Samsung Television SyncMaster 400PXn User Manual

Remove the 4 screws on the back of the 
product. 
Insert the screw B into the plastic hanger. 
 
1. Mount the product on the wall bracket and  make sure it is properly fixed to the left and 
right plastic hangers.  
2. Be careful when installing the product on the  bracket as fingers can be caught in the holes.  
3. Make sure the wall bracket is securely fixed to 
the wall, or the product may not stay in place 
after installation.  
Tighten the 4 screws in step 2 (plastic hanger + 
screw  B)to the rear...

1. Fix the product to the wall bracket.  
2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.  
3. You can adjust the bracket angle between -2°and 15 °.   Make sure to use the top center, and not the 
leftor the right side of the product to adjust the 
angle. 

 Mechanical Lay-out
 | Monitor Head  | Stand  | Speaker  | Installation VESA Bracket  | Wall Bracket Installation  
1. Mechanical Lay-out
2. Monitor Head
Dodatak 

3. Stand
4. Speaker
5. Installation VESA Bracket 
zWhen installing VESA, make sure to comply with the international VESA standards.  zPurchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place 
an order. After your order is placed, installation professionals will visit you and install the bracket.  
zAt least 2 persons are needed in order to move the LCD Monitor.  zSamsung is not responsible for any product damage or any injury caused by installation...

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
6. Wall Bracket Installation 
zContact a technician for installing the wall bracket.  zSamsung Electronics is not responsible for any damages to the product or harm to customers when the 
installation is done by the customer.  
zThis product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. 
 
Components
Only use the components and accessories shipped...

There are two hinges(left and right). Use the correct one.
Before drilling into the wall, check if the length 
between the two locking holes at the back of the 
product is correct. 
If the length is too short or long, loosen all or 
some of the 4screws on the wall bracket to adjust 
the length. 
 
A. Length between the two locking holes
Check the installation diagram and mark the drill 
points on the wall. Use the 5.0 mm bit to drill 
holes deeper than 35 mm. Fix each anchor in the 
corresponding hole....

Remove the 4 screws on the back of the 
product. 
Insert the screw 
B into the plastic hanger. 
 
1. Mount the product on the wall bracket and 
make sure it is properly fixed to the left and 
right plastic hangers.  
2. Be careful when installing the product on the 
bracket as fingers can be caught in the holes.  
3. Make sure the wall bracket is securely fixed to 
the wall, or the product may not stay in place 
after installation.  
Tighten the 4 screws in step 2 (plastic hanger + 
screw 
B)to the rear...

1. Fix the product to the wall bracket.  
2. Hold the product at the top in the center and pull it forward 
(direction of the arrow) to adjust the angle.  
3. You can adjust the bracket angle between -2°and 15 °.  Make sure to use the top center, and not the 
leftor the right side of the product to adjust the 
angle. 

Select Language Main Page
Model
The color and appearance of the product may vary depending on the model, and the product specifications are 
subject to change without prior notice for reasons of performance enhancement. 
Connections 
Installing the Stand KIT
 
 
Note
• Only the supplied bolts should be used.
 
Caution
Samsung Electronics will not be responsible for damages caused by using a base other than those 
specified. 
 
Installing the Semi Stand 
 
Left stand Right stand 
Caution
Make sure to...

This stand is designed for adjusting the screen angle. The company is not responsible for any problem 
caused when using this stand. Under no circumstances use the product as a stand for placing something on. 
 
 
Installing the Stand KIT (sold separately) 
 
1) A Cover-Protector is used to protect the hole at the bottom of the LCD Display , where the stand is  inserted. Be sure to remove the Cover-Protector when attaching the provided Semi Stand or Stand KIT 
(sold separately) and cover the hole using...