Sharp Lc 37ga3e Operation Manual

9
Preparation
Simple operations for watching a TV programme
Basic connection
Connecting to an antenna
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of connecting to an
antenna with a coaxial cable.
Antenna cables–commercially available
If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325
plug (IEC 169-2), plug it into the IN terminal at the rear of the TV.
LC-37GA3E(E)-b04.6.25, 7:52 AM 9
 

10
01 SAT.1 02 PR07 03 KABEL
01 SAT.1 02 PR0703 KABEL
01 55.25 02 85.25 03 102.25
Initial auto installation
When the TV powers on for the first time after purchase
(see page 14), the initial auto installation is invoked.
You can automatically set language, country and
channels in successive operations.
Preparation
Setting the country or area
1Press a/b/c/d to select your country
or area listed on the screen.
2Press OK to enter the setting.
• The programme auto search starts at the same
time.
Setting the...

11
Part names
POWER button (a)
TV
INPUT button VOLUME buttons ( il/k )
CHANNEL buttons
(Ps/r)
*OPC: Optical Picture Control
(See page 25.) POWER indicator OPC sensor Remote control sensor
SLEEP timer indicatorOPC indicatorHeadphone jack
Remote control sensor indicator
LC-37GA3E(E)-b04.6.25, 7:53 AM 11

NOTE

12
Part names
RESET*INPUT 3 terminals
SYSTEM RESET**
TV
Antenna input terminal
*Press RESET if the TV cannot return to its original state after performing various operations.
• AV MODE resets to USER.
• Analogue TV channel resets to channel 1.
• Dual picture resets to normal.
• Audio setting initializes.
• Dolby Virtual resets to Off.
• Image position initializes.
**Press SYSTEM RESET if the TV does not operate after starting up.
NOTE
• Pressing RESET will not work if the TV is in standby mode (indicator...

13
Part names
12
8
10
11
9
34
5
1320 16
17
18
19
21
22
23
14
12
24
25
1527
28
26
6
7
NOTE
• When using the remote control unit, point it at the Display.
Remote control unit1B (STANDBY/ON)
To switch the power on and off. (See page 14.)
2 OPC
To switch the Optical Picture Control on and off. (See page
25.)
3c (DUAL screen)
Set the dual picture mode. Press c again to return to normal
view. (See page 48.)
SELECT
To select either screen to be active in Dual screen mode.
4d (FREEZE/HOLD)
TV/External input...

14
 POWER
Turning on the power
Off
Red
Green
Display status indicator
Power off
The TV is in standby mode.
The TV is on.
  POWER indicatorPress POWER on the TV.
• POWER indicator (Green): The TV is on. (After a few seconds, a window
appears with sound.)
NOTE
• The initial setup starts when the TV powers on for the first time. If the TV
has been turned on before, the initial auto installation will not be invoked.
See page 20 to try Auto installation from the Setup menu.
Turning off the power
Press B on...

15
Watching TV
Simple button operations for
changing channels
You can change channels in several ways.
Using Pr/son the remote control unit
• Press Pr to increase channel number.
• Press Ps
      
 to decrease channel number.
NOTE
•Ps/r on the Display operates the same as Ps/ron
the remote control unit.
Channel display
MONO12 SAT.1
12 SAT.1
B/G PAL
(Example)
Ps/r
Using 0 – 9 on the remote control unit
Select the channels directly by pressing buttons 0 to
9.
a
To select a 1-digit channel (e.g. channel...

16
Watching TV
Using SOUND on the remote control unit
In the NICAM TV broadcasts
When receiving a stereo signal
Each time you press SOUND, the mode switches
between NICAM STEREO and MONO.
In the TV mode of A2 TV broadcasts
When receiving a stereo signal
Each time you press SOUND, the mode switches
between STEREO and MONO. When receiving a bilingual signal
Each time you press SOUND, the mode switches
among NICAM CH A, NICAM CH B, NICAM CH AB
and MONO.
When receiving a monaural signal
Each time you press...

11
P
POWER button \(
\)
TV
INPUT button VOLUME buttons \( l/k \)
CHANNEL buttons
\(P/\)
*OPC: Optical Pictur
\(See page 25.\) POWER indicator OPC sensor Remote contr
SLEEP timer indicatorOPC indicatorHeadphone jack
Remote contr
LC-37GA3E(E)-b04.6.25, 7:53 AM 11

NOTE
• Within 30 minutes of pressing e, mute can be cancelled
by using the methods below.
• Pressing i
f ff f
f/i
e ee e
e or e can also cancel the mute.•Mute will be cancelled after 30 minutes have elapsed.
However, the TV will not suddenly...

14
 POWER
Turning on the power
Off
Red
Green
Display status indicator
Power off
The TV is in standby mode.
The TV is on.
  POWER indicatorPress POWER on the TV.
• POWER indicator (Green): The TV is on. (After a few seconds, a window
appears with sound.)
NOTE
• The initial setup starts when the TV powers on for the first time. If the TV
has been turned on before, the initial auto installation will not be invoked.
See page 20 to try Auto installation from the Setup menu.
Turning off the power
Press 
 on...