Samsung UE 55C7000 User Manual

							21English
03 Basic Features 
■ 3D Auto View (Off / On): If 3D Auto View is set to On, 
a “Side-By-Side” format HDMI signal with one of the 
resolutions below is automatically switched to 3D. Here, 
correct 3D information must be sent from the HDMI 1.3 
transmitter.
 
✎If a 3D failure occurs due to a 3D information error, 
set  3D Auto View  to Off and manually select a 
3D Mode  using the  3D button or corresponding 
menu

.
 
✎Support resolution (16:9 only)
Resolution Frequency (Hz)
1280 x 720p 60 Hz
1920 x 1080i 60 Hz
1920 x 1080p 24 / 30 / 60 Hz
Resolution supported for HDMI PC mode
The resolution for HDMI PC mode is optimized to 1920 x 
1080 input.
An input resolution other than 1920 x 1080 may not be 
displayed properly in 3D display or full screen mode.
How to watch the 3D image
1.  Press the CONTENT button, then the Content V iew 
menu will appear.
2.  Press the  or  button, then select 3D.
To watch in 3D, wear 3D Active Glasses and press the 
power button on the glasses.
3.  Select OK, then press the ENTER
E button.
4.  Using the  or  buttons on your remote control, select 
the 3D Mode of the image you want to view.
 
✎Some 3D modes may not be available depending 
on the format of the image source.
Supported formats and operating specifications for 
HDMI 1.4
Source signal format Standard HDMI 1.4 3D
1920x1080p@24Hz x 2 1920x2205p@24Hz
1280x720p@60Hz x 2 1280x1470p@60Hz
1280x720p@50Hz x 2 1280x1470p@50Hz
The mode is automatically switched to 3D in one of the 
source signal formats above.
For the HDMI 1.4@24Hz format, the TV is optimized as 
follows:
 –Resolution First Display Mode: If Auto Motion Plus 
is set to Off, Clear or Standard, you can watch the 
video at a high resolution optimized to the resolution 
of the source video.
 – Judder Reduction Display Mode: When Auto 
Motion Plus is set to Smooth or Custom, you can 
watch a smooth picture without judder.
Before using 3D function...
 
✎NOTE
 
You may notice a small amount of screen flickering 
when watching 3D images in poor light conditions 
(from a strobe light, etc.), or under a fluorescent lamp 
(50Hz ~ 60Hz) or 3 wavelength lamp. If so, dim the 
light or turn the lamp off.
 
3D mode is automatically disabled in following cases: 
when changing a channel or the input source, or 
accessing  Media Play  or Internet@TV .
 
Some Picture functions are disabled in  3D mode.
 
PIP is not supported in  3D mode.
 
Auto Program  is disabled in 3D  mode.
 
3D Active Glasses from other manufacturers may not 
be supported.
 
When the T V is initially powered on, may take some 
time until the 3D display is optimized.
3D
OK
To watch in 3D, wear 3D glasses and 
press the power button on the glasses.
Watching 3D picture for a long time may 
cause eye fatigue and/or dizziness.
Cancel
U Move    E Enter    e Exit
3D3D
[ 	\ 	>,;	]	 =*,;	]	/=*
						

							22English
Basic Features
 
If there is any other 3D product, electronic 
devices such as a PDP or LCD T V, or wireless 
communication devices nearby, the 3D Active 
Glasses may not work properly due to mutual 
interference. If there is a problem, keep other 
electronic devices as far away as possible from the 
3D Active Glasses.
 
Photos  of Media Play  are shown in “2D  3D” 
mode only.
 
If lying on your side, the 3D-effects may not be 
displayed. 
 
Be sure to stay within the viewing angle and optimum 
TV viewing distance when watching 3D pictures.
 – Otherwise, you may not be able to enjoy proper 3D  effects.
Picture Reset (OK / Cancel)
Resets your current picture mode to its default settings.
 
¦ Setting up the TV with Your PC
Set the input source to PC.
 
OMENUm  Picture  ENTERE
Auto Adjustment t
Adjust frequency values/positions and fine tune the settings 
automatically. 
 
✎Not available when connecting with an HDMI/DVI cable.
Screen
 
■ Coarse / Fine: Removes or reduces picture noise. If the 
noise is not removed by Fine-tuning alone, then adjust 
the frequency as best as possible (Coarse) and Fine-
tune again. After the noise has been reduced, readjust 
the picture so that it is aligned to the center of screen.
 
■ Position: Adjust the PC’s screen positioning if it does 
not fit the TV screen. Press the  or  button to adjust 
the Vertical-Position. Press the  or  button to adjust 
the Horizontal-Position.
 
■ Image Reset: Resets the image to default settings.
Using Your TV as a Computer (PC) Display
Setting Up Your PC Software (Based on Windows XP)
Depending on the version of Windows and the video card, 
the actual screens on your PC will probably look different, but 
the same basic set-up information will apply in most cases. 
(If not, contact your computer manufacturer or Samsung 
Dealer.)
1.  Click on “Control Panel” on the Windows start menu.
2.  Click on “Appearance and Themes” in the “Control 
Panel” window and a display dialog-box will appear.
3.  Click on “Display” and a display dialog box will appear.
4.  Navigate to the “Settings” tab on the display dialog-box.
 
 The correct size setting (resolution) [Optimum: 1920 X 
1080 pixels]
 
 If a vertical-frequency option exists on your display 
settings dialog box, the correct value is “60” or “60 Hz”. 
Otherwise, just click “OK” and exit the dialog box.
Sound Menu
 
¦ Changing the Preset Sound Mode
 
OMENUm  Sound  SRS TheaterSound  
ENTER
E
SRS TheaterSound t 
 
■ Standard: Selects the normal sound mode.
 
■ Music: Emphasizes music over voices.
 
■ Movie: Provides the best sound for movies.
 
■ Clear Voice: Emphasizes voices over other sounds.
 
■ Amplify: Increase the intensity of high-frequency sound 
to allow a better listening experience for the hearing 
impaired.
 
¦ Adjusting Sound Settings
 
OMENUm  Sound  Equalizer  ENTERE
Equalizer
Adjusts the sound mode (standard sound mode only).
 
■ Balance L/R: Adjusts the balance between the right and 
left speaker.
 
■ 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth 
Adjustment): Adjusts the level of specific bandwidth 
frequencies.
 
■ Reset: Resets the equalizer to its default settings.
 
						

							23English
03 Basic Features 
¦ Sound Settings
 
OMENUm  Sound  ENTERE
SRS TruSurround HD (Off / On) t
(standard sound mode only)
This function provides a virtual 5.1 channel surround sound 
experience through a pair of speakers using HRTF (Head 
Related Transfer Function) technology.
SRS TruDialog (Off / On) 
(standard sound mode only)
This function allows you to increase the intensity of a voice 
over background music or sound effects so that dialog can 
be heard more clearly.
Preferred Language
(digital channels only)
Digital-TV broadcasts are capable of simultaneous 
transmission of many audio tracks (for example, 
simultaneous translations of the program into foreign 
languages).
 
✎You can only select a language among the ones being 
broadcasted.
Multi-Track Sound (MTS) t
(analog channels only)
 
■ Mono: Choose for channels that are broadcasting in 
mono or if you are having difficulty receiving a stereo 
signal.
 
■ Stereo: Choose for channels that are broadcasting in 
stereo.
 
■ SAP: Choose to listen to the Separate Audio Program, 
which is usually a foreign-language translation.
 
✎Depending on the particular program being broadcast, 
you can listen to Mono, Stereo  or SAP. 
Auto Volume (Off / Normal / Night)
To equalize the volume level on each channel, set to Normal.
 
■ Night: This mode provides an improved sound 
experience compared to Normal mode, making almost 
no noise. It is useful at night.
Speaker Select (External Speaker / TV 
Speaker)
A sound echo may occur due to a difference in decoding 
speed between the main speaker and the audio receiver. In 
this case, set the TV to External Speaker.
 
✎When  Speaker Select  is set to External Speaker , the 
volume and MUTE  buttons will not operate and the 
s

ound settings will be limited. 
 
✎When  Speaker Select  is set to External Speaker .
 
T V Speaker: Off, External Speaker: On
 
✎When  Speaker Select  is set to TV Speaker .
 
TV Speaker: On, External Speaker: On
 
✎If there is no video signal, both speakers will be mute.
SPDIF Output
SPDIF (Sony Philips Digital Interface) is used to provide digital 
sound, reducing interference going to speakers and various 
digital devices such as an A/V Receiver/Home theater.
 
■ Audio Format: During the reception of a digital TV 
broadcast, you can select the Digital Audio output 
(SPDIF) format from the options PCM or Dolby Digital.
 
■ Audio Delay: Correct audio-video sync problems, when 
watching TV or video, and when listening to digital audio 
output using an external device such as an AV receiver 
(0ms ~ 250ms).
Sound Reset (OK / Cancel)
Reset all sound settings to the factory defaults.
 
						

							24English
Basic Features
Setup Menu
 
¦ Setting the Time
 
OMENUm  Setup  Time  ENTERE
Time
 
■ Clock: Setting the clock is for using various timer 
features of the TV.
 
OThe current time will appear every time you press 
the INFO button.
 
✎If you disconnect the power cord, you have to set 
the clock again.
Clock Mode (Auto / Manual)  – Auto: Set the current time automatically using the 
time from a digital channel.
 
✎The antenna must be connected in order to set 
the time automatically.
 – Manual: Set the current time manually.
 
✎Depending on the broadcast station and signal, 
the auto time set up may not be correct. In this 
case, set the time manually.
Clock Set: Set the Month, Day, Year, Hour, Minute and 
am/pm manually.
 
✎Available only when  Clock Mode is set to 
Manual .
 
✎You can set the Month , Day, Ye a r , Hour  and 
Minute  directly by pressing the number buttons 
on the remote control.
DST (Daylight Saving Time) (Off / On): Switches the 
Daylight Saving Time function on or off.
 
✎This function is only available when the  Clock 
Mode  is set to Auto .
Time Zone: Select your time zone.
 
✎This function is only available when the  Clock 
Mode  is set to Auto .
 
¦ Using the Sleep Timer
 
OMENUm  Setup  Time  Sleep Timer  
ENTER
E
 
■ Sleep Timer t : Automatically shuts off the TV 
after a preset period of time. (30, 60, 90, 120, 150 and 
180 minutes).
 
✎To cancel the  Sleep Timer, select Off.
 
¦ Setting the On / Off Timer
 
OMENUm  Setup  Time  Timer 1  
ENTER
E
You can set the TV to turn on automatically at a preset time.
 
■ Timer 1 / Timer 2 / Timer 3: Three different on / off 
timer settings can be made. You must set the clock first.
On Time / Off Time: Set the hour, minute, and activate 
/ inactivate. (To activate the timer with the setting you’ve 
chosen, set to Activate.)
Volume: Set the desired volume level.
Source: Select TV or USB content to be played when 
the TV is turned on automatically. (USB can be selected 
only when a USB device is connected to the TV)
Antenna (when the Source is set to TV): Select Air or 
Cable.
Channel (when the Source is set to TV): Select the 
desired channel.
Contents (when the Source is set to USB): Select a 
folder in the USB device containing music or photo files 
to be played when the TV is turned on automatically.
 
✎NOTE
 
If there is no music file on the USB device or the 
folder containing a music file is not selected, the 
Timer function does not operate correctly.
 
When there is only one photo file in the USB, 
the Slide Show will not play.
 
If a folder name is too long, the folder cannot be 
selected.
 
Each USB you use is assigned its own folder. 
When using more than one of the same type of 
USB, make sure the folders assigned to each 
USB have different names.
10 TVCable 1
0000am
00 00am▲
▼
Timer 1
On Time
Off Time
Volume Inactivate
Inactivate
Sun Mon Tue Wed Thu Fri SatOnce Source
AntennaChannel
Repeat
L Move    U Adjust    E Enter    R Return
 
						

							25English
03 Basic FeaturesRepeat: Select Once, Everyday, Mon~Fri, Mon~Sat, 
Sat~Sun or Manual to set at you convenience. If you 
select Manual, you can set up the day you want to 
activate the timer.
 
✎The c mark indicates the day is selected.
 
✎Auto Power Off (available only when the T V is turned 
on by the Timer): The T V will be automatically turned off 
after 3 hours of being left idle to prevent overheating.
 
¦ Locking Programs
 
OMENUm  Setup  Security  ENTERE
Security
The PIN input screen appears, Enter your 4 digit PIN number.
 
■ V-Chip: The V-Chip feature automatically locks out 
programs that are deemed inappropriate for children. 
The user must enter a PIN (personal identification 
number) before any of the V-Chip restrictions are set up 
or changed.
 
✎NOTE
 
V-Chip  is not available in  HDMI, Component  
or  PC  mode.
 
The default PIN number of a new T V set is 
“0-0-0-0”.
 
Allow All : Press to unlock all T V ratings. 
 
Block All : Press to lock all T V ratings.
V-Chip Lock (Off / On): You can block rated TV 
Programs.
TV Parental Guidelines: You can block TV programs 
depending on their rating. This function allows you to 
control what your children are watching.  – TV-Y: Young children / TV-Y7: Children 7 and over / 
TV-G: General audience / TV-PG: Parental guidance 
/ TV-14: Viewers 14 and over / TV-MA: Mature 
audience
 – ALL: Lock all TV ratings. / FV: Fantasy violence / V: 
Violence / S: Sexual situation / L: Adult Language / D: 
Sexually Suggestive Dialog
 
✎The  V-Chip  will automatically block certain 
categories dealing with more sensitive material. 
For example, if you block the TV-Y  category, 
then  TV-Y7  will automatically be blocked. 
Similarly, if you block the TV-G  category, then 
all the categories in the young adult group will 
be blocked ( TV-G, TV-PG, TV-14  and TV-MA). 
The sub-ratings ( D, L, S, V) work similarly. So, 
if you block the  L sub-rating in TV-PG, then 
the  L sub-ratings in  TV-14 and TV-MA  will 
automatically be blocked. MPAA Rating: You can block movies depending on 
their MPAA rating. The Motion Picture Association of 
America(MPAA) has implemented a rating system that 
provides parents or guardians with advanced information 
on which films are appropriate for children.
 – G: General audience (no restrictions). / PG: Parental 
guidance suggested. / PG-13: Parents strongly 
cautioned. / R: Restricted. Children under 17 should 
be accompanied by an adult. / NC-17: No children 
under age 17. / X: Adults only. / NR: Not rated.
 
✎The  V-Chip  will automatically block any 
category that deals with more sensitive material. 
For example, if you block the PG-13  category, 
then  R, NC-17  and X will automatically be 
blocked.
Canadian English: You can block TV programs 
depending on their Anglophone Canadian ratings.  – C: Programming intended for children under age 8. / 
C8+: Programming generally considered acceptable 
for children 8 years and over to watch on their own. 
/ G: General programming, suitable for all audiences. 
/ PG: Parental Guidance. / 14+: Programming 
contains themes or content which may not be 
suitable for viewers under the age of 14. / 18+: Adult 
programming.
 
✎The  V-Chip  will automatically block any 
category that deals with more sensitive material. 
For example, if you block the G category, then 
PG, 14+ and 18 +  will automatically be blocked.
Canadian French: You can block TV programs 
depending on their French Canadian rating.  – G: General / 8 ans+: Programming generally 
considered acceptable for children 8 years and over 
to watch on their own. / 13 ans+: Programming may 
not be suitable for children under the age of 13. / 16 
ans+: Programming is not suitable for children under 
the age of 16. / 18 ans+: Programming restricted to 
adults.
 
✎The  V-Chip  will automatically block any 
category that deals with more sensitive material. 
For example, if you block the 8 ans+ category, 
then  13 ans+, 16 ans+ and 18 a n s +  will 
automatically be blocked also.
Downloadable U.S. Rating: Parental restriction 
information can be used while watching DTV channels.
 
						

							26English
Basic Features
 
✎NOTE
 
If information is not downloaded from the 
broadcasting station, the  Downloadable U.S. 
Rating  menu is deactivated.
 
Parental restriction information is automatically 
downloaded while watching DT V channels. It 
may take several seconds.
 
The  Downloadable U.S. Rating  menu 
is available for use after information is 
downloaded from the broadcasting station. 
However, depending on the information from 
the broadcasting station, it may not be available 
for use.
 
Parental restriction levels differ depending on 
the broadcasting station. The default menu 
name and Downloadable US Rating  change 
depending on the downloaded information.
 
Even if you set the on-screen display to another 
language, the Downloadable U.S. Rating  
menu will appear in English only.
 
The rating will automatically block certain 
categories that deal with more sensitive 
material.
 
The rating titles (For example: Humor Level..etc) 
and TV ratings (For example: DH, MH, H..etc) 
may differ depending on the broadcasting 
station.
 
■ Change PIN: The Change PIN screen will appear. 
Choose any 4 digits for your PIN and enter them. As 
soon as the 4 digits are entered, the Confirm New 
PIN screen appears. Re-enter the same 4 digits. When 
the Confirm screen disappears, your PIN has been 
memorized.
How to watch a restricted channel
If the TV is tuned to a restricted channel, the V-Chip will 
block it. The screen will go blank and the following message 
will appear:
This channel is blocked by V-Chip. Please enter the PIN to 
unblock.
 
✎If you forget the PIN, press the remote-control buttons 
in the following sequence, which resets the pin to “0-0-
0-0:”  POWER  (off)  MUTE   8  2  4  POWER  
(o

n)
 
¦ Other Features
 
OMENUm  Setup  ENTERE
Menu Language
Set the menu language.
1.  Select Menu Language and press the ENTER
E 
button.
2.  Choose desired language and press the ENTER
E 
button.
 
✎Choose between  English, Español  and Français .
Caption
(On-Screen Text Messages)
 
■ Caption (Off / On): You can switch the 
caption function on or off. If captions are 
not available, they will not be displayed on 
the screen.
 
✎The Caption feature doesn’t work in 
Component, HDMI or PC modes.
 
■ Caption Mode: You can select the desired 
caption mode.
 
✎The availability of captions depends on the 
program being broadcast.
Default / CC1~CC4 / Text1~Text4: (analog channels 
only) The Analog Caption function operates in either 
analog TV channel mode or when a signal is supplied 
from an external device to the TV. (Depending on the 
broadcasting signal, the Analog Caption function may or 
may not work with digital channels.)
Default / Service1~Service6 / CC1~CC4 / 
Text1~Text4: (digital channels only) The Digital Captions 
function works with digital channels.
 
✎Service1~6  may not be available in digital caption 
mode depending on the broadcast.
CC
 
						

							27English
03 Basic Features 
■ Digital Caption Options: (digital channels only)
Size: Options include Default, Small, Standard and 
Large. The default is Standard.
Font Style: Options include Default and Styles 0 to 7. 
The default is Style 0.
Foreground Color: Options include Default, White, 
Black, Red, Green, Blue, Yellow, Magenta and Cyan. You 
can change the color of the letter. The default is White.
Background Color: Options include Default, White, 
Black, Red, Green, Blue, Yellow, Magenta and Cyan. 
You can change the background color of the caption. 
The default is Black.
Foreground Opacity: This adjusts the opacity of text. 
Options include Default, Transparent, Translucent, Solid 
and Flashing.
Background Opacity: This adjusts the opacity of 
the caption background. Options include Default, 
Transparent, Translucent, Solid and Flashing.
Return to Default: This option sets each Size, Font 
Style, Foreground Color, Background Color, Foreground 
Opacity and Background Opacity to its default.
 
✎NOTE
 
Digital Caption Options  are available only 
when  Default  and Service1 ~ Service6  can be 
selected in Caption Mode.
 
The availability of captions depends on the 
program being broadcasted.
 
The  Default  setting follows the standards set by 
the broadcaster.
 
The Foreground and Background cannot be set 
to have the same color.
 
You cannot set both the  Foreground Opacity 
and the Background Opacity  to Transparent.
Network (Network Type / Network Setup 
/ Network Test / SWL (Samsung Wireless 
Link) / SWL connect)
For details on set up options, refer to the “Network 
Connection” instructions (p. 30).
General
 
■ Game Mode (Off / On): When connecting to a game 
console such as PlayStation™ or Xbox™, you can enjoy 
a more realistic gaming experience by selecting the 
game menu.
 
✎NOTE
 
Precautions and limitations for game mode
 – To disconnect the game console and connect  another external device, set Game Mode to Off in 
the setup menu.
 – If you display the TV menu in Game Mode, the  screen shakes slightly.
 
Game Mode  is not available when the input source 
is set to T V or PC.
 
After connecting the game console, set  Game Mode 
to  On . Unfortunately, you may notice reduced picture 
quality.
 
If  Game Mode  is On:
 – Picture mode is set to Standard and Sound mode 
is set to Movie.
 – Equalizer is not available.
 
■ BD Wise (Off / On): Provides the optimal picture quality 
for Samsung DVD, Blu-ray and Home Theater products 
which support BD Wise. When BD Wise is turned On, 
the picture mode is automatically changed to the optimal 
resolution.
 
✎Available when connecting Samsung products 
that support BD Wise  through a HDMI cable.
 
■ Menu Transparency (Bright / Dark): Set the 
Transparency of the menu.
 
■ Melody (Off / Low / Medium / High): Set so that a 
melody plays when the TV is turned on or off.
 
✎Melody  is disabled when FastStart  is On.
 
■ FastStart (Off / On): When the TV is powered on, the 
screen will come on quickly with this feature.
 
■ Light Effect (Off / In Standby / Watching TV / 
Always): You can turn the LED on/off on the front of TV. 
Turn it off to save power or if the LED is too bright for 
you.
 
✎Set the Light Effect  to Off to reduce the power 
consumption.
 
✎The color of light may very depending on the 
model.
 
						

							28English
Basic Features
Wireless Remote Control (Off / On)
Turn on/off or give permission to Samsung mobile phones/
devices.
You must have a Samsung Mobile phone/device which 
supports Wireless Remote Control. For more details, refer 
to each device's manual.
 
¦ Picture In Picture (PIP)
PIP t
You can watch the TV tuner and one external video source 
simultaneously. PIP (Picture-in-Picture) does not function in 
the same mode. 
 
OMENUm  Setup  PIP  ENTERE
 
✎NOTE
 
For PIP sound, refer to the  Sound Select 
instructions.
 
If you turn the T V off while watching in PIP mode, the 
PIP window will disappear.
 
You may notice that the picture in the PIP window 
becomes slightly unnatural when you use the main 
screen to view a game or karaoke.
 
While  V-Chip  or Internet@TV  is in operation, the PIP  
function cannot be used.
 
PIP Settings
Main picture Sub picture
Component, HDMI1/DVI, 
HDMI2, HDMI3, HDMI4, 
PC TV
 
■ PIP (Off / On): Activate or deactivate the PIP function.
 
■ Air/Cable (Air / Cable): Select either Air or Cable as the 
input source for the sub-screen.
 
■ Channel: Select the channel for the sub-screen.
 
■ Size (
Õ / à / À / Œ): Select a size for the sub-
picture.
 
■ Position (
à / – / — / œ): Select a position for the 
sub-picture.
 
✎In Double (À, Œ) mode, Position  cannot be 
selected.
 
■ Sound Select (Main / Sub): You can choose the 
desired sound (Main / Sub) in PIP mode.
Support Menu
 
OMENUm  Support  ENTERE
Legal Notice
 
✎The  Legal Notice  may differ depending on the country.
Self Diagnosis
 
✎Self Diagnostic might take few seconds, this is part of 
the normal operation of the T V.
 
■ Picture Test: Use to check for picture problems. 
Ye s : If the test pattern does not appear or there is 
noise in the test pattern, select Yes. There may be a 
problem with the TV. Contact Samsung’s Call Center for 
assistance (1-800-SAMSUNG).
No: If the test pattern is properly displayed, select No. 
There may be a problem with your external equipment. 
Please check your connections. If the problem persists, 
refer to the external device’s user manual.
 
■ Sound Test: Use the built-in melody sound to check for 
sound problems. 
 
✎If you hear no sound from the T V’s speakers, 
before performing the sound test, make sure 
Speaker Select  is set to TV Speaker  in the 
Sound  menu.
 
✎The melody will be heard during the test even if 
Speaker Select  is set to External Speaker  or the 
sound is muted by pressing the  MUTE button.
Ye

s : If you can hear sound only from one speaker or not 
at all during the sound test, select Yes. There may be a 
problem with the TV. Contact Samsung’s Call Center for 
assistance (1-800-SAMSUNG).
No: If you can hear sound from the speakers, select No. 
There may be a problem with your external equipment. 
Please check your connections. If the problem persists, 
refer to the external device’s user manual.
 
■ Signal Information: (digital channels only) An HD 
channel’s reception quality is either perfect or the 
channels are unavailable. Adjust your antenna to 
increase signal strength. 
 
■ Troubleshooting: If the TV seems to have a problem, 
refer to this description.
 
✎If none of these troubleshooting tips apply, contact 
the Samsung customer service center.
 
						

							29English
03 Basic Features
Software Upgrade
Software Upgrade can be performed by network 
connection or downloading the latest firmware from “www.
samsung.com.” to a USB memory device.
Current Version - the software already installed in the TV.
 
✎Software is represented as “Year/Month/Day_Version.”
Installing the Latest Version  
■ By USB: Insert a USB 
drive containing the 
firmware upgrade file, 
downloaded from “www.
samsung.com,” into the 
TV. Please be careful not 
to disconnect the power or 
remove the USB drive until 
upgrades are complete. 
The TV will be turned off 
and on automatically after 
completing the firmware upgrade. When software is 
upgraded, video and audio settings you have made will 
return to their default settings. We advise you to to write 
down your settings so that you can easily reset them 
after the upgrade.
 
■ By Online: Upgrade the software using the Internet.
 
✎First, configure your network. For detailed 
procedures on using the Network Setup, refer to 
the “Network Connection” instructions.
 
✎If the internet connection doesn’t operate properly, 
the connection may be broken. Please retry 
downloading. If the problem persists, download by 
USB and upgrade.
 
■ Alternative Software (backup): Displays the software 
version downloaded through By Online. During the 
software upgrading, When the Upgrade will discontinue 
from last step, this function be activated.
HD Connection Guide
Refer to this information when connecting external devices 
to the TV.
Contact Samsung
View this information when your TV does not work properly 
or when you want to upgrade the software. You can find 
information regarding our call centers and how to download 
products and software.
TV Rear Panel
or
USB Drive
Software Upgrade
$	[	 	 	
By Online
Alternative Software  ----/--/--_-----
U Move    E Enter    R Return
Current Version 2010/01/18_000001
 
						

							30English
Advanced Features
Advanced Features
Network Connection
You can set up your TV so that it can access the Internet through your local area network (LAN) using a wired or wireless 
connection.
 
¦ Connecting to a Wired Network
You can attach your TV to your LAN using cable in three ways:
 
 You can attach your TV to your LAN by connecting the LAN port on the back\
 of your TV to an external modem using a Cat 
5 cable. See the diagram below.
 
 You can attach your TV to your LAN by connecting the LAN port on the back\
 of your TV to a IP Sharer which is connected 
to an external modem. Use a Cat 5 cable for the connection. See the diagram below.
 
 Depending on how your network is configured, you may be able to attach your TV to your LAN by connecting the LAN \
port on the back of your TV directly to a network wall outlet using a Cat 5 cable. See the diagram belo\
w. Note that the wall 
outlet is attached to a modem or router elsewhere in your house.
If you have a Dynamic Network, you should use an ADSL modem or router that supports Dynamic Host Configuration 
Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, 
and DNS values your TV needs to access the Internet so you don’t have to enter them manually. Most home networks are 
Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you must enter the IP address, 
subnet mask, gateway, and DNS values manually on your TV’s Cable Setup Screen when you set up the network 
connection. To get the IP address, subnet mask, gateway, and DNS values, contact your Internet Service Provider (ISP). If 
you have a Windows computer, you can also get these values through your computer. 
 
✎You can use ADSL modems that support DHCP if your network requires a Static IP address. ADSL modems that 
support DHCP also let you use Static IP addresses.
The Modem Port on the Wall TV Rear Panel
LAN Cable (Not Supp ied)
LAN Adapter (Supplied)
Modem Cable (Not Supplied)
External Modem 
(ADSL / VDSL / Cable TV)
The Modem Port on the Wall TV Rear Panel
LAN Cable 
(Not Supplied)
LAN Cable (Not Supp ied)
Modem Cable (Not Supplied)
External Modem 
(ADSL / VDSL / Cable TV) IP Sharer
(having DHCP server)
LAN Adapter (Supplied)
The LAN Port on the Wall TV Rear Panel
LAN Cable (Not Supplied)
LAN Adapter (Supplied)