Sanyo Projector Plc Wxu300 User Manual

							
51

Setting
Picture in PictureThis function is used to project two videos simultaneously
by placing a separate small sub screen within the main
screen. (Picture in Picture combinations provided in this 
projector are shown on pages 75.)
Only the sound on the main picture is heard, the sound
on the sub picture cannot be heard.( In P in P, the big 
picture is main picture, and the small one is sub picture; in P 
by P, the left picture is main picture, and the right one is sub 
picture.)
  Mode. . . . . P in P :  The sub picture in the main picture.
                     P by P:  The sub picture by the main picture.
                     Off     :   Exit the Picture in Picture menu.
  Subpicture size. . .  Select the subpicture display size. 
                                    Subpicture can be changed  
                                    between Large, Small and Middle. 
  Subpicture position. .  Set a position for subpicture. This 
                                         function is used to set Subpicture 
                                         position as follows:
                                         the top left→ the bottom left →
                                         the bottom right→ the top right→ • • •
Selecting the Main picture or Sub picture
During Picture in Picture mode, and no operation on the On 
Screen Menu, press the SELECT button to select main or 
sub picture. (When the sub picture is selected,  a red frame 
will be displayed.)
Switching of the Input Source
In the main picture or the sub picture mode, choose input 
soure by pressing the INPUT button on the top control or 
pressing the COMPUTER 1/2, HDMI, VIDEO, S-VIDEO or 
COMPONENT button on the remote control or through Input 
Menu operation.
Operation of the Sub picture
In Picture in Picture mode, press the SELECT button to 
select the sub picture (the frame becomes red), and then 
use the Point ▲▼◄► buttons to change Subpicture size, 
switch the Main picture and the Sub picture, and move 
Subpicture position.
   • In Picture in Picture mode, press the Point ▲ button to   
     switch the Main picture and the Sub picture. 
   • In P in P,  press the Point ▼ button to change Subpicture   
     size.
   • In P in P,  press the Point ◄► buttons to move 
     Subpicture position.
Picture in Picturemore...Standby mode                                          Network
Picture in Picture
Note:
• When the input signal(s) is/are incompatible, X mark will
  be displayed on the Main/Sub picture.
• When the sub picture is set to the same signal as the main
  picture, X mark will be displayed.
  • Subpicture position and Subpicture size are only used  
    for P in P.
Subpicture size
Note:
• When P in P or P by P is set, Total dots is 
  disabled in the PC adjust menu. 
• In Picture in Picture mode, the Freeze function 
  is disabled.
• During Picture in Picture mode and the Menu 
  screen is displayed, below functions via the 
  remote control operation are disabled.
   • Change Subpicture size.
   • Move Subpicture position.
   • Switching of the Main picture and Sub picture.
   • Select the Sub picture mode by the SELECT   
     button. 
						

							
5

Setting
Power management
Timer	left	before	Lamp	is	off.
Power management
For	reducing	power	consumption	as	well	as	maintaining	
the	lamp	life,	the	Power	management	function	turns	off	the	
projection	lamp	when	the	projector	is	not	operated	for	a	
certain	period.
Select	one	of	the	following	options:
Ready	.................. 	When	the	lamp	has	been	fully	cooled	
down,	the	POWER	indicator	changes	
to	green	blinking.	In	this	condition,	the	
projection	lamp	will	be	turned	on	if	the	
input	signal	is	reconnected	or	any	button	
on	the	top	control	or	remote	control	is	
pressed.	
Shut down 	.......... 	When	the	lamp	has	been	fully	cooled	
down,	the	power	will	be	turned	off.	
Off 	....................... 	Power	management	function	is	off.	
Timer	................... 	If	the	input	signal	is	interrupted	and	
no	button	is	pressed	for	more	than	
30	seconds,	the	timer	display	with	
No 
signal 	appears.	It	starts	the	countdown	
until	the	lamp	is	turned	off.	Use	the	Point	
▲▼	buttons	to	set	the	 Timer(1~30min).
Note:
		Factory	default	is	
Ready: 5 min.
Standby mode
This	function	is	available	when	operating	the	projector	via	
network.
	Network 	.... 	Supply	 the	power	 to	the	 network	 function	 even	
after	turning	off	the	projector.	 You	can	turn	on/
off	the	projector	via	network,	modify	network	
environment,	and	receive	an	e-mail	about	
projector	status	while	the	projector	is	powered	
off.
	Eco 	............ 	Select	Eco	when	you	do	not	use	the	projector	
via	network.	 The	projector’s	network	function	
will	stop	when	turning	off	the	projector.
Refer	to	the	owner’s	manual	of	“Network	Set-up	and	
Operation”.
Note:
•	Factory	default	is	
Eco.
•	When	selecting	
Network ,	the	cooling	fans	may	be	running	
		depending	on	the	temperature	inside	the	projector	even	if	
		the	projector	is	turned	off. 
						

							
53

Setting
On start
When	this	function	is	set	to On,	the	projector	will	be	
automatically	turned	on	just	by	connecting	the	 AC	power	
cord	to	a	wall	outlet.	
Note:
•	 Be	sure	to	turn	off	the	projector	properly	(see	"Turning	Off	
the	Projector"	on	page	20).	If	the	projector	is	turned	off	
in	the	incorrect	sequence,	the	On	start	function	does	not	
work	properly.
•	 On	start	function	is	available	only	when
 Network 	is	
selected	in	Standby	mode	function.	(p.52)
On start 
						

							
54

Press	the	Point	▲▼	buttons	to	
select	
Off ,	CC1 ,	CC ,	CC3	or	CC4,	
and	then	Press	Select	button.
Setting
Closed caption
Closed	caption	is	a	printed	version	of	the	program	sound	or	
other	information	displayed	on	the	screen.	If	the	input	signal	
contains	closed	captions,	you	can	turn	on	the	feature	and	
switch	the	channels.	Press	 the	Point	▲▼	buttons	to	select	
Off,	CC1 ,	CC ,	CC3	or	CC4.		
If	the	closed	caption	is	not	clear,	you	can	change	the	text	
from	
Color 	to	White.
Closed Caption
Note:
The	Closed	Caption	is	available	only	under	the	situation	
below.
    •	When	the	input	signal	is	NTSC 	of	composite	and									
						S-video,	and	the	system	is	set	according	to	the	signal		
						or	set	on	
Auto .		
	 	 •	 The	system	must	be	set	on	
NTSC 	or	Auto	in	Video				
		System	Selection.	(p.39)	
	 	 •	 The	icon	of	Closed	caption	is	displayed	in	gray	while	it 	
							is	not	available.	
	 	 •	 The	Closed	caption	is	unavailable	when	On-Screen
						menu	and	P-Timer	are	displayed,	and	Picture	in	
							Picture	is	active.
Power management                                      Off                  On start                                                         Off 
						

							
55

Remote control
This	function	allows	you	to	change	brightness	of	the	
screen.
Normal	...... 	Normal	brightness	
Eco 	............ 	Lower	brightness	reduces	the	lamp	
power	consumption	and	extends	the	
lamp	life.
Lamp control 
Remote control
Lamp life control
This	projector	provides	two	different	remote	control	codes:	
the	factory-set	initial	code	(Code	1)	and	the	secondary	code	
(Code	2).	 This	switching	function	prevents	remote	control	
interference	when	operating	several	projectors	or	video	
equipment	at	the	same	time.
When	operating	the	projector	in	 Code ,	both	the	projector	
and	the	remote	control	must	be	switched	to	 Code 
.
To change the code for the projector:
Select	either	
Code 1	or	Code  	in	this	Setting	Menu.
To change the code for the remote control:
Press	and	hold	both	the	MENU	and	IMAGE	buttons	
together	for	5	seconds	or	more.		 After	changing	the	code,	
make	sure	the		remote	control	operates	properly.
Lamp control
Select	the	lamp	operation	when	the	total	lighting	time	of	a	
lamp	exceeds	the	recommended	total	hours	of	use.
Mode 1 	.............. 	A	lamp	can	be	turned	on	even	after	
exceeding	the	recommended	total	
hours	of	use.
Mode  	.............. 	A	lamp	can	be	turned	on	even	after	
exceeding	the	recommended	total	
hours	of	use.	But	the	projector	turns	off	
automatically	after	3	minutes.
Lamp life control
Note:
•	When	different	codes	are	set	on	the	projector	and	on	the	remote	control,	any	operation	cannot	be	made.	In	
			that	case,	switch	the	code	on	the	remote	control	to	fit	the	code	on	the	projector.
•	If	the	batteries	are	removed	from	the	remote	control	for	a	long	period	of	time,	the	remote	control	code	will	be	
		reset.
Power management                                      Off                  On start                                                         Off
	Note:
•	 Lamp	mode	cannot	be	changed	for	a	while	after	turning	
		on	the	projector.	Lamp	needs	some	time	to	stabilize	
		after	the	power	is	turned	on.	Stored	lamp	mode	will	be	
		active	after	the	lamp	is	stabilized.
•	If	 Mode  	has	been	selected	and	the	projection	lamp	
		exceeds	the	recommended	total	hours	of	use,	the	
		replacement	icon	will	be	displayed	at	the	time	of	power-
		on.	 Then	the	projector	will	turn	off	after	3	minutes.
	 •	 The	Lamp	replacement	icon	will	not	appear	when	the	
				Display	function	is	set	to	
Off 	(p.46),	during	"FREEZE	
button"	(p.25),	or
  "NO	SHOW	button"	(p.26).
Lamp replacement icon
Setting 
						

							
56

Key lock
Key lockSecurity (Key lock and PIN code lock)
PIN code lock
This	function 	locks 	the 	top 	control 	and 	remote 	control	
buttons	to	prevent	operation	by	unauthorized	persons.
Select	
Key lock 	and	 then	 press	 the	SELECT 	button,	 and	
select	the	desired	item	by	pressing	the	Point	
▲▼	buttons.
	 .....	Unlocked.
	 ..... 	Lock	the	operation	of	the	top	control.	 To	
unlock,	use	the	remote	control.
	 ..... 	Lock	the	operation	of	the	remote	control.				
To	unlock,	use	the	top	control.
If	 the	 top	control	 accidentally	 becomes	locked	and	you	do	
not	 have	 the	remote	 control	nearby	 or	there	 is	something	
wrong	 with	your	 remote	 control,	 contact	the	dealer	 where	
you	purchased	the	projector	or	the	service	center.
This	 function	 allows	you	to	use	 the	Key	 lock	 and	PIN	code	
lock	function	to	set	the	security	for	the	projector	operation.
This	function	prevents	the	projector	from	being	operated	
by	unauthorized	persons	and	provides	the	following	
setting	options	for	security.
	 Off 	............	Unlocked.
	 On1 	.......... 	Enter	the 	PIN 	code 	every 	time 	turning 	on	
the	projector.
	 On2 	.......... 	Enter	 the	PIN	 code	 to	operate	 the	projector	
once 	the 	power 	cord 	is 	disconnected; 	as	
long 	as 	the 	AC 	power 	cord 	is 	connected,	
the 	projector 	can 	be 	operated 	without 	a	
PIN	code.
Whenever	 you	change	 the	PIN	 code	 lock	setting	 or	the	
PIN 	code 	(the 	four-digit 	number), 	you 	are 	required 	to	
enter	 the	PIN	 code.	 The	“1234”	 is	set	 as	the	 initial	 PIN	
code	at	the	factory.	
If	 you	 want	 to	change	 the	PIN	 code	 lock	setting,	 Press	
t h e 	S E L E C T 	b u t t o n 	a n d 	t h e 	P I N 	c o d e 	d i a l o g 	b o x	
appears.
PIN code lock
Setting
When 	the 	projector 	is 	locked 	with 	the 	PIN 	code, 	the	
Security	icon	appears	on	the	guide.
Power management                                      Off                  On start                                                         Off 
						

							
57

Use	the	Point	▲▼	buttons	to	select	Off,	On1 	or	On ,	and	
then	press	the	SELECT 	button	to	make	a	choice.
Change the PIN code lock setting
Enter a PIN code
Use	the	Point	▲▼	buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer	 to	the	 next	 box.	The	number	 changes	 to	“
”.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	 entering	 the	four-digit	 number,	move	the	pointer	 to	
“Set.”	 Press	 the	SELECT 	button	 so	that	 you	can	start	 to	
operate	the	projector.
If	 you	 entered	 an	incorrect	 PIN	code,	
PIN  code 	and	 the	
number	 (
)	will	 turn	 red	for	a	moment.	 Enter	the	
correct	PIN	code	all	over	again.
Enter a PIN code
The	PIN	code	can	be	changed	to	your	desired	four-digit	
number.	Press	the	SELECT 	button	to	select	
PIN code 
change.	PIN code 	dialog	box	appears,	use	the	Point	
▲▼	buttons	to	enter	the	correct	code.	 The	New	PIN	code	
input	dialog	box	appears.	Set	a	new	PIN	code.
Change the PIN code
CAUTION:
WHEN yOU  HAVE CHANGED  THE PIN  CODE, WRITE 
DOWN  THE  NEW  PIN  CODE  IN  COLUMN  OF  THE 
PIN  CODE  NO .  MEMO  ON  PAGE   80, AND KEEP  IT 
SECUREL y .  IF  yOU  FORGET  yOUR  PIN  CODE, THE 
PROjECTOR CAN NO LONGER BE STARTED .
Setting
PIN code change 
						

							
58

This	function	 provides	 the	following	 options	in	the	 cooling	
fans’ 	operation	when	the	projector	is	turned	off	(p.20).
	L1	...... 	Normal	operation
	L 	...... 	S l o w e r 	a n d 	l o w e r - s o u n d 	t h a n 	t h e 	n o r m a l	
operation	 (
L1),	but	 it	takes	 more	time	to	cool	 the	
projector	down.
Fan
This	projector	provides	Fan	control	function	in	the	Setting	
menu.
Choose	the	running	speed	of	cooling	fans	from	the	following	
options	according	to	the	ground	elevation	under	which	you	
use	the	projector.	
Off ................	Normal	speed.	Set	this	function	to	Off	when	
																						using	the	projector	in	non-high	altitude	
																						environment.	
On 1 .............	Faster	than	Off	mode.	Select	this	mode	
																						when	using	the	projector	in	high	altitudes	
																						(about	1,200	meters	or	more	above	the	sea	
																						level)	where	the	fans	have	less	cooling	
																						effect.	
On  .............	Faster	than	On	1	mode.	Select	this	mode	
																						when	using	the	projector	in	higher	altitudes	
																						than	above	where	the	fans	have	lesser	
																						cooling	effect.
Note:
	 The	fan	noise	becomes	louder	in	On 1 and  On .	
Fan control
Setting
This	function	is	used	to	set	a	frequency	for	the	filter	
cleaning.
When 	the 	projector 	reached 	a 	specified 	time 	between	
cleanings, 	a 	Filter 	warning 	icon 	appears 	on 	the 	screen,	
notifying	 the	cleaning	 is	necessary.	 After	cleaning	 the	filter,	
be 	sure 	to 	select 	
RESET 	and 	set 	the 	timer. 	The 	Filter	
warning	icon	will	not	turn	off	until	the	filter	counter	is	reset.
For	 details	 about	resetting	 the	timer,	 refer	to	“Resetting	 the	
Filter	Counter”	on	page	62.
Filter counter 
Filter counter
Press	the	SELECT 	button	to	select		Timer,	and	
then	use	the	Point	
◄►	buttons	to	set	the	timer.	
Select	from	(
Off/100H /	00H /	300H)	depending	
on	the	use	environment.
Filter	warning	icon	appears	on	the	screen	at	a	set	time. Fig .1 			Filter	warning	icon
Note:
	 This	icon	also	appears	at	turning	on.
Note:
				 The	Lamp	replacement	icon	will	not	appear	when	the	
				Display	function	is	set	to	
Off 	(p.46),	during	"FREEZE	
button"	(p.25),	or
  "NO	SHOW	button"	(p.26). 
						

							
5

Factory default
This	function	returns	all	setting	values	except	for	the	User 
logo,	PIN code lock ,	Logo PIN code lock ,	Lamp counter	
and	
Filter counter 	to	the	factory	default	settings.
Factory default
WARNING log
This	function 	records 	anomalous 	operations 	while 	the	
projector	 is	in	 operation	 and	use	it	when	 diagnosing	 faults.	
Up	 to	10	 warning	 logs	are	displayed	 with	the	latest	 warning	
message	 at	the	 top	of	the	 list,	 followed	 by	previous	 warning	
messages	in	chronological	order.	
Note:
	 		When 	the 	Factory 	default 	function 	is 	executed, 	all 	the	
warning	log	records	will	be	deleted.
Setting
Power management                                      Off                  On start                                                         Off
---- 
						

							
60

Input Source Information Display
The Information Menu is used for checking the status of the image signal\
 being projected and the operation of the projector.
H-sync freq.
V-sync freq.
Lamp counter
Information Menu
The horizontal frequency of the input signal is displayed in 
KHz, or - - - - - when no signal.
The vertical frequency of the input signal is displayed in Hz, 
or - - - - -  when no signal. Numbers of Hz doubles when 
during Interlace.
The cumulative lamp operating time is displayed.
Direct Operation
Press the INFO. button on the remote control to display the 
Information Menu.
INFO. button
Remote Control
Press the Point ▲▼ buttons to select the Information. The 
Information Menu is displayed. 
See below for displayed information.
Menu Operation
Power management
Screen
Off, Ready, Shut down or Timer is displayed.
The selected screen size is displayed.
Input
Lamp status
The selected input source is displayed.
The selected lamp mode is displayed.
Information
Language
The selected language is displayed.
Key lock
The selected Key lock icon is displayed.
PIN code lock
Off or On 1 or On 2 is displayed.
Remote control
The selected remote code  is displayed.