Sanyo DP47840 Hdtv Lcd Owners Manual

							2Need help? www.sanyoctv.com              1-800-877-5032
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in 
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit fully into your outlet, consult an electri-
cian for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the 
manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the manu-
facturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13.  Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.15. If an outside antenna is connected to the television
equipment, be sure the antenna system is grounded so
as to provide some protection against voltage surges
and built up static charges. In the U.S. Selection 810-21
of the National Electrical Code provides information with
respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding elec-
trodes, and requirements for the grounding electrodes.
16. An outside antenna system should not be located in the
vicinity of overhead power lines or other electrical light
or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.”
17. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
19. When the MAINS plug is used as the disconnect device,
the disconnect device shall remain readily operable.
CAUTION
RISK OF ELECTRIC SHOCK   DO NOT OPEN!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL.THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS
UNIT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS 
						

							PC RESOLUTION CHART
3Need help? www.sanyoctv.com              1-800-877-5032
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a 
residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.  However,
there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following  measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void 
the user’s authority to operate the unit.
As an Energy Star ® Partner, Sanyo
Manufacturing Corporation has deter-
mined that this product meets the Energy
Star ® guidelines for energy efficiency.
TRADEMARKS
Manufactured under license from Dolby Laboratories.
“Dolby” is a trademark of Dolby Laboratories.
HDMI, the HDMI Logo and High-
Definition Multimedia Interface are
trademarks or registered trademarks 
of HDMI Licensing LLC in the United
States and other countries.
This Class B digital apparatus complies with Canadian
ICES-003.
Manufactured under license from
Audyssey Laboratories. U.S. and
foreign patents pending. Audyssey
Dynamic Volume
TM is a trademark of
Audyssey Laboratories. 
						

							4Need help? www.sanyoctv.com              1-800-877-5032
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS  . . . . . . . . . . . . . . . 2
FCC INFORMATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TRADEMARKS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
PC RESOLUTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
CONTENTS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SPECIFICATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PROTECTING THE LCD SCREEN  . . . . . . . . . . . . . . . . . . . . .4
HANDLING PRECAUTIONS  . . . . . . . . . . . . . . . . . . . . . . . . .4
POSITIONING THE LCD HDTV  . . . . . . . . . . . . . . . . . . . . . . .5
STAND REMOVAL/STAND ASSEMBLY  . . . . . . . . . . . . . . .5
WALL MOUNTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
GETTING STARTED—
Remote Control Battery Installation  . . . . . . . . . . . . . . . .5
Antenna Connections for off-air or cable  . . . . . . . . . . .5
BACK PANEL JACKS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
A/V CONNECTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
POWER CONNECTION / INITIAL CHANNEL SEARCH  . . .8
REMOTE CONTROL OPERATION  . . . . . . . . . . . . . . . . . . . . .9
ON-SCREEN MENU OPERATION—
Channel Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Channel Search  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Channel Scan Memory  . . . . . . . . . . . . . . . . . . . . . . .10
Input Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Video2 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Menu Language  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Digital Caption  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Energy Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Clock Timer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Light Sensor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Auto Shut-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Picture  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Manual Picture Settings  . . . . . . . . . . . . . . . . . . . . . .14
Pix-Shape Settings  . . . . . . . . . . . . . . . . . . . . . . . . . .15
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
aaManual Sound Settings . . . . . . . . . . . . . . . . . . . . . . .16
PC CONNECTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PC MENU OPERATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PHOTO VIEWER  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
WARRANTY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
PROTECTING THE LCD SCREEN
CAUTION: The screen can be damaged if it is not
maintained properly. 
•Do not use hard objects such as hard cloth or
paper to clean the screen.
•Do not use excessive pressure when cleaning the
screen; excessive pressure can cause permanent
discoloration or dark spots.
•NEVERspray liquids on the screen.
HANDLING PRECAUTIONS
•Handle by the cabinet only. 
•Handling by two or more people is recommended.
•Never touch the screen when handling.
•Handling damage is notcovered under warranty.
Please read before
operating your HDTV!
“The American Academy of Pediatrics discourages
television viewing for children younger than two
years of age”CONTAINS MERCURY LAMPS,
DISPOSE OF PROPERLY
SPECIFICATIONS
Power Requirement:  Source: AC 120V, 60Hz
AC Power Consumption: Weight:
221 watts 44.5 lbs.
Dimensions:
MODEL WIDTH HEIGHT DEPTH
DP47840 44.6 29.4 12.7
w/o stand27.2 4.6
NOTE: Dimensions are in inches 
						

							5Need help? www.sanyoctv.com              1-800-877-5032
1
Place HDTV face downon a padded or 
cushioned flat surface to protect the screen
and finish
2
Remove the four (4) screws securing the foot
stand. CAUTION:Hold the stand firmly as you
remove the last screw.
STAND REMOVAL ____________
GETTING STARTED
Install two (2) “AAA” batteries in the remote
control. (Not included)
To ensure safe operation, please observe the
following precautions:
• Replace both batteries at the same time. Do not use a
new battery with a used battery. 
• There’s a risk of explosion if a battery is replaced by
an incorrect type.
• Do not expose the Remote Control unit to moisture 
or heat.
• Be sure to match the “+”and “
–”signs on the 
batteries with marks inside the remote control.
ANTENNA CONNECTION FOR 
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLEANALOG / DIGITAL
ANTENNA IN
POSITIONING THE HDTV 
•Always use a firm and flat surface when 
positioning your HDTV. 
•Do not position the unit in a confined area. 
•Allow adequate space for proper ventilation.
•Do not position the HDTV where it is easily
reachable by small children and may present
risk of injury.
BATTERY INSTALLATION
Hook up your antenna or your cable service to
the HDTV’s ANTterminal with the use of a 75
OHM coaxial cable.
NOTE: Keep your indoor antenna at least 3 ft. away
from the television set and any other electronic
equipment.
The tuner in this HDTV can receive:
• Digital and Analog off air signals from an antenna
• Analog or ClearQAM cable channels from a direct
Cable TV connection.
1
Place HDTV face downon a padded or 
cushioned flat surface to protect the screen
and finish
2
Carefully insert the stand base to the bottom
of the HDTV and secure the base by inserting
4 screws as indicated in the above diagram.
NOTE: If your HDTV came packed with the Stand Base
unassembled, these screws will be found in the
literature package.
STAND ASSEMBLY ___________
Wall mounting of the HDTV must be performed
by a skilled person.
Use the screws you would use to attach the stand
base to secure the HDTV to a wall mounting kit
(not included.)
VESA standard interface:  400 x 400
Mounting screws measurements: 
M6 (6mm) Diameter, Length—12mm (maximum)
WALL MOUNTING ____________ 
						

							6Need help? www.sanyoctv.com              1-800-877-5032
GETTING STARTED
HDTV INPUT/OUTPUT REFERENCE
Composite
Component
NOTE: Composite, Component, and DVI video connections need their appropriate audio connections.
High Definition image available from HD signals and HD equipment.
Standard DefinitionHigh DefinitionOptimum
High Definition
H D M I
(or DVI to HDMI
cable/adapter)HDTV BACK PANEL
7
3
1
2
5
HDMI (INPUT1, INPUT2, & INPUT3)
An all digital AV interface that can accept uncompressed
video signals up to 1080p for the very best picture possible.
NOTE: A DVI connection is possible via the HDMI (DVI)
INPUT1 using an appropriate adapter and connecting
the audio signal to AUDIO mini stereo jack.
USB Input
View pictures stored in a USB flash drive.
PC Input
MONITOR RGB (D-SUB)
AUDIO mini stereo jack (3.5mm)
For AUDIO signal from PC or DVI device.
Analog / Digital Antenna Input
Component AV Input (VIDEO2 or VIDEO3)
Green (Y), blue (Pb), and red (Pr) Video inputs plus the white
and red Audio inputs.
NOTE:  A composite connection is possible via VIDEO INPUT2
using the Y (VIDEO) jack and the L/R audio jacks. (See
Video2 Setting on page 11.)
Composite AV Input (VIDEO1)
Yellow (Video), plus white and red (Audio) input jacks.
Digital Audio Output (Coaxial)
Analog Stereo Audio Out (L/R) Jacks
1
2
3
4
5
6
7
8
6
9
8
4
9 
						

							7Need help? www.sanyoctv.com              1-800-877-5032
GETTING STARTED
AUDIO / VIDEO CONNECTIONS
DVD PLAYER 
(or similar device)
VCR 
(or analog device)
MULTICHANNEL
RECEIVER
NOTE: Audio/Video cables
are not supplied
COMPONENTconnections will accept
SDTV, EDTV and HDTV video signals.
Use them for great image quality
from digital devices such as a DVD
player or Video Game system.
SATELLITE RECEIVER
(or similar device)
USB FLASH
DRIVE
HDMI (DVI) INPUT1 can be used to
hookup a DVI device with the use of
an appropriate DVI to HDMI cable or
adapter.
NOTE: Stereo Mini AUDIO jack needs to
be hooked up to the DVI device as
well.
USB input jack is used to
connect a USB mass storage
device to watch digital
images (JPEG only.)
DVI
Use HDMI INPUT1, 2 & 3to hookup HD digital
devices such as a Blu-ray player, HD Cable Box,
HD Satellite Receiver or Video-game System.
Audio Output L/R are used to hookup an
external stereo Amplifier. (Do not connect
external speakers directly to the HDTV)
STEREO
AMPLIFIER
COMPOSITE connections are used to hookup
your analog equipment such as a VCR or an
older DVD player.
NOTE: Always match the color of your device’s output
jack, the connector and the HDTV’s input jack.
Digital Audio Output is used to
hookup a multichannel receiver
with the use of a phono-type
digital audio cable.
DVD PLAYER 
(or similar device) 
						

							8Need help? www.sanyoctv.com              1-800-877-5032
TURN ON TV (PRESS POWER BUTTON)
Wait for on-screen instructions to set an Initial Energy
Saving Mode, and perform an Initial Channel/Signal
Search.
PLUG IN AC POWER CORD
120V AC, 60Hz
GETTING STARTED (CONTINUED)
INITIAL CHANNEL SEARCH
Before proceeding, please make sure to hook up
your antenna or cable connection and all AV
equipment correctly to your HDTV.
Press the CHkey to perform a channel
search from an Antenna or a direct Cable
connection, and a signal search from devices
hooked up to the HDTV’s AV input jacks.
AV INPUT SELECTION
Press the INPUTkey to select the correct AV
input for the video source you wish to watch.
TV SET LOCATION SELECTION:
Select “Home Mode” by pressing the CHkey to set
the HDTV’s backlight to an Energy Star qualified level,
or select “Store Mode” by pressing CHto set the
backlight to a retail display level.
CHANNEL AND AV SIGNAL SEARCH:
CHANNEL AND SIGNAL SETUP SCREEN
The final setup screen displays analog and digital
channels found as well as AV inputs detected. Pressing
the CHkey finalizes the setup process.
NOTE: To repeat the initial setup process press the MENU key.
INITIAL CHANNEL/SIGNAL SEARCH
SETUP SCREEN
CHANNEL SEARCH PROGRESS SCREEN
INITIAL ENERGY SAVING
MODE SCREEN
CHANNEL/SIGNAL LIST SCREEN 
						

							9Need help? www.sanyoctv.com              1-800-877-5032
REMOTE CONTROL OPERATION
• PIX SHAPE Key—Cycles through the available
aspect ratios. The different settings either
stretch, zoom, or fill the image on your screen.
Bars may appear on top and bottom of your
screen (or on left and right sides) depending on
the broadcasted signal or program. (See page
15)
• DYN VOL Key—Modifies the Dynamic Volume
feature settings (see page 16.)
• MENU—Displays or hides the on-screen menu.
• HELP—Displays on-screen Help menu.
• Cursor (UP)(DOWN) keys—Move the on-
screen cursor up and down.
• Cursor (LEFT) (RIGHT) keys—Move the on-
screen cursor left and right.
• ENTER Key—Set or select the highlighted option
on the screen.
• EXIT Key—Exits the on-screen menu. • POWER Key—Turns your HDTV On or Off.
• INPUT Key—Selects the video source to view.
Holding down the key displays the Input List.
• ECO Key—Modifies the Energy Saverlevel (see
page 12.)
• AUDIO Key—Selects the desired Audio mode.
Stereo, Mono, or SAP (when available.)
• ON TIMER Key—Displays the current switch on
time (see Clock Timeron page 12.)
• CAPTION Key—Cycles through the available
Caption modes.
• RESET Key—Pressing it twice restores your
HDTV to its factory settings. All user customized
settings will be cleared.
• SLEEP Key—Displays the “Off” Timer. While Off
Timer is on-screen, press the “0” key to Set the
amount of time (in 30 minute increments) at
which the HDTV will turn off.
• NUMERICAL Keys—Select channels directly.
NOTE: For channels 100 and up, press and hold the
first number, then enter the remaining two numbers.
• Channelkeys—Scan through the channels
in the memory database.
• Volume 
+
+– –keys—Increases or decreases the
audio level.
• RECALL Key—Switch between current channel
and last selected channel.
• 
– –(sub ch) key —Allows for the direct selection
of  digital subchannels. For example: to select
channel 39.1 press the 
3and 9 keys followed by
the dash 
– –, and 1keys.
• MUTE Key—Mute or restore the sound.
• INFO Key—Displays the Channel Information
banner. 
						

							10Need help? www.sanyoctv.com              1-800-877-5032
CHANNEL SCAN MEMORY SCREEN
INPUT SETTING SCREEN
MAIN MENU SCREEN
CHANNEL SETTING SCREEN
CHANNEL SETTING___________
Auto –Searches the detected mode, Cable or Air.
Cable –Searches for analog and unscrambled
(ClearQAM) digital cable channels.
Air (Antenna) –Searches for analog and digital off-air
channels.
Digital Add-On –Searches digital off-air channels
adding newly found digital channels to the channel
map database.
Channel Search
Display the On Screen menu and use the
CURSORkeys to select Channel Setting.
Press ENTER.
NOTE: Digital Add-On option is not available when the cur-
rent mode is Cable.
ON-SCREEN MENU OPERATION
Channel Scan Memory lists all Analog and Digital
channels found. It also lists Analog channels that were
not found, which can be added.
Use the CURSORkeys to move the channel select
bar through all enabled and disabled channels, or use
the CHkeys to skip all disabled channels.
Press ENTERto enable or disable the selected channel.
Channel Scan Memory
NOTE: For information on local digital channels, visit
www.antennaweb.org
IMPORTANT FACT:This HDTV maintains only one database of
digital channels. Therefore, when you search for cable chan-
nels, the database of antenna digital channels will be deleted.
You will only be able to receive those ClearQAM channels your
cable company provides. 
Input Setting feature allows the removal of unused
inputs from the AV input loop.
Use the CURSORkeys to select an AV input. Press
ENTERto disable (uncheck) or enable (check) the high-
lighted  input.
NOTE: At least one input must and will remain checked.
:Skip is for reference only.
Input Setting