Sanyo CE42LH2WP Lcd Monitor Instruction Manual

							INSTRUCTION MANUAL CE42LH2R
CE42LH2DPB
CE42LH2WP
LCD Monitor
Please read this Instruction book before using your LCD monitor. 
We wish you many hours of pleasure from your new LCD monitor. 
						

							2
TABLE OF CONTENTS ........................ 2
SAFETY PRECAUTIONS ....................... 3
Installation and Use.............................. 3
SERVICING .................................. 4
Servicing ...................................... 4
Federal Communications Commission Notice ......... 4
AC Power Cord Requirement ...................... 5
End-User License ............................... 5
INSTALLATION .............................. 6
Step: 1 Mains Connection......................... 6
Step: 2 Connections ............................. 6
Remote control ................................. 7
Remote control battery installation .................. 7
Controls and Menus ............................. 8
Menu Operation................................. 8
Picture menu................................... 8
MENU OPERATION ........................... 9
Picture menu................................... 9
Sound menu ................................... 9Time menu..................................... 9
Setup menu.................................... 9
PC Adj. menu...................................
10
INSTALLATION MODE ........................11
Installation Mode................................11
OPERATION ................................ 12
Selection of picture size ..........................12
PIP/POP Operation..............................13
OPERATION (IN TEXT MODE) ................. 14
Teletext Operation...............................14
SPECIFICATIONS/HELPFUL HINTS ............. 15
6SHFL
						

							3
CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but 
LPSURSHUXVHFDQUHVXOWLQSRWHQWLDOHOHFWULFVKRFNRU
						

							4Servicing
Your monitor is fully transistorised and does not contain any user ser viceable components. 
You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage 
objects or even endanger people. Leave all required repair and ser vice jobs to an authorised ser vice technician. He will exclusively 
use such spare par ts that are complying with the same safety standards as applicable to the original par ts. The use of original 
VSDUHSDU WVFDQSUHYHQW
						

							5 AC Power Cord Requirement
The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you 
purchase it.
AC Power Cord for the United States and Canada:
$&3RZHU&RUGXVHGLQWKH8QLWHG6WDWHVDQG&DQDGDLVOLVWHGE\WKH8QGHU ZULWHUV/DERUDWRULHV8/DQGFHUWL
						

							6Step: 1 Mains Connection
N&RQQHFWWKHGLVSOD\XQLWWR9*$%1&DQG6FDUWFRQ-
nector as required.
1.Connect the in-line power connector to the Mains Inlet as shown 
above.
2.Connect the power cord of the LCD monitor to a suitable wall outlet.
As this product does not have a mains On/Off switch, please 
ensure your mains plug is easily accessible.
The LCD monitor is prepared for a mains voltage AC100 ~ 240V, 
50Hz/60Hz. To completely switch off the mains, or when the 
display unit is not to be used for an extended period of time, it is 
advisable to disconnect the power cord from the power outlet.
Please use the correct mains lead supplied with the set for your 
area.
3. Warning: To prevent injury, the unit must be securely attached to 
the wall in accordance with the installation instructions.
WARNING! High voltages are used in the 
RSHUDWLRQRIWKLVVHW5HIHUVHUYLFHWRTXDOL
						

							7
InputTo switch input source from AV1,RGB,AV2,AV3,
PC,DVI or Network mode.
StandbyTo switch the monitor on and off. Also see page 8.
MenuTo enter and exit the main menu, and sub menu.
WideTo select the screen mode Full,Full All,Zoom 
16:9,Title in 16:9,Zoom 14:9,Title in 14:9,
Normal or Natural wide.
Refer to page 12.
RecallTo display input selection information and the Time 
set.
You can also select colour systems in AV1/AV3 
mode as follows: AUTO
íPA LíSECAMíNTSCíNTSC4.43íPAL MíPAL N.
Auto PCIt can also be automatically adjusted in PC mode 
by pressing this button for twice .
BackUsed to return to the previous menu.
Up and DownTo select the next or previous item.
Sound Mute7RPXWHWKHVRXQGIURPWKHVSHDNHUV
The sound changes as follows: Normal volume 
Mute.
Bass ExpanderTo get an emphasised bass sound ON or OFF.
TXT/TVTo select Teletext mode.
Main/Sub Picture SwapTo swap Main and Sub picture.
ON/OFFTo  s w i t c h  OFFíPIP(1)íPIP(2)íPOP mode 
in turn.
Refer to page 13.
Level Up/DownTo adjust the sound volume level or enter sub 
menus.
F/OK7RFRQ
						

							8
INSTALLATION
Controls and Menus
qw
åThe LCD display has a Standby light to show there is power.
Switching into/from standby mode
The Standby mode is used for switching the LCD monitor off for short 
periods of time. In standby mode the monitor is switched off but is still 
receiving mains power.
LTo turn the monitor into standby mode, press the button.
The blue power indicator illuminates more brightly.
LTo turn the monitor ON from standby mode, press the button
again.
,I\RX
						

							9
MENU OPERATION
Picture menu
NAdvanced settings
Use the  or button to select Advanced settings and press 
the  or button to enter the sub menu as follows.
DCDi (Directional Correlational Deinterlacing) is used to process 
moving angled edge in deinterlacing to get the smoothest and most 
natural image. Press the  or button on the remote control to 
select On or Off.
ACC/ACM (ACC: Adaptive Contrast and Color; ACM-II: Active Color 
Management-II) is used to select adaptive Brightness, Contrast and 
tone control. Press the  or button on the remote control to 
select suitable mode either Vivid,Cinema,Sport or Off.
CCS (Cross Color Separation) is used to remove residual chroma 
information from luminance signal which is the result of imperfect 
decoding of composite video. Press the  or button on the 
remote control to select either Auto,Standard or Off.
DNR (Digital Noise Reduction) is available for noise reduction. Press 
the  or button on the remote control to select either Auto,
Low,Mid,High or Off.
MPEG NR (MPEG Noise Reduction): Removes unwanted ringing and 
EORFNQRLVHIURPLPDJHVWKDWKDYHXQGHUJRQH03(*RU-3(*FRP-
pression and decompression. Press the  or button on the 
remote control to select On or Off.
Film Mode,QYHUVHSXOOGRZQ)LOPYV9LGHRHWHFW
						

							10
MENU OPERATION
Language is used to select the preferred language. Use the  or 
button to select English,French,German,Italian,Spanish or 
Dutch.
H-Position changes the OSD position horizontally by using the 
or button.
V- Position changes the OSD position vertically by using the  or 
button.
Duration is used to set the display time of the MENU by using the 
 or button. (5 ~ 120 seconds)
Transparence is used to adjust transparence of menu display. Use 
the  or button to adjust levels.
N PIP/POP SetupUse the  or button to select PIP/POP Setup and press the 
 or button to enter the sub menu.
PIP/POP Mode: Using the  or button select the most suit-
able mode PIP1,PIP2,POP or Off. (Please refer to page 13.)
When Mode is set to Off,Sub Source and PIP Position will not 
ZRUN
Main Source is used to select input source (AV1, RGB, AV2, AV3, PC, 
9,RU1HWZRUNIRUPDLQSLFWXUHE\XVLQJWKH or button.
Sub Source is used to select input source (AV1, AV2, AV3, PC or 
DVI) for sub picture by using the  or button.
For a combination of main picture and sub picture: only DVI or 
1HWZRUNLQSXWFDQDVVHPEOHZLWKRWKHULQSXWVRXUFH)RUH[DPSOH
if main source is selected as AV1 input, then the sub source must 
EH9,RU1HWZRUNLQSXW
PIP Position: Using the  or button it can be selected To p
Left,Top Right,Bottom Right or Bottom Left.
N Initial SettingsThis function returns all setting values except for Installation Mode.
N Text LanguageUse the  or button to select Te x t  L a n g u a g e and press the 
 or button to select Western, Eastern, Russian, Arabic or 
Farsi.
N Tile Mode This function allows you to split an image to suit your monitor grid 
format to create a video wall.
Use the  or  button to select Tile Mode and press the  or 
button to enter the sub menu as follows.
Tile Mode Active can be set On or Off using the  or but-
ton.
H_Sets is used to divide the horizonal picture into more than one 
part, but the most is 5 parts (5 monitors).
V_ Set s is used to divide the vertical picture into more than one part, 
and the most is also 5 parts (5 monitors). Using the  or but-
ton to set.
H Location is used to select one part of the horizonal picture to dis-
play on the current LCD Monitor using the  or button.
V Location is used to select one part of the vertical picture to display 
on the current LCD Monitor using the  or button.
%H]HO+$GMXVWPHQW is used to align the image horizontally with 
respect to the other monitors in the video wall to accommodate the 
bezel width using the  or button. (0 ~ 10) 
%H]HO9$GMXVWPHQW is used to align the image vertically with respect 
to the other monitors in the video wall to accommodate the bezel 
width using the  or button. (0 ~ 10)
N AV2 SettingUse the  or button to select AV2 Setting and press the 
or button to select YPbPr or RGBHV.
Connect your PC to either PC-IN or RGBHV on the rear of the set.
Once connected select PC mode or AV2 (RGBHV, see page 6 for AV2 
input settings) via the INPUT button on your remote control.
The set will become a monitor for the PC.
NXGA ModeUse the  or button to select XGA Mode and press the  or 
button to select XGA or WXGA 1366 x 768.
N PC Power SaveThe monitor set automatically turns off with no PC input signal and 
ZDNHVXSZLWKVLJQDOZKLOH3&3RZHU6DYHLVDFWLYH
Use the  or button to select PC Power Save and press the 
 or button to select ON or OFF.
PC Adj. menu
Press the MENU button and select PC Adj. using the  or 
buttons, press the  or button to enter. Press the BACK 
button to return to the previous menu. Press the MENU button to 
exit menu operation.
Auto Adjust is used to automatically detect incoming signal, and 
adjust itself to optimize its performance by using the  or 
button. If the image is not displayed properly, a manual adjustment is 
required (Refer to following adjustments).
H-Position is used to move the horizontal picture position by using 
the  or button.
V- Position is used to move the vertical picture position by using the 
 or button.
ClockLVXVHGWRHOLPLQDWH