item.
Press  b to complete the setting.
NOTE
The “MENU” screen will disappear if left unattended for several 
seconds.
1
2
3
•
About the Guide Display
The Guide Display at the bottom of the screen shows 
operations with the OSD.
OK: Select  : Enter MENU : End 6: Back 
The bar above is an operational guide for the remote 
control unit. The bar will change in accordance with 
each menu setting screen.
 23
Display the MENU  Screen
Exit the MENU  screen Select an item
Press 
MENU  and the “MENU” 
screen displays.
The operation will exit the “MENU” 
screen if you press  END before it is 
completed. Press 
a/b /c /d  to select/adjust the 
desired menu, and adjust the item to 
the desired level, and then press  OK.
Press  6 to return to the previous 
“MENU” page.
Selecting in the MENUE
Selecting optionsE
 
						

							
Basic adjustment
NOTEWhen set to “On”, the TV senses the surrounding light and 
automatically adjusts the backlight brightness. Make sure 
no object obstructs the OPC sensor, which could affect its 
ability to sense surrounding light.
• This TV provides various advanced functions for optimising 
the picture quality.
Film Mode
Active Contrast
DNR
3D-Y/C
Monochrome
Y
G
C
B
M[    0]
[    0]
[    0]
[    0]
[    0]f
30
f 30
f 30
f 30
f 30e30
e 30
e 30
e 30
e 30
Range of OPC
C.M.S.-Hue
This function adjusts the hue of a selected colour using a six-
colour adjustment system.
C.M.S.-Saturation
This function increases or decreases the saturation of a 
selected colour using a six-colour adjustment system.
Colour Temp.
Adjusts the colour temperature to give the best white image.
NOTE“3D-Y/C” may not operate depending on the input signal type or 
when the input signal is noisy.
“3D-Y/C” has even more effect on composite video signals (CVBS).
•
•
Picture Settings
Picture 
Contrast OPC [Off] 
Brightness
Colour
Tint
Sharpness
Advanced
Reset [+30] 
[0] 
[0] 
[0] 
[0] 
0 
–30 
–30 
–30 
–10  +40 
+30 
+30 
+30 
+10 
Backlight [+14] –16 
+16 
DYNAMIC
Film Mode
Automatically detects a film-based source (originally encoded 
at 24 or 25 frames per second, depending on the vertical 
frequency), analyses it and then recreates each still film frame 
for high-definition picture quality.
Active Contrast
Automatically adjusts the contrast of an image according to 
the scene.
DNR
“DNR” (Digital Noise Reduction) produces a clearer image 
(“Off”, “High”, “Middle”, “Low”).
3D-Y/C
Provides high quality images with minimal dot crawl and cross 
colour noise by detecting changes in the image.
Off:
 The brightness is fixed at the value set in “Backlight”.
On:  Automatically adjusts.
On:Display:  Displays the OPC effect on the screen while 
adjusting the brightness of the screen.
OPC
Picture
Automatically adjusts the brightness of the screen.
Adjusts the picture to your preference with the 
following picture settings.
Adjustment items
Selectable items c
 button d button
Backlight The screen dims The screen brightens
Contrast For less contrast For more contrast
Brightness For less brightness For more brightness
Colour For less colour 
intensity For more colour 
intensity
Tint Skin tones become 
purplish Skin tones become 
greenish
Sharpness For less sharpness For more sharpness
Advanced
Picture
High: White with bluish tone.
Mid-High:  Intermediate tone between “High” and “Middle”.Middle: Natural tone.
Mid-Low:  Intermediate tone between “Middle” and “Low”.Low: White with reddish tone.
Standard:  Normal adjustment.
Fast:  Sets the optimum image quality for fast-moving images.
Slow:  Sets the optimum image quality for slow-moving images.
Picture adjustments
Picture
 24
Item
Item
Item
 
						

							
Basic adjustment
NOTEThe item marked with * is available only when selecting 
“HDMI1”, “HDMI2”, “HDMI3” or “EXT4” from the “INPUT 
SOURCE” menu.
The item marked with ** is available only when accepting 
an “x.v.Colour” signal through an HDMI terminal.
For input source “USB”, you can only select “USER (USB)”, 
“DYNAMIC (Fixed)”, “DYNAMIC” and “STANDARD”.
•
•
•
Monochrome
For viewing a colour video in black & white.
Range of OPC
The brightness level range of the OPC sensor’s 
automatic adjustments can be set according to your 
preferences. The adjustment range of the OPC sensor 
can be set to a maximum of 
e16 and a minimum of 
f 16.
Selectable 
items Description
Max. f16 through  e16
Min. f16 through  e16
NOTEThis function is available only when the “OPC” setting is set 
to “On” or “On:Display”.
The maximum setting cannot be set to a smaller number 
than the minimum setting.
The minimum setting cannot be set to a bigger number 
than the maximum setting.
The maximum and minimum settings cannot be set to the 
same number.
Depending on the brightness of the surrounding light, the 
OPC sensor might not operate if the adjustment range is 
small.
AV MODE
“AV MODE” gives you several viewing options to 
choose from to best match the system environment, 
which can vary due to factors like room-brightness, 
type of programme watched or the type of image input 
from external equipment.
Press  AV MODE .
Each time you press  AV MODE, the mode 
changes.
You can also switch the mode on the “Picture” and 
“Audio” menu screen by pressing  AV MODE.
•
•
•
•
•
1
2
•
Audio Settings
Audio
Balance Treble
Surround
Reset [   0]
[   0]
–15
L +15
R
[Off]
Bass[   0] –15
+15
DYNAMIC
 
STANDARD:
 For a highly defined image in a normally 
bright room.
MOVIE:  For viewing a movie in a darkened room.
GAME:  For playing of video games.
PC*:  For PC.
x.v.Colour**:  Produce realistic colour on the TV screen 
unlike any other signal.
USER:  Allows you to customise settings as desired. You 
can set the mode for each input source.
DYNAMIC (Fixed):  For a clear-cut image emphasising 
high contrast for sports viewing (The “Picture” and 
“Audio” settings cannot be adjusted).
DYNAMIC:  For a clear-cut image emphasising high 
contrast for sports viewing.
Audio adjustment
Audio
Surround
Audio
This function allows you to enjoy realistic live sound. You can adjust the sound quality to your preference 
with the following settings.
Selectable  items c
 button d button
Treble For weaker treble For stronger treble
Bass For weaker bass For stronger bass
Balance Decrease audio from 
the right speaker Decrease audio from 
the left speaker
 25
Item
 
						

							
Power Save Settings
ECO
Energy Save
No Signal Off
No Operation Off
Sleep Timer  [       Standard]
[Disable] 
[Disable]
Basic adjustment
No Signal Off
ECO
When set to “Enable”, the TV will automatically enter 
standby mode if there is no signal input for 15 minutes.
Five minutes before the TV enters standby mode, the 
remaining time displays every minute.
NOTEEven if a TV programme finishes, this function may not 
operate because of interference from other TV stations or 
other signals.
•
•
Energy Save
ECO
This function enables you to automatically reduce the 
backlight brightness in order to decrease the power 
consumption and increase the backlight life span.
The TV will automatically enter standby mode if no 
operations are performed during the time span you set 
(“30min.” or “3hr.”).
Five minutes before the TV enters standby mode, the 
remaining time displays every minute.
•
No Operation Off
ECO
Allows you to set a time when the TV automatically 
enters standby mode.
NOTE
Select “Off” to cancel the sleep timer.
When the time has been set, countdown automatically 
starts.
Five minutes before the preset of time expires, the 
remaining time displays each minute.
•
•
•
Sleep Timer
ECO
 26
Standard:
 Reduces the backlight brightness by 20%.
Advanced:  Reduces the backlight brightness by 30%.
Off:  The backlight brightness is the same value of your 
settings in the selected “AV MODE”.
Item
NOTE
This function does not work when “AV MODE” is set to 
“DYNAMIC (Fixed)”.
“Energy Save” status icons
Icon Description
“Energy Save” is set to “Standard”.
“Energy Save” is set to “Advanced”.
When “Energy Save” is set to “Standard” or 
“Advanced”, “Energy Save” status icons appear in the 
“Picture” menu and channel information windows as 
shown below.
EXAMPLE
Picture 
Contrast OPC [On]
Bri
ghtness [+30] [0] 0 
–30  +40 
+30 
Backlight [+14] –16 
+16 
DYNAMIC
When “OPC” is set to “On” or “On:Display”, an “Ener\
gy 
Save” status icon appears to the left of “OPC” in the 
“Picture” menu.
When “OPC” is set to “Off”, an “Energy Save” status icon 
appears to the left of “Backlight” in the “Picture” menu.
EXAMPLE
Subtitle Teletext Off
:
New Information 
PA L I
NICAM STEREO
AT V01
BBC1
•
E
•
•
 
						

							
Channel Settings
Auto Installation
Basic adjustment
Auto Installation
Setup
The TV automatically detects and stores all available 
services in your area. This function also allows you to 
perform the channel setting for digital and analogue 
individually and reconfigure the settings after the initial 
auto installation has been completed.After selecting “Yes” on the screen, you can set 
language and channel search the same as in the 
initial auto installation. Follow steps 2, 5 and 6 
on page 9.
NOTE
You cannot set the Home/Store setting and the country 
setting in “Auto Installation” in the “Setup” menu. If you 
want to reconfigure those settings, automatically execute 
initial auto installation after executing “Reset” from the 
“Setup” menu.
The current country setting is displayed on the screen.
•
•
Manual Adjust
Configure various settings for each service using the 
Colour (R, G, B)
 buttons.
DTV 993 Service 
No.  Old
LCN
CH
Skip
Lock 
Service 
Name 
SIT 3 
DTV 994  ✔ 
SIT 2 
DTV 995  ✔
SIT 1 
DTV 999 HD Monosco : Lock
R: CH SkipG: SortB
Press  a/b  to select the desired service.
Press the colour button on the remote control unit 
corresponding with the item you want to reconfigure.
The  ✔ mark indicates the operation is set to on. Each 
time the colour button is pressed, you can switch the 
corresponding operation on/off.
E
1
2
•
Programme Setup
Setup
Digital channel settings
Digital Setting
You can reconfigure the DTV service settings 
automatically or manually.
Additional Search
Use this menu to add new services automatically after 
auto installation has been completed.
Manual Search
Add new services within a specified frequency band.Enter the frequency using  0–9  numeric buttons.
You can perform “Manual Search” with a service number 
only when the five Nordic countries have been selected in 
the country setting.
E
E
•
•
 27
Buttons for Manual Adjust operation
Lock: Press R button.When the service is locked, you must enter your PIN 
whenever you tune to the service.
CH Skip: Press G button.Services with a  ✔ mark are passed over when pressing 
P r /s  on the TV or remote control unit.
Sort: Press B button.The item position of services can be sorted.
Press a/b  to select the service whose item 
position you want to move, and then press  OK.
DTV 994  ✔ 
SIT 2 
DTV 995  ✔
SIT 1 
Press  a/b  to move it to the desired position, 
and then press  OK.
DTV 994
✔
SIT 1
DTV 995 ✔
SIT 2
Repeat steps 1 and 2 until all desired service 
items are sorted.
1
2
3
 
						

							
Basic adjustment
Channels with “Skip” set to “On” are passed over 
when using Pr /s  even if selected while watching 
the image from the TV.
When connecting a decoder to the TV, you need to 
select “EXT1” or “EXT2”.
NOTE
The factory preset value is “Off”.
•
You can block the viewing of any channel.
NOTE
See “Child Lock” for setting a PIN.
When “Lock” is set to “On” for a channel, “Child lock has\
 
been activated” displays, and the image and sound of the 
channel are blocked.
When pressing  6 while “Child lock has been activated” 
displays, the PIN input window will display. Inputting the 
correct PIN unlocks the “Child Lock” temporarily until the 
power is turned off.
Sort
Channel positions can be sorted freely.
Press  c/d  to select “Yes”, and then press  OK.
Press  a/b /c /d  to select the channel you want 
to move, and then press  OK.
Press  a/b /c /d  to move it to the desired 
position, and then press  OK.
Repeat steps 2 and 3 until all desired channels 
are sorted.
Erase Programme
Channels can be erased individually. Press  c/d  to select “Yes”, and then press  OK.
Press  a/b /c /d  to select the channel you want 
to erase, and then press  OK.
A message window pops up.
Press  c/d  to select “Yes”, and then press 
OK  to erase the selected channel. All the 
subsequent channels move up.
Repeat steps 2 and 3 until all desired channels 
are erased.
•
•
•
E
1
2
3
4
E
1
2
•
3
4
Programme Setup
Setup
Analogue Setting
You can reconfigure the analogue TV channels settings 
automatically or manually.
Additional Search
Use this menu to add new channels automatically after 
auto installation has been made.
Start searching channels after selecting the colour system.
Manual Adjust
Use this menu to set up analogue TV channels 
manually.
After selecting “Yes” on the screen, press  a/b /
c /d  to select the channel you want to set and 
then press  OK.
E
•
E
You can adjust the frequency to the desired position.
NOTE
Adjust while checking the background picture as a 
reference.
Instead of pressing  c/d  to adjust the frequency, you 
can set by directly entering the frequency number of the 
channel with  0–9  numeric buttons.
EXAMPLE179.25 MHz: Press  1 s  7  s 9  s 2  s 5.
49.25 MHz: Press  4 s  9  s 2  s 5  s OK .
•
•
•
•
Select the optimum colour system to receive (“Auto”, 
“PAL”, “SECAM”).
Select the optimum sound systems (Broadcasting 
systems) to receive (“B/G”, “D/K”, “I”, “L/L’”).
When a TV channel sends its Network Name, the 
“Auto Installation” detects the information and assigns 
a name to it. However, you can change channel names 
individually.
Press  a/b /c /d  to select each character of the 
new name for the channel, and then press  OK.
Repeat step 1 above until the name is fully spelt 
out.
NOTE
The name can be five characters or less.
If a channel name is less than five characters, select “END” 
to set the channel name.
1
2
•
•
Analogue channel settings
 28
Fine
Colour sys.
Sound sys. (Broadcasting systems)
Label
Skip
Decoder
Lock