Sharp AR M620U User Manual

SPECIAL MODES
5-25
5
Book copy
This function is convenient when you wish to compile copies of books or other bound originals into an attractive
pamphlet format. The two pages of the open book are scanned as a set, and two pages each are copied onto the
front and back sides of the copy paper (four pages are copied onto one sheet of copy paper). This allows the copies
to be folded down the centre and made into a pamphlet.
[Example] Book copying an 8-page pamphlet

Scan the originals from the first page to...

SPECIAL MODES
5-26
Tab copy
Copying is possible on the tabs of tabbed paper. Prepare appropriate originals for the tab captions.
[Example]
Relations between originals and tabbed paper
Original Tabbed paper Copy
Tab width
A4 : Maximum of 20 mm
(8-1/2 x 11 : Maximum of 5/8)
INDEXINDEX
Area A
Area B

The tab caption is shifted by the amount of the tab width setting, so keep areas A and B blank.
Left binding
(normal top-bottom)Right binding 
(Inverted top-bottom)Right binding 
(Inverted top-bottom)...

SPECIAL MODES
5-27
5
1Touch the [TAB COPY] key in the special
modes screen (2nd screen).
The TAB COPY setting
screen will appear. A
tab copy icon ( ) will
also appear in the
upper left corner of the
screen to indicate that
the function is turned
on.
2Set the tab width if necessary and touch
the [OK] key.
Set the tab width with the
 and   keys. The
width can be set from 0
to 20 mm (0 to 5/8) in
increments of 1 mm (1/
8).
3Touch the [OK] key in the special modes
screen.
You will return to the main screen...

SPECIAL MODES
5-28
Card shot
When copying a card, this function allows you to combine the front and back sides on a single sheet of paper.

Copying is only possible on standard size paper.

A copy ratio cannot be selected when using this
function.

The image cannot be rotated when using this
function.
1Touch the [PAPER SELECT] key and then
select the desired paper size.
The selected paper size
key is highlighted and
the paper selection
screen closes.
2Touch the [CARD SHOT] key in the special
modes screen...

SPECIAL MODES
5-29
5
4Touch the outer [OK] key.
You will return to the
main screen of copy
mode.
5Place the original on the document glass.
Place the front side of
the original face down
and close the
document cover.
6Follow steps 4 through 6 of Copying from
the document glass (page 4-12).
7Press the [START] key.
The front side of the
card is scanned.
8Place the back side of the original face
down on the document glass (see step 5).
9Press the [START] key.
The back side of the
card is scanned.
10Touch...

SPECIAL MODES
5-30
Mirror image
This function is used to print a mirror image of the original. The images will be inverted in the right to left direction on
the copies.
1Touch the [MIRROR IMAGE] key in the
special modes screen (3rd screen).
The [MIRROR IMAGE]
key will be highlighted to
indicate that the function
is turned on, and the
mirror image icon ( )
will appear in the upper
left of the screen.
2Touch the [OK] key on the special modes
screen.
You will return to the main screen of copy mode.
B/W...

5-31
5 STORING, USING AND DELETING
JOB PROGRAMS
The steps of up to 10 copy jobs can be stored as job programs. Job programs can be called up with ease, and are
retained even when the power is turned off. By storing frequently used copy settings in  a job program, you can
eliminate the bother of selecting the settings each time you use them for a copy job.

If any settings related to the steps of a job program are changed in the key operator programs after the job program
is stored, the steps related to...

STORING, USING AND DELETING JOB PROGRAMS
5-32
Calling up a job program
1Press the [#/P] key.
2Touch the number key of the desired job
program.
The screen
automatically closes and
the job program is called
up. A number key that
does not have a job
program cannot be
selected.
3Set the number of copies if needed and
then press the [START] key.
Copying will begin using
the settings of the job
program.
Deleting a stored job program
1Press the [#/P] key.
2Touch the [STORE/DELETE] key.
3Select a storage...

5-33
5 INTERRUPTING A COPY RUN
The copy of the original scanned in interrupt mode is output before the remainder of the interrupted copy job.
1Touch the [INTERRUPT] key.
If interrupt copying is
possible during a copy
run, the [INTERRUPT]
key will appear. (If the
key does not appear,
interrupt copying is not
possible.)
When the [INTERRUPT]
key is touched in step 1,
the [INTERRUPT] key
will be replaced by the
[CANCEL] key as shown
in the illustration. 
To cancel an interrupt
copy job while the interrupt...

Downloaded From ManualsPrinter.com Manuals