Sanyo Pdg Dxt10l Projector User Manual

							
5. Using On-Screen Display 
62
Image options menu 
The Image Options menu is used to configure image options such as screen positioning and aspect ratio. Access the im-
age options menu in the Adjust menu. 
 
The following table lists all functions with a description and the defau\
lt setting. 
ITEM DESCRIPTION 
Screen Select Screen using ◄or► from the list (see page 63). 
Overscan Set the Overscan value using ◄or► (see page 63). 
PC adj. 
Adjust the position values using the slides. 
Horizontal: Adjusts the image location horizontally using ◄or►. 
Vertical: Adjusts the image location vertically using ◄or►. 
Total dots: Fine tune a computer image or remove any vertical banding that might appear. 
Fine sync: Adjust the clock phase or reduce video noise, dot or cross talk. 
Note: 
Only use the Phase settings after the total dots settings have been modified. 
  
						

							
5. Using On-Screen Display 
63 
 
Screen 
The screen option allows for the adjustment of the aspect ratio to alter the appearance or ratio of the projected image.  
 
4:3 – Standard TV screen (4:3), proportionally four units wide for every three units high, no matter the size of the screen. 
16:9 – A wide-screen aspect ratio for video. 
Side cut – Crops the image. 
True – Displays the current image in its true resolution. 
Normal – Displays the current image in its aspect ratio. 
 
Overscan 
Video images normally exceed the size of the display screen. The edge of the picture may or may not be displayed cor-
rectly. The border area that is cropped can be adjusted by using the Overscan menu. 
 
Set the overscan percentage between 0 – 15% to compensate for different screen sizes.  
						

							
5. Using On-Screen Display 
64
 
Video menu 
The Video menu is used to configure image options such as film. Access the Video menu in the Adjust menu. 
 
The following table lists all functions with a description and the default setting. A detailed description follows the table. 
ITEM DESCRIPTION 
Noise reduction Select Noise reduction mode (see page 65). 
3D Y/C separation Select 3D Y/C separation mode (see page 65). 
Progressive Select Progressive mode (see page 65). 
Color matrix Select Color matrix mode (see page 65). 
Film Select Film mode (see on page 65). 
 
  
						

							
5. Using On-Screen Display 
65 
 
Noise reduction 
Select the level of noise reduction required. 
 
Range: Off, Low, Mid, High. 
 
3D Y/C separation 
3D Y/C Separation separates composite signal to Y (brightness) signal and C (color) signal, and can help to produce 
clearer and sharper images without overlapping colors (rainbow effect). 
 
Set 3D Y/C Separation On or Off. 
 
Progressive 
Progressive converts an interlaced image to a progressive scan image. 
 
Select the form of Deinterlacing required from:  
Still – Select for stills such as slide projections or screen shots. 
Normal – Select Normal for non-specialized projection. 
Movie – Select for movie projection.  
						

							
5. Using On-Screen Display 
66
 
Color matrix 
Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color 
space. 
 
Select from the following: 
Auto – Auto selects the color matrix. 
RGB – Sets the color matrix to RGB, use for PC monitor or camera imaging. 
SDTV – Sets the color matrix to SDTV, use for Standard Definition imaging\
. 
HDTV – Sets the color matrix to HDTV, use for High Definition imaging. 
 
Film 
Film aids in converting motion picture film images into video. The process adds additional frames to the picture in order to 
increase the frame rate. 
Note:  
This feature is only available when Progressive is turned on and SDTV  
signal is selected. 
 
Select from the following: 
Off – Film mode is turned off. 
2-2/2-3 Auto – Detects pull-down correction method. 
2-2 On – Uses 2-2 pull-down correction method. 
2-3 On - Uses 2-3 pull-down correction method.  
						

							
5. Using On-Screen Display 
67 
 
s Detail Settings Menu Descriptions and Functions 
The Detail settings menu contains basic and advanced color adjustment options such as gamma correction, color contrast 
and color correction.  
Basic 
The Basic tab contains general Detail Settings such as gamma correction and color temperature. Access to the General 
tab is through the Detail Settings menu. 
 
The following table lists all functions with a brief description. 
ITEM DESCRIPTION 
Reference Set Reference mode (see page 68). 
Gamma Select Gamma Correction mode (see page 68). 
Color temp. Move the slider bar left or right to set the color temperature value in Kelvin (K). Compensate 
for the amount of light available. Daylight is approximately 5500K. 
BrilliantColor Move the slider bar left or right to set the BrilliantColorTM value. BrilliantColor extends the 
exposure range and sharpens detail for grain free images.  
  
						

							
5. Using On-Screen Display 
68
 
Reference 
The Reference mode allows the projector to differentiate between source materials for example movies, PC images or 
video stills. 
 
Select from the following: 
High-bright – Select for use in a brightly lit room. 
Presentation – Select if the projector is to be used for presentation purposes. 
Video – Select for video projection. 
Movie – Select for Movie projection. 
Graphic – Select Graphic for still images. 
sRGB – Select for projecting PC or web page images. 
 
Gamma 
Gamma enables adjustment to the light intensity (brightness) of an image in order to match the source more closely. 
 
Select from the following: 
Dynamic – Allows the projector to alter the gamma correction automatically. 
Natural – Attempts to emulate the original source as closely as possible. 
Black detail – Black detail highlights boundaries between light and dark areas of the image more clearly.  
						

							
5. Using On-Screen Display 
69 
 
White balance 
White Balance allows the projector to compensate for different colors of light being emitted by different light sources. 
 
The following table lists all functions with a brief description. 
ITEM DESCRIPTION 
Red Set the value to compensate for red light sources. 
Green Set the value to compensate for green light sources. 
Blue Set the value to compensate for blue light sources. 
Contrast R Set the Contrast R value to compensate for red light sources. 
Contrast G Set the Contrast G value to compensate for green light sources. 
Contrast B Set the Contrast B value to compensate for blue light sources.  
						

							
5. Using On-Screen Display 
70
 
Color correction 
The Color correction tab enables the adjustment of color values in an image to remove unwanted effects, improve color, 
characteristics or add more of a particular color. 
 
The following table lists all functions with a brief description. 
ITEM DESCRIPTION 
Red Increase or decrease the amount of red in the projected output using ◄ and ►. 
Green Increase or decrease the amount of green in the projected output using ◄ and ►. 
Blue Increase or decrease the amount of blue in the projected output using ◄ and ►. 
Yellow Increase or decrease the amount of yellow in the projected output using ◄ and ►. 
Magenta Increase or decrease the amount of magenta in the projected output using ◄ and ►. 
Cyan Increase or decrease the amount of cyan in the projected output using ◄ and ►.  
						

							
5. Using On-Screen Display 
71 
 
t Setting Menu Descriptions and Functions 
The Setup menus contain the most often used settings during installation and options to customize the general output of 
the projector. Three tabs are accessible through the Setup menu, general, installation and option. 
Basic 
The Basic tab contains general setup options such as lamp mode and OSD language settings and can be accessed with 
the projector control panel or with the remote control unit. 
 
The following table lists all functions with a brief description. 
ITEM DESCRIPTION 
Keystone Adjust the Keystone trapezoid (see Keystone page 72). 
Lamp control Select Lamp control. Range: Normal or Eco. 
Lamp mode Select Lamp configuration. Range: Dual, Lamp1 or Lamp2. 
Lamp interval Select Lamp interval. Range: Off, 1 week, 4 weeks or 2000 hours. 
Simple menu Displays menus with minimum essential options. This setting is best suited to novices. 
Language Select the OSD language (see Language on page 74).