Sanyo CE42LH2WP Lcd Monitor Instruction Manual

							11
INSTALLATION MODE
Installation Mode
Installation Mode
On program
Tuner Menu
Max Volume
Winter mode
RC inhibition
Child Lock
Address
Baud rate
Panel protection
AV Auto shut off
Network Standby
On Timer Function
LED light setting
DCR
Network initial
Temperature Error
IP Address
Subnet
Gateway
DNSOff
Off
63
Off
Off
Off
0
19200
Off
Off
On
Off
Off
Off
>>>
0
000000000000
000000000000
000000000000
000000000000G2.02 0000
Select Adjust
MENUExit
This LCD monitor allows you to set up the following:
SETTING PROCEDURE
1.Press and hold the GREEN button on the remote control for 5 
seconds. (Installation Mode will appear)
2.Use the  or button to highlight each option, use the  or 
button to adjust each option. Press the MENU button to exit 
the mode.
N On ProgramSelect ON program using the  or button, select the start up 
position using the  or buttons.
2II$95*%$9$93&9,RU1HWZRUN
N Max VolumeSelect Max volume using the  or button, use the  or 
buttons to set the maximum volume required.
N Winter modeThis Function can be activated when the LCD monitor is used dur-
LQJFROGWHPSHUDWXUHFRQGLWLRQVDSSUR[LPDWHO\
						

							12
OPERATION
6HOHFWLRQRISLFWXUHVL]H
Select screen size from FULL, FULL ALL, ZOOM 16:9, TITLE IN 16:9, 
ZOOM 14:9, TITLE IN 14:9, NORMAL or NATUR AL WIDE by pressing 
the WIDE button repeatedly on the Remote Control.
When in AV2 (RGBHV) or PC mode FULL or NORMAL can be 
selected.
Note: Full - Set display area 100%
Only in DVI or AV2 (YPbPr) displaying high resolution content 
FULL and FULL ALL are selectable.
Note:FULL - Set display area 95%
FULL ALL - Set display area 100%
All other inputs AV1, AV3, DVI or AV2 (YPbPr) (displaying lower reso-
lutions) can select all picture sizes.
N Full/Full All
N Zoom 16:9
N Title in 16:9
N Zoom 14:9N Title In 14:9
N Normal
N Natural Wide
4:3 14:9 16:9 Letterbox Video
The whole screen 
LV
						

							13
OPERATION
PIP/POP Operation
Using this function, you can enjoy a DVI or Network program and an 
image (AV1,AV2,AV3 or PC input) at the same time.
Press the ON/OFF button on the Remote Control repeatly to select 
PIP1,PIP2,POP or OFF mode.
During the PIP/POP mode, press the Main/Sub Picture Swap but-
ton will switch the location for main and sub picture.
Only the sound on the main picture is heard from the monitor 
VSHDNHU7KHVRXQGRQWKHVXESLFWXUHFDQQRWEHKHDUG
The details for PIP/POP operation (eg,location for sub picture or 
input source for any picture,etc.), please refer to page 10.
N PIP1 mode
N OFF modeN PIP2 mode
N POP mode
The left picture is main picture, the right picture is sub picture.
GBGB 
						

							14
OPERATION (IN TEXT MODE)
Teletext Operation
Teletext is only available via external sources.
Teletext mode can be operated by the following buttons on the Re-
mote Control.
Some buttons have dual functions.
TXT/TV
Press TXT/TV button to select teletext. Press again will display: 
AV mode: AV/TEXT mode/MIX mode/AV.
Note:
MIX mode:AV (broadcast image) screen and the contents of TEXT 
(superimposed) are displayed simultaneously.
CANCEL mode:TEXT/MIX MODE is cancelled temporarily and AV 
image is displayed.
If the signal is removed or disconnected, the monitor will revert to a 
EOXHEDFNJURXQGZLWK
						

							15
SPECIFICATIONS/HELPFUL HINTS
6SHFL
						

							16
DIMENSIONS
989.0
1027.0
165.9418.4 418.4
200.0 400.0
200.0 400.0
100.0
41.8 126.0
50.8
17.6 953.0
402.9
417.9
292.0
300.6
178.5
43.7 930.25925.4
(WALL MOUNT SCREW )
10 x M6, 1.0 PITCH x 12MM
ø4.2
(RC RECEIVER) VIEWING AREA(H)
620.0
546.0
523.0
VIEWING AREA(V )
Control buttons
ø4.2
(LED INDICATOR)Handles x 2
Cables exit terminal cover
Unit: mm
N CE42LH2WP
GBGB 
						

							17
PC/DVI-D/COMPONENT SIGNAL SUPPORT TIMING LIST
N DVI-D signal support timing
N Component signal support timing
Resolution+RUL]RQWDO
Frequency 
N+]Vertical 
Frequency 
+]Remark
720 x 480 15.735 60i SDT V 480i
720 x 576 15.625 50i SDT V 576i
720 x 480 31.25 60p SDT V 480p
720 x 576 31.25 50p SDT V 576p
1280 x 720 45.00 60p HDT V 720p
1280 x 720 37.50 50p HDT V 720p
1920 x 1080 33.75 60i HDT V 1080i
1920 x 1080 28.13 50i HDT V 1080i
Resolution+RUL]RQWDO
Frequency 
N+]Vertical 
Frequency 
+]Remark
640 x 480 31.43 59.88 VGA VESA 60Hz
640 x 480 37.86 72.81 VGA VESA 72Hz
640 x 480 37.5 75 VGA VESA 75Hz
640 x 480 34.97 66.6 MAC LC 13"
640 x 480 35 66.67 MAC_NORMAL 13"
800 x 600 35.16 56.25 SVGA VESA 56Hz
800 x 600 37.88 60.32 SVGA VESA 60Hz
800 x 600 46.875 75 SVGA VESA 75Hz
832 x 624 49.72 74.55 MAC_NORMAL 16"
1024 x 768 48.36 60 XGA VESA 60Hz
1024 x 768 60.23 75.03 XGA VESA 75Hz
1024 x 768 56.47 70.07 XGA VESA 70Hz
1024 x 768 60.24 75.08 MAC_NORMAL 19"
1152 x 870 68.68 75.06 MAC_NORMAL 21"
1280 x 1024 63.98 60.02 SXGA VESA 60Hz
720 x 480 31.7 59.94 480p
720 x 480 15.73 59.94 480i
768 x 575 31.25 50 575p
768 x 575 15.63 50 575i
1280 x 720 37.5 50 720p - 50Hz
1280 x 720 45 60 720p - 60Hz
1366 x 768 48.36 60 WXGA
1360 x 768 47.7 60 WXGA
1920 x 1080 28.125 50 1080i - 50Hz
1920 x 1080 33.75 60 1080i - 60Hz
1920 x 1080 56.25 50 HDT V 1080p - 50Hz
1920 x 1080 67.5 60 HDT V 1080p - 60Hz
1920 x 1080 27.00 24 HDT V 1080p - 24Hz
1920 x 1080 28.13 25 HDT V 1080p - 25Hz
1920 x 1080 33.75 30 HDT V 1080p - 30Hz
N PC signal support timing
Resolution+RUL]RQWDO
Frequency 
N+]Vertical 
Frequency 
+]Remark
720 x 400 31.47 70.09 DOS (VGA)
640 x 480 31.43 59.88 VGA VESA 60Hz
640 x 480 37.50 75.00 VGA VESA 75Hz
640 x 480 37.86 72.81 VGA VESA 72Hz
640 x 480 43.27 85.00 VGA VESA 85Hz
640 x 480 35.00 66.67 Mac. 13
640 x 480 34.97 66.60 Mac LC 13"
800 x 600 35.16 56.25 SVGA VESA 56Hz
800 x 600 37.88 60.32 SVGA VESA 60Hz
800 x 600 46.875 75.00 SVGA VESA 75Hz
800 x 600 34.50 55.38 SVGA
800 x 600 38.00 60.51 SVGA
800 x 600 53.67 85.06 SVGA VESA 85Hz
832 x 624 49.72 74.55 Mac. 16
1024 x 768 48.36 60.00 XGA VESA 60Hz
1024 x 768 56.47 70.07 XGA VESA 70Hz
1024 x 768 60.02 75.03 XGA VESA 75Hz
1024 x 768 48.50 60.02 XGA
1024 x 768 60.31 74.92 XGA
1024 x 768 61.0 0 75.70 XGA
1024 x 768 68.68 85.00 XGA VESA 85Hz
1024 x 768 60.24 75.08 MAC_Normal 19"
1280 x 720 37.5 50.00 720p - 50Hz
1280 x 960 60.00 60.00 SXGA VESA 60Hz
1280 x 1024 79.976 75.025 SXGA VESA 75Hz
1280 x 1024 63.370 60.01 SXGA
1280 x 1024 63.34 59.98 SXGA
1280 x 1024 63.74 60.01 SXGA
1280 x 1024 63.79 60.18 SXGA
1280 x 1024 63.90 60.00 SXGA
1280 x 1024 81.13 76.107 SXGA
1152 x 900 61.20 65.20 SXGA
1152 x 900 61.85 66.00 SXGA
1152 x 900 71.40 75.60 SXGA
1400 x 1050 65.35 60.12 SXGA +
1400 x 1050 65.12 59.90 SXGA +
1152 x 870 68.68 75.06 MAC_Normal 21"
1280 x 1024 80.00 75.00 Mac II
1600 x 1200 75.00 60.00 UXGA VESA 60Hz
1366 x 768 48.36 60.01 WXGA
1360 x 768 47.73 60.03 WXGA
1920 x 1080 28.125 50.00 1080i - 50Hz
1920 x 1080 33.75 60.00 1080i - 60Hz
The monitor can be automatically adjusted in pc mode when receiving a stan-
dard VESA signal. It will be displayed as XGA when the monitor is receiving a 
XGA or WXGA signal.Depending on the condition of signals and the type and length of cables, these 
signals may not be properly viewed.
To save the XGA Mode 1366 x 768 setting switch the monitor off then on using 
the standby button.
GBGB 
						

							18
RS232C COMMAND TABLES
N Functional Execution Command Table
Command Item
C00 POWER ON
C01 POWER OFF
C03 POWER ON/ OFF (toggle)
C10 Wide toggle
C22 Input
C24 Wide “Natural” direct
C25 Wide “Zoom 16:9” direct
C26 Wide “Title in 16:9” direct
C27 Wide “Zoom 14:9” direct
C28 Wide “Title in 14:9” direct
C29 Wide “Full” direct
C30 Picture
C0F Wide “Normal” direct
C70 AV1 direct
C71 RGB direct
C72 AV2 RGBHV direct
C73 AV2 YPbPr direct
C74 AV3 direct
C75 DVI direct
C76 PC direct
C64 PC Auto adjust
C92 Factory settings
CF PSAVE ON Power save ON
CF PSAVE OFF Power save OFF
CF CLOK ON&KLOGORFN21
CF CLOK OFF&KLOGORFN2))
CF DEA RMCY RC inhibition OFF
CF DEA RMCN RC inhibition ON
N Image control Read Command Table
Status read command Item
CR BRIGHT  Status of Brightness.
CR CONT  Status of Contrast.
CR COLOR  Status of Color.
CR TINT  Status of Tint.
CR SHARP  Sharpness.
CR WBAL Status of White Balance Mode informa-
tion.
CR WBAL-R  Status of White Balance Red.
CR WBAL-G  Status of White Balance Green.
CR WBAL-B  Status of White Balance Blue.
CR NZRED  Status of Noise reduction setting.
CR FILM  Status of Film mode setting.
CR IMAGE Status of Image selection.
(The same as PICTURE mode)
CR DCDI  Status of DCDi setting.
CR ACCACM  Status of ACC/ACM setting.
CR CCS Status of CCS setting.
CR MPEGNR  Status of MPEG NR setting.
N PC Read Command Table
Status read command Item
CR H-POS Status of Horizontal position.
CR V-POS Status of Vertical position.
CR PHASE Status of PHASE value.
CR CLOCK Status of CLOCK value.
N Input Read Command Table
Status read command Item
CR INPUT Status of Input selection.
CR SOURCE Status of Input source mode.
CR SYSTEM Status of system of Input mode.
N Screen Read Command Table 
Status read command Item
CR SCREEN Status of screen size.
(The same of WIDE mode)
GBGB 
						

							19
RS232C COMMAND TABLES
N Time Read Command Table
Status read command Item
CR PANELH Status of accumulated lifetime of panel.
(The same as CR _LAMPH Command)
CR MONHStatus of accumulated lifetime of monitor.
7KHVDPHDV&5 B352-+&RPPDQG
N UK5 Read Command Table (Basic Command)
Command Item Note
CR0 Power On, Standby, power error,
CR1 Input M ode AV1, AV2, . . . , DVI, PC
CR WIDE Wide mode Auto, Normal, Full, . . .
CR PICTURE Picture mode Dynamic, Standard, . . .
CR SIGNAL Signal existence Signal/No signal
CR CHILD&KLOGORFNOn/Off
CR PSAVE Power save On/Off
CRTM Panel usage time –––
CR RMC RC inhibition On/Off
CR MDL Model number Model number
N Error code Table
Error code Note
?• Receiving the data that cannot be decoded.
• The wrong indication of parameter.
:URQJ
						

							N7R AK / N7RBK / N7RPK6$1