Sanyo Projector Plc Wxu10n User Manual
Have a look at the manual Sanyo Projector Plc Wxu10n User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 32
EN-31
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt or
spots will project on the screen and diminish image quality. If any othe\
r parts need
replacing, contact your dealer or qualified service personnel. When clea\
ning any part of
the projector, always switch off and unplug the projector first.
Warning:
Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service...](http://img.usermanuals.tech/thumb/67/95740/w64_sanyo-plc-wxu10-manual_d-31.png "Page 32
EN-31
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt or
spots will project on the screen and diminish image quality. If any othe\
r parts need
replacing, contact your dealer or qualified service personnel. When clea\
ning any part of
the projector, always switch off and unplug the projector first.
Warning:
Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service...")
![Page 34
EN-33
Replacing the Lamp
Projector lamps have a finite life. Replace the lamp when:JA warning message “Lamp is approaching the end of its useful life in full power
operation. Replacement suggested!” appears on the screen.
JThe image becomes darker and hues become weaker after a lamp has been for a long
period of time.
JRefer to section titled “LED Indicator Messages” for further details.
JThe lamp becomes high temperature after turning off the projector with t\
he ON/
STAND-BY button. If you touch the...](http://img.usermanuals.tech/thumb/67/95740/w64_sanyo-plc-wxu10-manual_d-33.png "Page 34
EN-33
Replacing the Lamp
Projector lamps have a finite life. Replace the lamp when:JA warning message “Lamp is approaching the end of its useful life in full power
operation. Replacement suggested!” appears on the screen.
JThe image becomes darker and hues become weaker after a lamp has been for a long
period of time.
JRefer to section titled “LED Indicator Messages” for further details.
JThe lamp becomes high temperature after turning off the projector with t\
he ON/
STAND-BY button. If you touch the...")
![Page 41
EN-40
Serial Control Interface
This projector provides a function to control the projectors operations\
by using the RS-232C
serial port.
„
Connection and Operation
Connect a RS-232C serial cross cable to RS-232C
PORT on the projector and serial port on the PC.
Launch a communication software provided with PC
and setup the communication condition as follows:
Send the command strings by the HEX key (HEX is in
the range of 0-9 and a-f) for controlling the projector.1
2
3Baud rate : 19200 bps
Parity...](http://img.usermanuals.tech/thumb/67/95740/w64_sanyo-plc-wxu10-manual_d-40.png "Page 41
EN-40
Serial Control Interface
This projector provides a function to control the projectors operations\
by using the RS-232C
serial port.
„
Connection and Operation
Connect a RS-232C serial cross cable to RS-232C
PORT on the projector and serial port on the PC.
Launch a communication software provided with PC
and setup the communication condition as follows:
Send the command strings by the HEX key (HEX is in
the range of 0-9 and a-f) for controlling the projector.1
2
3Baud rate : 19200 bps
Parity...")
EN-40 Serial Control Interface This projector provides a function to control the projectors operations\ by using the RS-232C serial port. „ Connection and Operation Connect a RS-232C serial cross cable to RS-232C PORT on the projector and serial port on the PC. Launch a communication software provided with PC and setup the communication condition as follows: Send the command strings by the HEX key (HEX is in the range of 0-9 and a-f) for controlling the projector.1 2 3Baud rate : 19200 bps Parity check : none Stop bit : 1 Flow control : none Data bit : 8 „Command FormatThe command is sent from PC to the projector with the format as below table. The projector decodes the command and returns the confirmation ACK = \ 06. The below table shows the typical command lists for controlling the projector. Please consult your local dealer for further information of another commands. Command Power ON Power OFF Menu S UP T W Left X Right Input Auto PC Adj. Mute Keystone UP Keystone DOWN Volume UP Volume DOWN NO Show Freeze Aspect Select Computer (Analog) Select Component Select S-Video Select Video Select Computer (Digital) BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BEEF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF 10 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 05 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 0600 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00C6 57 C8 FB 2A 9D 4C 7F 58 51 E0 D3 62 D5 CE 02 31 0B DA 6D BC 8F FF D0 D7 D7 D6 D7 D6 D6 D5 D7 D1 D1 D7 D6 D0 D0 D0 D2 D3 D2 D3 D3 11 2E 01 02 03 04 05 06 11 08 29 2A 0B 0C 27 2B 28 32 33 34 35 36 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Command Strings (HEX)
EN-41 Printed in China Part No. 1AA6P1P5446-- (KJ3A)SANYO Electric Co., Ltd.