Sanyo Ce32fd90b User Manual

							English   - 30 -
 
Automatic Channel Scan 
  Automatic channel scan is started by pressing 
OK button while Automatic channel scan item 
is highlighted. 
  The following message appears on the 
screen: 
 
 
  Highlight Yes or No by using “
” or “” buttons 
and press  OK 
 button to confi rm.
If Yes is selected, automatic search starts.
Selecting No cancels automatic search.
After search is completed for digital channels, a 
message asking whether to search for analogue 
channels appears on the screen: 
 
 
  Press the OK button to search for analogue 
channels. The following menu appears on the 
screen for analogue channel search: 
 
   Select your  Country 
,  Language 
 and  Text 
language 
 by using “
” or “”  and  “” or “” 
buttons. Press  OK 
 or  RED 
 button to continue. To 
cancel, press  BLUE 
 button. The following menu 
will be displayed during the automatic tuning: 
 
 
  After APS  is fi nalized, the programme table 
will appear on the screen. In the programme 
table you will see the programme numbers and 
names assigned to the programmes.
If you do not accept the locations and/or the 
programme names, you can change them via 
the program table. 
  Manual Channel Scan 
  In manual channel scan, the number of the 
multiplex is entered manually and only that 
multiplex is searched for the channels. For every 
valid channel number, signal level and signal 
quality are shown on the screen.
In both manual and auto search any existing 
channel in the database is not re-stored to avoid 
redundant duplicates of that channel. 
Clear Service List (*)
(*) This setting is visible only when the Country 
option is set to Denmark, Sweden, Norway or 
Finland.
Use this setting to clear channels stored. Press 
“
” or “” button to select Clear Service List and 
then press OK. The following OSD message will 
be displayed on the screen:
Press OK to cancel. Select Yes by pressing “
” or “” button and press OK to delete all of 
the channels.
  First Time Installation 
  The user can use this item to load default 
settings, which were loaded to the receiver at 
the factory.
To install factory settings, highlight “First Time 
Installation” menu item and press  OK 
 button, 
then you will be asked whether or not to delete 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   30MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3015.04.2009   18:56:5115.04.2009   18:56:51 
						

							English   - 31 -
the settings. Selecting “Yes” by pressing  OK 
 
button while the “Yes” is highlighted will delete 
the existing channel table.
Then you will be asked to confi rm for deleting 
all channels and settings: 
 
 
  By selecting Yes and pressing the  OK 
 button, 
the existing channel table will be deleted.
After factory settings are loaded, “First Time 
Installation” menu will be displayed.
The menu which is displayed for language 
selection appears on the screen at fi  rst. By using  
“
” or “” buttons, select the desired language 
option, and press OK button to activate. 
  After then, “First time installation” OSD will 
appear on the screen. By pressing “
” or “” 
buttons, select the  Country 
 you want to set and 
press  OK 
 button (* only for EU countries).
- Next, active antenna mode selection OSD will 
appear on the screen.Use “
” or “” to set and 
press OK to continue.See the section, “Initial 
Settings” for more information.
After active antenna mode option is selected, a 
message asking for automatic search appears 
on the screen: 
   
  Press the  OK 
 button to start installation. After 
search is completed for digital channels, a 
message asking whether to search for analogue 
channels appears on the screen: 
 
 
  Press the  OK 
 button to search for analogue 
channels. The following menu appears on the 
screen for analogue channel search:  
 
  Select your  Country 
,  Language 
 and  TXT 
Language 
 by using “
” or “” and “” or “” 
buttons. Press  OK 
 or  RED 
 button to continue. To 
cancel, press  BLUE 
 button. The following menu 
will be displayed during the automatic tuning: 
 
 
  After APS  is fi nalized, the programme table 
will appear on the screen. In the programme 
table you will see the programme numbers and 
names assigned to the programmes.
If you do not accept the locations and/or the 
programme names, you can change them via 
the program table. 
   
Media Browser 
 
• To display Media Browser window, press 
either “ M 
” button on the remote control and 
then select Media Browser by pressing “
” 
or “
” button. Press  OK 
 button to continue. 
Media Browser menu contents (depending 
on the contents of your USB drive) will be 
displayed. 
• Also, when you plug a USB device, the 
following screen will be displayed:
Select YES by pressing “” or “” button 
and press OK button. Media browser will be 
displayed.
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   31MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3115.04.2009   18:56:5115.04.2009   18:56:51 
						

							English   - 32 -
  
  • You can play music, picture and video fi les 
from a USB memory stick. 
  Note 
: If you plug USB stick while in analogue mode, 
the TV will automatically switch to digital TV mode.
   
Note 
: Some USB compliant devices may not be 
supported.
  Note 
: If the USB stick is not recognized after power 
off/on or First Time Installation, fi rst, plug the USB  
device out and power off/on the TV set. Plug the USB  
device in again. 
  Playing MP3 Files 
  
  Play This (OK button) : Plays the selected fi le.
Play (Green button) : Plays all media fi les in the 
folder starting with the selected one.
Pause (Yellow button) : Pause playing fi le.
Stop (Red button) : Stop the playing fi le.
Previous/Next (Left/Right buttons) : Jumps to 
previous or next fi le to play.
Shuffl e (INFO button) : Plays the fi les randomly. 
If shuffle mode is enabled, previous/next 
function will also jump to the tracks randomly.
Loop (Blue button) : Plays the selected fi le 
repeatedly. 
  Viewing JPG Files 
  
  Jump (Numeric buttons) : jump to selected fi le 
using the numeric buttons.
OK : views the selected picture in full screen.
Play / Slideshow (Green button) : starts the 
slideshow with all pictures in the folder. 
  Slideshow Options 
  
  Pause (Yellow button) : Pause the slideshow.
Continue (Green button) : Continue with the 
slideshow.
Previous/Next (Left/Right buttons) : Jump to 
previous or next fi le of slideshow.
Rotate (Up/Down buttons) : Rotate the picture 
using up/down buttons.
EXIT : Back to fi le list.
Shuffl e (Red button) : Shows the fi les randomly 
and continuous in current folder and 
 icon 
turns the highlighted icon. If during a slideshow 
the shuffl e mode is enabled, the next pictures 
will be choosen randomly (If the loop function is 
not enabled, the slideshow will stop at the end. If 
the loop function is enabled, after the slideshow 
ends, it will start again and again).
Loop : Slideshow goes on continuously and  
 icon turns the highlighted icon.
Info : Activates the operations bar.  
 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   32MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3215.04.2009   18:56:5215.04.2009   18:56:52 
						

							English   - 33 -
Video Playback
Play (Red button) : Starts the video 
playback.
Stop (Blue button) : Stops the video 
playback.
Pause (OK button) : Pause the video 
playback.
Rewind (Cursor Left) : Goes backward.
Forward (Cursor Right) : Goes forward.
Menu (Menu button) : Sets subtitle/Audio.
• You can set subtitles by using OK button before 
starting the playback or by using MENU button 
during the playback.
Note: 
-Selected subtitles may not be displayed correctly in 
some cases. 
-In order to display DivX subtitles correctly, you should 
set a “DivX Subtitle” language. See the section, “Divx 
Subtitle” in “Language Settings” for selecting Divx 
Subtitle language.
Press EXIT button to switch back to previous 
menu.
Note: PIP/PAP mode is not available while in 
Media Browser mode.
   
Navigating the Analogue TV 
Menu System 
 
M
INFOOKSELECT
For displaying 
menu options
To confirm choices For navigation
 
  • Press “ M 
” to display the main menu.
• Press “
” or “” button to select an icon. 
• Use “
” or “” button to highlight.
• Press “
” or “” buttons to change the 
settings.
• Press “
” for more options.
• Press  OK 
 to store.
• To exit the menu or return from sub-menu 
screen, press “ M ”. 
 
 
Note 
: These explanations are valid for the navigation 
of the analogue TV menu system. To select options 
that are explained in the following parts, refer to 
“Navigating the Analogue TV Menu System”.  
 
 
Analogue TV Menu System 
 
 
Picture Menu 
  
  Mode 
  For your viewing requirements, you can set the 
related mode option.
Press “
” or “” button to select  Mode 
. Press 
“
” or “” button to choose from one of these 
options:   
 
Cinema 
,   
  Dynamic 
 and  Natural 
.  
   
 
 
 
Brightness/Contrast/Colour/Sharpness/
Hue 
  Press “
” or “” button to select the desired 
option. Press “
” or “” button to set the level. 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   33MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3315.04.2009   18:56:5215.04.2009   18:56:52 
						

							English   - 34 -
 
 
Note 
:  Hue 
 option can only be visible when the TV 
receives an NTSC signal. 
  Colour Temp 
  Press “
” or “” button to select  Colour Temp 
. 
Press “
” or “” to choose from one of these 
options:  Cool ,  Normal  and  Warm . 
 
 
Note 
: 
• Setting  Cool 
 option gives white colours a slight 
blue stress.
• Setting  Warm 
 option gives white colours a slight 
red stress.
• For normal colours, select  Normal 
 option. 
 
Noise Reduction 
  If the broadcast signal is weak and the picture 
is noisy, use  Noise Reduction 
 setting to reduce 
the noise amount. 
  Press “
” or “” button to select  Noise 
Reduction. 
 Press “
” or “” to choose from one 
of these options:  Low 
,  Medium 
,  High 
 or  Off 
. 
  Film Mode 
  Films are recorded at a different number 
of frames per second to normal television 
programmes. 
  Press “
” or “” button to select  Film Mode .
Press “
” or “” button to set this feature On 
or Off. 
Turn this feature on when you are watching.
fi lms to see the fast motion scenes clearly. 
  Game Mode 
  Select  Game Mode 
 by pressing “
” or “
” button. Use “” or “” button to set Game 
Mode as  On 
 or  Off 
. When Game Mode is set 
to On, specific game mode settings, which 
are optimized for better video quality, will be 
loaded.
Also; Picture Mode, Contrast, Brightness, 
Sharpness, Colour and Colour Temp settings 
will be invisible and disabled while Game Mode 
is on. 
   
Note 
:
Picture mode selection button on the remote control 
will have no function while Game Mode is on.
If the TV is switched to PIP/PAP mode, Game Mode 
setting will be disabled and be removed from the 
Picture menu. 
  Picture Zoom 
  Select  Picture Zoom 
 by pressing “
” or “
” button.
Use “
” or “” buttons, to change picture zoom  
to  Auto 
,  16:9 
,  4:3 
,  Panoramic 
,  14:9 
,  Cinema 
, 
  Subtitle 
 or  Zoom 
. 
  Reset 
  Press “
” or “” button to select  Reset 
. Press 
“
” or “” or  OK 
 button to reset the picture 
modes to factory default settings. 
  Store 
  Press “
” or “” button to select Store. Press “
” or  OK 
 button to store the settings. “ Stored... 
” 
will be displayed on the screen.  
 
 
 
 
Sound Menu 
  
  Volume 
  Press “
” or “” button to select  Volume 
. 
Press “
” or “” button to change the level of 
the Volume. 
  Equalizer 
  Press “
” or “” button to select  Equalizer 
. 
Press “
” button to view equalizer menu. 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   34MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3415.04.2009   18:56:5315.04.2009   18:56:53 
						

							English   - 35 -
  
  Press “
” or “” button to change the preset. 
In equalizer menu, the preset can be changed 
to  Music 
,  Movie 
,  Speech 
,  Flat 
,  Classic 
 and 
  User 
. 
  Select the desired frequency by pressing “
” or “” button and increase or decrease the 
frequency gain by pressing “
” or “” button. 
  Press the “ M 
” button to return to the previous 
menu. 
   
Note 
: Equalizer menu settings can be changed only 
when the  Equalizer 
  Mode 
 is in  User 
. 
 
Balance 
  This setting is used for emphasizing left or right 
speaker balance.
Press “
” or “” button to select Balance. 
Press “
” or “” button to change the level of 
the balance. Balance level can be adjusted 
between -32 and + 32. 
  Headphone 
  Press “
” or “” button to select  Headphone 
. 
Press “
” button to view the headphone 
menu.
Headphone sub-menu options are described 
below: 
  Volume 
  Press “
” or “” button to select  Volume 
. Press  
 
“
” button to increase headphone volume 
level. Press “
” button to decrease headphone 
volume level. Headphone volume level can be 
adjusted between 0 and 63 .  Store
Press “
” or “” button to select Store. Press “
” or  OK 
 button to store the settings. “ Stored... 
” 
will be displayed on the screen  
. 
  Sound Mode 
  Press “
” or “” button to select  Sound Mode . 
Using “
” or “” button, you can select Mono, 
Stereo, Dual I or Dual II mode, only if the 
selected channel supports that mode. 
  AV L  
  Automatic Volume Limiting (AVL) function 
adjusts the sound to obtain fi xed output level 
between programmes (For instance, volume 
level of advertisements tend to be louder than 
programmes).
Press “
” or “” button to select  AV L 
. Press “” 
or “
” button  to set the AVL as  On 
 or  Off 
. 
  Spdif Out 
  Press “
” or “” button to select  Spdif Out 
. 
Press “
” or “” button to set the  Spdif Out 
.  
as  On 
 or  Off 
. 
 
 
Note 
: If Spdif Out is set to On, headphone will be 
disabled. 
    
 
 
  
 
 
 
Effect 
If you are watching a mono broadcast, set Effect 
on to obtain a better sound effect which will be 
more stereo-like. If the current sound system is 
stereo, switching this effect on will give a more 
spatial effect.
Press “
” or “” button to select Effect. Press  
“
” or “” button  to set as On or Off . 
 
 
  Store 
  Press “
” or “” button to select Store. Press “
” or  OK 
 button to store the settings. “ Stored... 
” 
will be displayed on the screen. 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   35MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3515.04.2009   18:56:5415.04.2009   18:56:54 
						

							English   - 36 -
 
 
 
Feature Menu 
  
  Pip-Pap 
  In the  Feature 
 menu, highlight  PIP 
 item by 
pressing “
” or “” buttons. Press “” button 
to enter  PIP 
 submenu: 
 
 
  Using “
” or “” button, you can switch to PIP, 
PAP mode or turn off the feature.
If the TV is switched to PIP or PAP mode, 
Pip-Pap submenu will change accordingly and 
the following settings will appear on the same 
menu screen.   
 
Note that if you switch to PAP mode by using Pip-Pap 
setting, only Source and Swap options will be active 
among the menu settings. 
  Pip-Pap 
  This line controls Pip/Pap modes. Use “
” or “” 
buttons to switch the TV to  Pip 
,  Pap 
 or  Off 
.  
  Pip Size 
  Using this setting, you can set the size of the 
Pip window. Press “
” or “” button to highlight Pip Size item. Use “
” or “” button to set Pip 
Size to Small or Large. 
   
Note 
: This setting will be inactive if the TV is set to 
Pap mode. 
  PIP Position 
  This setting is used for moving the sub 
picture.
Select PIP Position  item by using “
” or 
“
” button. Use “” or “” button to adjust  PIP 
position. 
Positions available are: Bottom Right,Bottom 
Left, Top Left and Top Right. 
  Source 
  PIP Source setting enables you to select the 
source of the sub picture.
Select PIP Source item by using “
” or “
” button. Use “” or “” button to set  PIP  
source. 
  Program 
  This setting will be unavailable to be used. 
  Swap 
  Select Swap item by using “
” or “” button. 
Use “
” or “” button to set. This function 
enables to swap between the main and the 
PIP picture. 
   
Note 
: See Appendix E for all PIP/PAP modes. 
 
Sleep Timer 
  Press “
” or “” button to select  
Sleep Timer . 
Use “
” or “” button to set the  Sleep Timer. 
The timer can be programmed between  Off 
 and 
  120 
 minutes in steps of  10 
 minutes. 
If  Sleep Timer 
 is activated, at the end of the 
selected time, the TV goes automatically to 
standby mode. 
  Child Lock 
  Press “
” or “” button to select  Child Lock 
.
Use “
” or “” button  to set the Child Lock  On 
 
or  Off 
. When On is selected, the TV can only 
be controlled by the remote control handset. In 
this case the control panel buttons (except for 
the  STANDBY 
 button) will not work.
Hence, if one of those buttons is pressed,  Child 
Lock On 
 will be displayed on the screen when 
the  menu screen is not visible. 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   36MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3615.04.2009   18:56:5415.04.2009   18:56:54 
						

							English   - 37 -
 
Language 
  Press “
” or “” button to select  Language 
. 
Use “
” or “” button to select the  Language 
.  
  Default Zoom 
  While zoom mode is set as  AUTO , the TV will 
set the zoom mode in accordance with the  
signal of the broadcast. If there is no WSS or 
aspect ratio information, the TV will then use this 
setting to adopt. Press “
” or “” button to select 
  Default Zoom 
. You can set  Default Zoom 
 to 
  Panoramic 
,  16:9 
,  4:3 
 or  14:9 
 by pressing “
” or “” button. 
  Blue Background 
  If the signal is weak or absent, the TV will 
automatically change to a blue screen. To 
enable this, set  Blue Background 
 to  On 
.
By pressing “
” or “” button, select  Blue 
Background 
. Press “
” or “” button  to set 
  Blue Background 
 as  On 
 or  Off 
. 
  Menu Background 
  Press “
” or “” button to select  Menu 
Background 
. You can set menu background 
level by pressing “
” or “” button. 
  Backlight 
  This setting controls the backlight level. Select 
  Backlight  by pressing “
” or “” button. Press“
” or “” button to set  Backlight  to  Auto, 
Medium ,  Maximum  or  Minimum . 
  Menu Timeout 
  To set a specific display timeout for menu 
screens, set a value for this option.
Press “
” or “” button to select  Menu Timeout . 
Use “
” or “” button to change menu timeout 
to  15 sec 
,  30 sec 
 or  60 sec 
. 
  Teletext Language 
  Press “
” or “” button to select  Teletext 
Language 
. Use “
” or “” button to change 
  Teletext Language 
 to  West, East 
,  Turk/Gre , 
Cyrillic, Arabic or Persian 
 
 
 
 
.
 
 
 
 
HDMI PC Full Mode
If you want to view PC screen in HDMI mode 
by using external connection, HDMI PC FULL 
MODE option should be On to adjust the screen 
ratio correctly. This item might be inactive in 
some resolutions.Ext Out 
  Press “
” or “” button to select Ext Out. Use “
” or “” button to set the Ext Out as On or Off. 
 
 
Note :
For copying from a DVD or VCR device, you should 
choose desired source from source menu and turn 
“On” to EXT Out from feature menu. 
Note : If you do not want Tuner video out put from 
Scart 1 or Scart 2, please set the Ext Out as Off , 
otherwise you can set it as On.
   
Install Menu 
  
  Program 
  Press “
” or “” button to select Program. Use  
“
” or “” button to select the program number. 
You can also enter a number using the numeric 
buttons on the remote control. There are 200 
programme storage between 0 and 199. 
  Band 
  Band can be selected either C or S. Press “
” 
or “
” button to set Band.  
  Channel 
  Channel can be changed by “
” or “” button 
or numeric buttons. 
  Colour System 
  Press “
” or “”  button to select Colour System. 
Use “
” or “” button to change the colour 
system to PAL, PAL 60, SECAM or AUTO. 
  Sound System 
  Press “
” or “” button to select  Sound System.  
Press “
” or “” button to change the sound 
system to BG,DK, I, L or L’. 
  Fine Tune 
  Press “
” or “” button to select Fine Tune. 
Press “
” or “” button to adjust the tuning. 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   37MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3715.04.2009   18:56:5515.04.2009   18:56:55 
						

							English   - 38 -
 
Search 
  Press “
” or “” button to select Search. Use  “
” or “” button to start programme searching. 
You can also enter the desired frequency 
using the numeric buttons while Search item 
is highlighted. 
  Store 
  Press “
” or “” button to select Store. Press “
” or  OK 
 button to store the settings. “ Stored... ” 
will be displayed on the screen. 
  Install Menu in AV Modes 
  The following screen appears in the install menu 
when the TV is in AV modes. Note that limited 
options will be available. Switch to TV mode for 
viewing complete version of the  Install  menu. 
 
 
  Colour System 
  Press “
” or “” button to select  Colour 
System 
. Use “
” or “” button to change the 
colour system to  PAL, SECAM, PAL60, AUTO, 
NTSC 4,43 or NTSC 3,58. 
 
  Store 
  Press “
” or “” button to select  Store 
Program 
. Press “
” or  OK 
 button to store the 
settings. “ Stored... 
” will be displayed on the 
screen. 
  Program Table 
  Select  Program Table 
 by pressing “
” or “
” button.  
 
  By moving the cursor in four directions you can 
reach 20 programmes in the same page. You 
can scroll the pages up or down by pressing the 
navigation buttons to see all the programmes 
in TV mode (except for the AV modes). By 
cursor action, programme selection is done 
automatically. 
  Name 
  To change the name of a programme, select the 
programme and press the  RED 
 button.
The fi rst letter of the selected name will be 
highlighted. Press “
” or “” button to change 
that letter and “
” or “” button to select the 
other letters.  By pressing the  RED 
 button, you 
can store the name. 
  Move 
  Select the programme which you want to insert 
by navigation buttons. Press the  GREEN 
 
button. By navigation buttons move the selected 
programme to the decided programme space 
and press the  GREEN 
 button again. 
  Delete 
  To delete a programme, press the  YELLOW 
 
button. Pressing the  YELLOW 
 button again 
erases the selected programme from the 
programme list, and the following programmes 
shift one line up. 
  APS (Auto Programming System) 
  When you press the  BLUE 
 button for starting 
automatic tuning,  
Auto Programming System 
 
 
menu will appear on the screen: 
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   38MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3815.04.2009   18:56:5615.04.2009   18:56:56 
						

							English   - 39 -
  
  Country 
  Press “
” or “” button to select your country. 
If you want to exit from A.P.S. function, press 
the  BLUE 
 button.
When you press   OK 
 or  RED 
 button for starting 
automatic tuning, all stored programmes will 
be erased and the TV will search for available 
channels. During the search, the following OSD 
will be displayed: 
 
 
  Whenever you press the  BLUE 
 button, APS  
function stops and  Program Table  appears on 
the screen.
If you wait until the end of  APS, Program Table  
will be displayed with the programmes found 
and located.  
 
 
Source Menu 
 
Press “” or “” button and select the sixth icon. 
Then press “
” or  OK 
 button. Source menu 
appears on the screen:  
 
  In source menu, highlight a source by pressing 
“
” or “” button and switch to that mode 
by pressing “
” button. Source options are; 
  TV 
,  DTV/USB 
,  EXT-1 
,  EXT-2 
, EXT-2S,  FAV 
, 
  HDMI-1 
,  HDMI-2 
,  
  
YPbPr 
 or  PC-VGA 
. 
 
 
Note 
: Once you have connected optional equipment 
systems to your TV, you should select the required 
input to view pictures from that source.  
MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   39MB35_[GB]_SSM_32890W_1050UK_UKIDTV_BRONZE3_10062394_50146336.indd   3915.04.2009   18:56:5615.04.2009   18:56:56