Sharp Lc 37ga3e Operation Manual

25
Language setting for on-screen
display
You can also select a language from setup menu.
Select from among 13 languages.
3
Press MENU and the MENU screen displays.1
2
4
Press c/d to select “Setup”.
Press a/b to select “Language”, and then
press OK.
Press a/b/c/d to select the desired
language listed on the screen, and then
press OK.
OPC setting
Automatically adjusts the brightness of the screen.
Press c/d to select “Picture”.
2
Using OPC on the menu screen
Press MENU and the MENU screen displays.
1...

30
Basic adjustment settings
No signal off
When set to “Enable”, the power will automatically shut
down if no signal inputs for 15 minutes.
Press a/b to select “No Signal Off”, and
then press OK.
Press c/d to select “Enable”, and then
press OK.
3
4
• Five minutes before the power shuts down,
remaining time displays every minute.
NOTE
• “Disable” is factory preset value.
• When a TV programme finishes, this function may not
operate.
Press c/d to select “Power Control”.2
Press MENU and the MENU screen...

25
Language setting for on-screen
display
Y
Select fr
3
PrMENU and the MENU scr1
2
4
Prc/d to select 

32
Using external equipment
Decoder
Connecting a decoder
You can use the INPUT 1 terminal when connecting a decoder and other audiovisual equipment.
NOTE
• In cases when the decoder needs to receive signal from the TV, make sure to set “Decoder” to “INPUT1” in the Programme
Setup “Manual Adjust” menu. (See page 23.)
VCR
SCART cable (commercially available)
Decoder
Connecting a VCR
You can use the INPUT 2 terminal when connecting a VCR and other audiovisual equipment.
If your VCR supports TV-VCR advanced...

33
Using external equipment
SCART cable
(commercially
available)
VCR
Using AV Link function
This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovisual
equipment.
NOTE
• Only works when the audiovisual equipment is connected to the INPUT 2 terminal on the TV with AV Link via a fully wired
SCART.
One Touch  Play
While the TV is in standby mode, it automatically turns
on and plays back the image from the audiovisual
source (e.g. VCR, DVD).
TV Standby
When...

34
Using external equipment
DVD player
Component cable
(commercially available)
When using component cable,
select “COMPONENT” for “Input
Select” in the menu.
Connecting a DVD player
You can use the INPUT 3 terminal when connecting to a DVD player and other audiovisual equipment.
Game console/Camcorder
Composite video cable
(commercially available)S-video cable
(commercially available)
Connecting a game console or camcorder
A game console, camcorder and some other audiovisual equipment are conveniently...

27
Basic adjustment settings
C.M.S. (Colour Management System)
Colour tone is managed using the six-colour
adjustment setting.
PrMENU and the MENU scr
1
2Prc/d to select 

36
Rear view
Using external equipment
Connecting external speakers
Make sure to connect the speaker terminal and
cable polarity (L, +) properly.
• The speaker terminals have plus (L) and minus (+)
polarity.
• Plus is red and minus is black.
• The cables are also divided into plus and minus.
• When connecting the left/right speakers, be sure to
connect the plus/minus terminals with the correct cables.
NOTE
• Unplug the AC cord from the AC outlet before installing
the speakers.
CAUTION
• Make sure external...

25
Language setting for on-screen
display
Y
Select fr
3
PrMENU and the MENU scr1
2
4
Prc/d to select 

38
Useful adjustment settings
Fine Sync. adjustment (PC input
mode only)
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimise the image.
1
2
Press MENU and the MENU screen displays.
Press c/d to select “Setup”.
4
3Press a/b to select “Fine Sync.”, and then
press OK.
Reset
H-Pos. [90]–+
V-Pos.
Clock
Phase[39]
[90]
[20]–
–
–+
+
+
5Press c/d to adjust the item to your
desired position.
NOTE
• For...