Samsung Ud55ep Manual

							111
Network
Network  Status
MENU m → Network → Network Status → ENTER E
You can check the current network and Internet status.
Network Status
Wired network and Internet connection settings complete.
You are connected to the Internet. If you have any problems using online services, please 
contact your Internet Service Provider.
Close
Retry
IP Settings
 -
The displayed image may differ depending on the model.
Network  Settings
MENU m → Network → Network Settings → ENTER E
Configure network settings to use various smart hub features such as Internet search, content sharing 
through a home network and feature updates.
Network SettingsSelect your network type.
Network type Wired
Connect
You can connect your 
Device to the internet.
 -The displayed image may differ depending on the model.
Network  type
 •
Wired
Chapter  09             
						

							112
Network Settings (Wired)
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
 •You can attach your product to your LAN by connecting the LAN port on the back of your product 
to an external modem using a LAN cable.
See the diagram below.
RJ45The Modem Port on the Wall External Modem
(ADSL / VDSL)
Modem Cable LAN CableLAN
 •
You can attach your product to your LAN by connecting the LAN port on the back of your product 
to an IP Sharer which is connected to an external modem. Use LAN cable for the connection. See 
the diagram below.
The Modem Port on the Wall
External Modem
(ADSL / VDSL) IP Sharer
(having DHCP server) LAN
Modem Cable LAN Cable LAN Cable
RJ45
 •
Depending on how your network is configured, you may be able to attach your product to your 
LAN by connecting the LAN port on the back of your product directly to a network wall outlet 
using a LAN cable. 
See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in 
your house.
The LAN Port on the Wall LAN
LAN CableRJ45
If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic 
Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the 
IP address, subnet mask, gateway, and DNS values your product needs to access the Internet so you do 
not have to enter them manually. Most home networks are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you must enter 
the IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen 
when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, 
contact your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
 ― You can use ADSL modems that support DHCP if your network requires a Static IP address.
 ―ADSL modems that support DHCP also let you use Static IP addresses.        
						

							113
Set the network connection to use Internet services such as perform software upgrades.
Automatic Network Settings (Wired)
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically
1 Set Network type to Wired from the Network Settings page.
2 Press the Connect button to start Network Settings.
 -
The Connect button is only enabled when the LAN cable is properly connected.
3 The network test screen appears and verifies the network connection.
When the connection has been verified, the “Wired network and Internet connection 
completed.” message appears.
 ―
If the connection process fails, check the LAN port connection.
 ―If the automatic process cannot find the network connection values or if you want to set the 
connection manually, go to the next section, network setup.
Manual Network S ettings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server 
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
1 Set Network type to Wired from the Network Settings page.
2 Press the Connect button to start Network Settings.
 -
The Connect button is only enabled when the LAN cable is properly connected.
3 The network test screen appears and the verification process starts. Press  Stop. The verification 
process stops.
4 Select IP Settings on network connection screen. The IP Settings screen appears.
5 Select the field at the top, press E , and then set IP Settings to Enter manually. Repeat the entry 
process for each field in the IP Address.
 ― Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
6 When done, select OK at the bottom of the page, and then press E . The network test screen 
appears and the verification process starts. 
7 When the connection has been verified, the “Wired network and Internet connection 
completed.” message appears.  
						

							114
Multimedia  Device  Settings
MENU m → Network → Multimedia Device Settings → ENTER E
Allow other devices such as smart phones and tablets on your network, to share content with your 
product.
Server  Network  Settings
MENU m → Network → Server Network Settings → ENTER E
C onnect  to S erver
To run Player connect to a network.
 •
Server Address / SSL / Port
 ―
If the SSL option is enabled, the server is configured to use https and data transfer is encrypted.
 ―Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to 
the server using port number 7001, check with your server administrator to find the correct port 
number and then change the port number.)
M agicI nfo Mode
Select the appropriate MagicInfo Mode depending on the environment where you are using the 
product.
 •
Lite / Premium
Server  Access
Select a method to connect the server network.
 •
Allow / Deny
FTP Mode
Specify the FTP operating mode.
 •
Active  / Passive
Device  Name
MENU m → Network → Device Name → ENTER E
Select or enter a device name.
This name can be shown on network remote controls over the network.
 •
[Signage]Display 1 ~ 6 / User Input  
						

							115
System
A ccessibility
MENU m → System  → Accessibility → ENTER E
Accessibility
Voice Guide
Caption
Menu Transparency
High Contrast
Enlarge Off
Off
Medium Off
Off
 -The displayed image may differ depending on the model.
Voice  Guide
Voice G uide
Switch Voice Guide on or off. The language used for Voice Guide will be the same as the current menu language.
 •
Off / On
 ―
Volume, Speed and Pitch are enabled only when Voice Guide is set to On .
Volume
Set the volume level for the Voice Guide.
 •
High / Medium / Low
Speed
Set the speed of the Voice Guide.
 •Fast / Normal / Slow
Pitch
Tune the pitch of the Voice Guide.
 •
High / Medium / Low
Chapter  10  
						

							116
Accessibility
Voice Guide
Caption
Menu Transparency
High Contrast
EnlargeOff
Off
Medium Off
Off
 -The displayed image may differ depending on the model.
Caption
C aption
You can switch the caption function on or off.
If captions are not available, they will not be displayed on the screen.
 •
Off / On
 ―
The Caption feature does not work with devices connected to the product through the  Component, HDMI1, HDMI2, DVI, 
PC or DisplayPort input jacks.
C aption M ode
You can select the desired caption mode.
 ―
The availability of captions depends on the program being Broadcasted.
 • Default / CC1  ~ CC4 / Te x t 1  ~ Te x t 4 : The analog  Caption function operates in either analog product channel mode or 
when a signal is supplied from an external device to the product.
(Depending on the Broadcasting signal, the analog Caption function may or may not work with digital channels.)  
						

							117
Digital C aption O ptions
Configure the subtitle settings such as size and color.
Adjusts the each option. When done, select Close.
 •
Size: Options include Default, Small, Standard, Large and Extra Large. The default is Standard.
 •Font Style: Select the caption fonts.
 •Font Color: You can change the color of the letters. Options include Default, White, Black, Red, Green, Blue, Yellow, 
Magenta and Cyan . The default is White.
 •
Background Color: You can change the background color of the caption. Options include  Default, White, Black, Red, 
Green, Blue, Yellow, Magenta and Cyan . The default is Black.
 •
Window Color: Select the color you want the window of your digital captions to be.
 •Font Opacity: This adjusts the opacity of text. Options include Default, Transparent, Translucent, Solid and Flashing.
 •Background Opacity: This adjusts the opacity of the caption background. Options include  Default, Transparent, 
Translucent, Solid and Flashing.
 • Window Opacity
 •Edge Type: Select the type of the outline you want on your digital captions.
 •Edge Color: Select the color outline you want on you digital captions. 
 •
Return to Default: Returns to the default settings of the broadcasting station for the captions.
 ―
You cannot set both the Font Color and the Background Color to the same color.  
						

							118
Accessibility
Voice Guide
Caption
Menu Transparency
High Contrast
EnlargeOff
Off
Medium Off
Off
 -The displayed image may differ depending on the model.
Menu  Transparency
Adjust transparency of menu box.
 •
High / Medium / Low
High  Contrast
Set the background and font to high-contrast colors in Menu. Menu transparencies become opaque when the option is 
selected.
 •
Off / On
Enlarge
Set whether to enlarge highlighted item in Menu.
 •
Off / On  
						

							119
Setup
MENU m → System  → Setup → ENTER E
77
System
Accessibility
Setup
Time
Auto Source Switching
Power Control
Eco Solution
Temperature Control
 -
The displayed image may differ depending on the model.
Initial settings (S ystem)
After powering on the product for the first time, configure basic settings such as the language, channel and time.
Press the 
 button.
 ―
Enter your 4 digit PIN number. The default PIN number is “0-0-0-0". 
If you want to change the PIN number, use the Change PIN function.
1 Menu Language
Selecting a language 
Press the  u or 
d button, and then press the 
E button. Specify the OSD menu language.
2 Display Orientation
 -
Landscape / Portrait
Configure the menu page orientation.
3 Network Settings
Set up your network connection. Press the  E button to start. If you do not know your network set up information or 
want to set to it later, select Skip . You can set up the network connection later using the Network menu.
4 Clock Set
Set the current date and time, and then select Next .
5 Play via
 -
MagicInfo / URL Launcher
Select the appropriate player mode depending on the environment where you are using the product.
 ― The Play via setting step only appears when connected to the network.  
						

							120
6 Device Name
 -User Input / [Signage]Display 1 ~ 6
Select or enter a device name.
This name can be shown on network remote controls over the network.
7 Setup Complete
Congratulations! Setup is complete and you're ready to get started.