Sanyo Plc Xf46n Projector User Manual

							41
SETTING
On start
When this function is “On,” projector is automatically turned on just
by switching MAIN ON/OFF SWITCH on.
Note ;Be sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P23).  If projector is turned
off in wrong steps, On Start function does not operate
properly.
This projector provides eight different remote control codes (Code
1-Code 8); the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8).  This switching function prevents
remote control interference when operating several projectors or
video equipment at the same time.  
For example operating the projector in “Code 7”,  both the projector
and the remote control must be switched to “Code 7”.
To change the code for the projector;
Select a remote control code in this Setting Menu.
To change the code for the remote control;
Check the Reset Switch to Use position in the compartment lid
on back of the remote control.
And then while holding down the MENU button, press the IMAGE
button number of times corresponding to the remote control code
for the projector.
To reset the code for the remote control;
Slide the Reset Switch to Reset position in the compartment lid
on back of the remote control.
Remote control
When pressing the SELECT
button at Remote control, the
remote control code menu
appears.
Use positionReset position
Reset switch
Lamp counter reset
This function returns all setting values except the lamp
counter to the factory default settings.
Closes SETTING MENU.
Quit
Factory default
This function is used to reset the lamp replace counter. When
replacing the projection lamp, reset the lamp replace counter
by using this function. See page 45 for operation.
Select Factory default and this
box appears. Select [Yes], and
the next box appears. Factory default
Select [Yes] to activate it.
Remote control         
						

							42
APPENDIX
READYLAMP
LAMP
REPLACEWARNING
TEMP.
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from AC outlet.1
2
3
4
Pull out air filter from a projector.
Pulling up center frame of air filter top, separate air filter top and
air filter from air filter base.
Clean each parts with brush out dust and particles. Be sure to
dry them out.
Assemble sheet and air filter and replace air filter to a projector.5
AIR FILTER
AIR FILTER
TOP
AIR FILTER
BASE
AIR FILTER
CAUTIONDo not operate a projector with Air Filter removed.  Dust
may accumulate on LCD Panel and Mirror degrading
picture quality.
Do not put small parts into Air Intake Vents. It may result
in malfunction of a projector.
MAINTENANCE
WARNING TEMP. INDICATOR
Ventilation Slots of a projector may be blocked.  In such an event, reposition
a projector so that Ventilation Slots are not obstructed.
Air Filter may be clogged with dust particles.  Clean Air Filter by following
section AIR FILTER CARE AND CLEANING on this page.
1
2
If WARNING TEMP. Indicator remains on after performing above checks,
Cooling Fans or Internal Circuits may be malfunctioning. Contact the service
station.3
The Warning Temp. Indicator flashes red to let you know the internal temperature
of the projector exceeds the normal level. If the temperature goes up further, the
projector will be turned off automatically and the Ready indicator will go out. (The
Warning Temp. Indicator continues flashing.) After the cooling-off period, the
Ready Indicator lights on again and the projector can be turned on by pressing the
On/Off button on the remote control unit or on the side control. When you turn on
the projector, the Warning Temp. Indicator will go out.
If the Warning Temp. Indicator is still flashing, check the followings; FRONT INDICATORS
When both of the Warning Temp. and Ready indicators are flashing:
Warning Temp.
IndicatorReady
Indicator
When the projector detects an internal problem, it will shut down automatically and both of the Warning temp. and Ready
Indicators starts flashing. In this condition, the projector cannot be turned on even if you press the On/Off button on the
remote control unit or on the side control. If this case happenes, disconnect and reconnect the AC power cord, and then turn
on the projector again to check its operation. If the projector shuts down again or fails to be turned on, the internal check and
repair will be required. Plug off the AC power cord and contact service station.
WA R NING
TEMP. READY
LAMP
REPLACELAMP
REAR INDICATORS
Air filters help prevent dust from accumulating on the optical elements inside the projector. To whatever extent the air filters
become clogged with dust particles, the cooling fans’ effectiveness is reduced, which may result in an internal heat build-up
and adversely affect the life of the projector. Therefore, for appropriate care and use of the projector, regular cleaning of the
air filters is necessary.
How often the air filters should be cleaned really depends upon the environment in which the projector is being operated. As
a rough guide, under a normally clean operating environment, the air filters should be cleaned approximately every 200
hours of use. However, if the projector is being operated in a somewhat dusty or smoky environment, the air filters should be
cleaned more often; for consistently good projector operation and performance, timely cleaning of the air filters is a very
important factor. When appropriate, clean the air filters following the steps below.
NOTE: If the dust cannot be removed by
cleaning, it is probably time to replace
the air filters with new ones. Please
consult your dealer.
Air Filter Parts No.  610 301 4814 
						

							43
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function.  Lamp Management Function detects status of all lamps and shows status on screen or on LAMP
REPLACE indicator.  This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions. 
Projection Lamp lights normally.
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them
becomes out.  Check number of  lamp on Lamp Status Display and replace lamp.
Yellow Lamp
Dim Lamp
X Mark on Lamp
Red Lamp
LAMP REPLACE
INDICATOR
Projection Lamp is turned off.
Projection Lamp is nearing its end.  When image becomes
darker or color becomes unnatural, replace lamp.  (LAMP
REPLACE indicator lights yellow.)
(LAMP REPLACE indicator flashes yellow.)
Projection lamp is defective or fails to be turned on. Restart
a projector on, and make sure lamp is on. If this mark still
appears, replace lamp corresponding with number marked
X.LAMP STATUS
DISPLAY
1
4
3
2
Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp.
When any of 4 lamps becomes out, Lamp Mode is changed over from 4 lamps to 2 lamps.  And when any of 2 lamps are out,
a projector operates with 1 lamp.  Lamp Mode can be switched to 4 lamps or 2 lamps manually.  Refer to SETTING section
on page 39, 40
.
1
24
31
4
3
2
4 LAMP MODE2 LAMP MODE
(Example)
13
24
1 LAMP MODE
(Example)
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2, Input 3 or input 4).
This shows status of each lamp as; ON, OFF, NEAR END, or OUT.  Refer to following for each status.
20
LAMP STATUS
INPUT 1
1
24
3 
						

							44
APPENDIX
Check number of lamp to be replaced on Lamp Status Display.
Remove two screws on Lamp Cover and press button to open
Lamp Cover.  (See right figure.)
1
3
Loosen two screws and pull out Lamp Assembly to be replaced
by grasping handle.4
Turn off a projector and disconnect AC Power Cord.  Allow a
projector to cool down for at least 45 minutes.2
Replace Lamp Assembly with a new one and tighten two screws.
Make sure Lamp is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp Cover and tighten two screws. 
5
7
8
Connect AC Power Cord to a projector and turn a projector on.
Reset Lamp Replacement Counter. (Refer to section Lamp
Replace Counter on page 45.)
NOTE :Do not reset LAMP REPLACEMENT COUNTER when
lamp is not replaced.
BUTTON
SCREWS
LAMP
COVER
SCREWS
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.LAMP 1
LAMP 2LAMP 3
LAMP 4
CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY
RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing
all 4 lamps at a time. 
LAMP REPLACEMENT
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow.  If this indicator lights
yellow, replace the projection lamp with a new one promptly.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover.  The inside of a projector can
become very hot.
CAUTION
REAR INDICATORS
READYLAMP
LAMP
REPLACEWARNING
TEMP.
WA
RNING
TEMP. READY
LAMP
REPLACELAMP
FRONT INDICATORS
LAMP REPLACE
INDICATOR
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER.
WARNING: 
						

							45
APPENDIX
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer.  When ordering a Projection Lamp, give the
following information to the dealer.
●
Model No. of your projector   : PLC-XF46N/E
●Replacement Lamp Type No. : POA-LMP100
(Service Parts No. 610 327 4928)
Move pointer to Lamp counter reset and then
press SELECT button.  
Move arrow to
replaced lamp number (Lamp 1, Lamp
2, Lamp 3 or Lamp 4) and then press
SELECT button.
Be sure to reset Lamp Counter when Lamp Assembly is replaced.  When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear.  Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.1
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset” and then press 
SELECT button.2
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.4
Move arrow to replaced lamp number (Lamp 1, Lamp 2, Lamp 3
or Lamp 4) and then press 
SELECT button.  Message Lamp
replace counter Reset? is displayed. Move pointer to [Yes] and
then press SELECT button.3
NOTE:Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
Message Lamp replace counter Reset? is
displayed. Move pointer to [Yes] and then
press SELECT button.
1
24
3
Select [Yes] to activate it.
LAMP REPLACE COUNTER    
						

							46
APPENDIX
This projector uses a high-pressure lamp which must be handled carefully and properly.  Improper
handling may result in accidents, injury, or create a fire hazard.
●Lamp lifetime may differ from lamp to lamp and according to the environment of use.  There is no
guarantee of the same lifetime for each lamp.  Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual.  )  Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.  
●A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end.  Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately.  Contact an
authorized service station for a checkup of the unit and replacement of the lamp.  Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes.  Any broken shards found should be cleaned up carefully.  No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service.  Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.  
LAMP HANDLING PRECAUTIONS
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see TROUBLESHOOT-
ING section on page 47. To correct failure, try Solutions.
If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Pixelworks ICs used. 
						

							47
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING
PROJECTOR  on pages 13 ~ 16.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitors
display.Problem may be with your graphics controller rather than with a projector.  (When you reconnect a projector, be
sure to turn a computer and monitor off before you power up a projector.  Power equipment back on in order of : Projector
and computer.)
6. If problem still exists, check following chart.
No power.●Plug a projector into your AC outlet.
●Turn MAIN ON/OFF switch to ON.
●Press POWER ON/OFF switch to ON.
●Make sure READY Indicator lights.
●Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE :After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1.  LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
●Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, a projector cannot be turned on.
(See TURNING ON/OFF PROJECTOR section on page 23.)
●Check Projection Lamp.  (Refer to page 44.)
Image is out of
focus.●Adjust focus of a projector.
●Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens.  In such an event, leave a
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.●Check Ceiling / Rear feature.  (See “SETTING” section on page 39.)
Problem:Try these Solutions
Picture is
Top/Bottom
reversed.●Check Ceiling feature.  (See “SETTING” section on page 39.)
Some displays are
not seen during
Operation.●Check Display feature.(See “SETTING” section on page 39.)
No image.●Check connection between your computer or video equipment and a projector.
●When turning a projector on, it takes about 20 seconds to display an image.
●Check system that you select is corresponding with your computer or video equipment.
●Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
Remote Control Unit
does not work.●Check batteries.
●Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
●Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
●Check remote control code from Remote Control Unit.
(See “SETTING” section on page 41.) 
						

							48
APPENDIX
System (1)SVGA 1SVGA 2SVGA 3
Auto PC Adj.Fine sync.Total dotsHorizontalVerticalCurrent modeClampDisplay area
Display area - HDisplay area - VFull screenResetMode freeStore
Quit
StandardRealImage 1Image 2Image 3Image 4
Image AdjustContrastBrightnessColor Temp
RedGreenBlue
Gamma
Store
Quit
NormalTrueWideDigital Zoom +Digital Zoom –
0 - 31
On/Off
0 - 630 - 63
InputRGB (Analog)
RGB (Scart)
Go to System(1)
Input 2
Y, Pb/Cb, Pr/Cr
Computer Input
Input 3
Go to System(2)
Go to System(2)
Input 1
Video 
S-Video
PC Adjust
640 x 480720 x 400800 x 6001024 x 7681152 x 8641280 x 10241400 x 1050
Mode 1Mode 2Mode 3Mode 4Mode 5
Image Select
High
0 - 630 - 630 - 63
0 - 15
Image 1Image 2Image 3Image 4
Screen
1600 x 1200
Quit
Yes/No
Quit
Mid
ResetYes/No
RGB 
Low
XLow
Sharpness0 - 15
N/A
Go to System(2)
Computer Input/Video Input
✽N/A - - -not applicable
MENU TREE
Go to System(1)
Go to System(3)
Y/C
MODE 1
MODE 2
Quit
Noise reductionOff/On
ProgressiveOff/On
Input 4Go to System(1)
RGB (PC Digital)N/A
RGB (AV HDCP)N/A 
						

							49
APPENDIX
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Video Input
Auto
1080i/501035i720p575p480p575i480i
StandardCinemaImage 1Image 2Image 3Image 4
Quit
0 - 630 - 630 - 630 - 63
Off/On
Language
Image Select
System (3)
System (2)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0 - 630 - 630 - 630 - 150 - 15
Image 1Image 2Image 3Image 4
Screen
SettingEnglishGermanFrenchItalianSpanishPortugueseDutchSwedish
ChineseKoreanJapanese
On/Off
On/Off
On/Off
On/OffOn/Off
On/Off
On/Off
4 Lamp/2 Lamp
Code 1 
Yes / No
Keystone
Blue back
Display
Logo
CeilingRear
Power management
On start
Lamp mode
Remote control
Factory default
Yes/No
Quit
Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Quit
Quit
Russian
HighColor TempMidLow
XLow
Yes / NoLamp counter reset
Computer Input/Video Input
1080i/60
Off/OnNoise reduction
Normal
Normal/Auto/EcoLamp control
Quit
Wide 
						

							50
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.  
• • • on : red• • • dim• • • off• • • flashing : red
The projector is OFF.  (The MAIN switch OFF position or the
AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON-
OFF button.
The temperature inside the projector is abnormally high.  The
projector cannot be turned on.  When  the projector is cooled
down enough and the temperature returns to normal, the
READY indicator lights green and the projector can be turned
on.  (The WARNING TEMP. indicator keeps flashing.)  Check
and clean the Air Filter.
The projector is being cooled down. It cannot be turned on until
the READY indicator lights green.  
Projector Condition
The projector is operating normally. 
The projector is cooled down enough and the temperature
returns to normal.  When turning on the projector, the WARNING
TEMP. indicator stops flashing.  Check and clean the Air Filter.
Indicators
READYgreen
LAMPred
The projector detects an abnormal condition and cannot be
turned on.  Unplug the AC Power Cord and plug it again to turn
on the projector.  If the projector is turned off again, disconnect
the AC Power Cord and contact the dealer or the service center
for service and checkup.  Do not leave the projector on.  It may
cause electric shock or a fire hazard.
The projector is in the Power management mode. 
✽
✽
✽
✽
✽
✽
✽
WARNING
TEMP.
redLAMP
REPLACE
yellow
• • • on : green• • • flashing : green