Schwinn S 25 Manual

130 /1.0
170 /1.5
ASSEMBLY MANUAL / OWNER’S MANUAL  
Manual en Espa\361ol Latino Americano:
http://www  

2
Important Safety Instructions - Assembly 3
  Safety Warning Labels / Serial Number  4
Specifications 5
Before Assembly  5
Parts 6
Hardware 7
Tools 7
Assembly 8
Leveling the Bike  14
Moving the Bike  14Important Safety Instructions - Owner’s 
15
Features 16
  Console Features  17
  Remote Heart Rate Monitor  20
Operations 22
 Adjustments  22
  Initial Setup  22
  Quick Start / Manual Program  23
  User Profiles  23
  Profile Programs  25
  Pausing or Stopping  28
 Results  28
  GOAL TRACK Statistics...

3
ImporTanT safeTy InsTruCTIons 
— assembly
!This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
!Read and understand all warnings on this machine.
Carefully read and understand the Assembly instructions.
•	 Keep	bystanders	and	children	away	from	the	product	you	are	assembling	at	all	times.
•	 Do	not	connect	power	supply	to	the	machine	until	instructed	to	do	so.
•	 Do	not	assemble	this	machine	outdoors	or	in	a	wet...

4
safeTy WarnIng labels and serIal number
FCC Compliance
!Changes	or	modifications	to	this	unit	not	expressly	approved	by	the	party	responsible	for	compliance	could	void	
the user’s authority to operate the equipment.
The machine and power supply comply with part 15 of the FCC rules. Opera\
tion is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired...

5
speCIfICaTIons
41.3” (105cm)
21.4” (54cm)55.6” (141cm)
Before Assembly 
Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a 
hard,	level	surface.	Allow	a	workout	area	of	a	minimum	90”	x	70”	(2.3m	x	1.8m).
Basic Assembly Tips
Follow these basic points when you assemble your machine:
1.   
Read and understand the “Important Safety Instructions” before assembly.
2.    Collect all the pieces necessary for each assembly step.
3.    Using the...

6
parTs
ItemQtyDescription ItemQtyDescription
1 1Main Frame 91Seat Post
2 1Front Stabilizer 101Adjustment Knob
3 1Rear  Stabilizer 111Seat
4 1Top Shroud 121Left Pedal (L)
5 1Mast Gasket 131Right Pedal (R)
6 1Console Mast (with Handlebar Mount)  141Water Bottle Holder
7 1Handlebars 151AC Adapter
8 1Console 161Handlebar Mount Cover
  Note:   Media Cable is in a bag.
12 (L) 13 (R)11
7
1
2 4
8
5
14
3
9
15
10
616  

7
HardWare / Tools
To o l s
Included         Not Included
6 mm (recommended)
Item
QtyDescription
A 4Button	Head	Hex	Screw	M8	x	25
B 5Lock Washer M8
C 4Curved Washer M8
D 1Flat Washer M8
E 1T-handle
D E  

8
assembly
1.  Attach Stabilizers to Main Frame
 
Note:   Hardware (*) is pre-installed on the stabilizers and not on Hardware Card. Make sure transport wheels on the 
front stabilizer point forward, and the Schwinn® decal on the rear stabilizer faces outward from the machine.
2.  Install Console Mast, Mast Gasket and Top Shroud on Main Assembly
 N OTI C E :    Make sure the Console Cable connector (a) does not fall into the Console Mast. Align the clips on the cable 
connectors	and	make	sure	the...

9
3. 
Install Handlebars on Console Mast
  N OTI C E : 			Do	not	crimp	the	cables.	Put	the	Handlebar	(7)	in	the	bracket	(6a),	adjust	the	Handlebar	to	the	desired	angle, 	
and install the T-handle (E) through the holes. Use the pull cable in the Handlebar Mount to route the HR 
cable (7a) through the slot (6c) under the Handlebar Mount to the top of the mast. Fully tighten the T-handle 
to keep the Handlebar in position. Push the cover (16) into position on the Handlebar Mount.
7
6a
16
E
6a
E
D
B
7
6a
D...

10 4. Install Console on Console Mast 
 Note:    Remove the pre-installed screws (*) from the back of the Console before you connect the cables.
 N OTI C E :    Do	not	crimp	the	cables. 	
8
X4
#2
*
X4
#2
8
*