Samsung Syncmaster B1930hd User Manual

							4-2Installing the Software
4-2 MultiScreen
What is MultiScreen ?
MultiScreen enables you to partition multiple sections on the Monitor.
Installing the Software
1.Insert the installation CD  into the CD-ROM drive. 
2. Select the MultiScreen setup program.
 If the pop-up screen for the software installation does no t appear on the main screen, find and double-click the 
MultiScreen setup file  on the CD-ROM.
 
3.When the Installation Wizard appears, click [Next].
4. Complete the remaining software installation steps a ccording to the instructions displayed on the screen.
 • The software may not work properly if you do not restart the computer after the installation.
• The MultiScreen icon may not appear depending on t he computer system and the product specifications.
• If the shortcut icon does not appear, press the F5 key.
 
MultiScreen Installation Requirements
The MultiScreen installation may be affected by the gra phics card, motherboard and the networking environment. 
Operating System
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista 32Bit
• Windows 7 32Bit
 For MultiScreen, Windows 2000 or later operating systems are recommended.  
Hardware
• At least 32MB of memory 
• At least 60MB of free space on the hard disk drive 
Removing the Software 
Click [Start], select [Settings]/[Control Panel], and then double-cli ck [Add or Remove Programs]. 
Select MultiScreen from the program li st and click the [Add/Delete] button. 
 
						

							Troubleshooting5-1
5 Troubleshooting
5-1 Monitor Self-Diagnosis
 • You can check if the product is working properly using the Self-Diagnosis function.
• If a blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected, perform  the self-diagnosis function according to the procedures below.
 
1.Turn the product and the PC off.
2. Remove the D-Sub cable from the product. 
3. Turn the product on. 
4. If the product is working properly, the   message appears. In this case, if a blank screen is displayed 
again, make sure that there is no problem with the PC and the connection.
 
						

							5-2Troubleshooting
5-2 Before Requesting Service
 Please check the following before requesting After-Sales service. If the problem continues, please contact your nearest 
Samsung Electronics Service Centre.
 
PROBLEMS RELATED TO INSTALLATION (PC MODE)
The monitor screen flickers. Check if the signal cable between the computer and the monitor is securely 
connected and tightened.
(Refer to Connecting to a Computer) 
PROBLEMS RELATED TO SCREEN
Screen is blank and power indicator is off. Ensure that the  power cord is firmly connected and the LCD monitor is on.
(Refer to Connecting to a Computer) 
 message Ensure that the signal cable is firmly connected to the PC or video sources.
(Refer to Connecting to a Computer) 
 message is shown Check the maximu m resolution and the frequency of the video adapter.
Compare these values with the data in the Standard Signal Mode Table. 
Picture rolls vertically. Check if the signal cable is securely connected.Connect it again securely. 
(Refer to Connecting to a Computer) 
Image is not clear. Picture is blurred. Run Frequency  and < Fine> tuning.
Turn on again after removing all accessories(video extension cable, etc.)
Set resolution and frequency to the recommended ranges.
Picture image is unstable and vibrates. Check if the resolution and frequency set for the computer video card falls 
in the range supported by the monitor.  If not, reset them referring to the 
current  under the moni tor menu and Standard Signal Mode 
Table.
Ghost images are shown in the picture.
The image is too light or too dark Adjust the Brightness and Contrast
(Refer to the , ) 
The display brightness can differ according to the mode set for .
If  is set to , the display brightness can 
differ according to the input signal.
Screen is blank and the power indicator light 
blinks every 0.5 or 1 seconds The monitor is using its power management system
Press a key on the keyboard
The screen is blank and is blinking.
If you see the TEST GOOD message on the screen when you press the [ 
MENU] button, check the cable connec tion between the monitor and the 
computer to ensure that the connector is properly connected.
PROBLEMS RELATED TO AUDIO
No sound Ensure that the audio cable is firmly connected to both the audio-in port on 
your monitor and the audio-out port on your sound card.
(Refer to Connecting to a Computer) 
Check the volume level.
The sound level is too low. Check the volume level.
If the volume is still too low after turning the control to its maximum, check 
the volume control on the computer sound card or software program.
 
						

							Troubleshooting5-2
PROBLEMS RELATED TO REMOTE CONTROL 
The remote control buttons do not respond. Check the battery polarities (+/-).
Check if the batteries have been exhausted.
Check if the power is on.
Check if the power cord is securely connected.
Check if a special fluorescent or neon lamp is on in the vicinity
NOTE ON THE PRODUCT APPEARANCE
You may see small particles if you look closely at 
the edge of the bezel surrounding the screen. This is part of the products design and is not a defect.
 
						

							5-3Troubleshooting
5-3 FAQ
FAQPLEASE TRY THE FOLLOWING!
How can I change the frequency of the video sig-
nal? You have to change the frequency of the graphics card.
Windows XP : Change the frequency by selecting Control Panel 
→ 
Appearance and Themes  → Display → Settings  → Advanced  → Monitor, 
and then change the refresh rate under Monitor Settings. 
Windows ME/2000 : Change the frequency by selecting Control Panel   → 
Display   → Settings  → Advanced  → Monitor, and then change the refresh 
rate under Monitor Settings.
Windows Vista : Change the frequency by selecting Control Panel  → 
Appearance and Personalization  → Personalization → Display settings  → 
Advanced settings  → Monitor, and then change the refresh rate under 
Monitor Settings. 
Windows 7 : Change the frequency by selecting Control Panel  → Appear-
ance and Personalization  → Display → Adjust resolution  → Advanced set-
tings  → Monitor, and then change the refr esh rate under Monitor Settings. 
(For more informati on, refer to the User Manual of the computer or the 
graphics card.)
How can I change the resolution? Windows XP : Change the resolution by selecting Control Panel  → 
Appearance and Themes  → Display → Settings. 
Windows ME/2000 : Change the resolution by selecting Control Panel  → 
Display  → Settings. 
Windows Vista : Change the resolution by selecting Control Panel  → 
Appearance and Personalization  → Personalization → Display settings.
Windows 7 : Change the resolution by selecting Control Panel  → Appear-
ance and Personalization  → Display → Adjust resolution.
(For more informati on, refer to the User Manual of the computer or the 
graphics card.)
How can I use the power saving function? Windows XP : Configure it by selecting Control Panel  → Appearance and 
Themes  → Display  → Screen Saver Setting or configure it in the BIOS 
Setup of the computer.
Windows ME/2000 : Configure it by selecting Control Panel  → Di
splay  → 
Screen Saver Setting or Config
 ure it in the BIOS Setup of the computer. 
Windows Vista : Change settings by selecting Control Panel  → Appear-
ance and Personalization  → Personalization → Screen Saver. You can 
also use the BIOS SETUP menu on the PC.
Windows 7 : Change settings by selecting Control Panel  → Appearance 
and Personalization  → Personalization → Screen Saver. You can also use 
the BIOS SETUP menu on the PC.
(For more information, refer to the Windows user manual for the com-
puter.)
How can I clean the outer case/LCD Panel? Disconnect the powe r cord and then clean the monitor with a soft cloth, 
using either a plain water.
Do not leave any detergent  or scratches on the case.
Do not let any water enter the monitor.
 
						

							Troubleshooting5-3
Can I watch digital TV broadcasting with an ana-
logue TV?No.
The analogue TV cannot interpret digital signals. Therefore, a digital TV is 
required to watch digital TV broadcasting.
Can I use my present antenna to receive digital 
broadcasting? As for existing analogue TV, digital TV is designed so that digital broad-
casting signals are received via 
both indoor and outdoor antennas.
If signal reception is very good in your environment, you can watch digital 
broadcasts with your existing indoor ante nna. If not, it is better to install an 
outdoor antenna.
FAQPLEASE TRY THE FOLLOWING!
 
						

							6-1More Information
6 More Information
6-1 Specifications
6-1-1. B1930HD / B2030HD
MODEL NAMEB1930HDB2030HD
LCD PanelScreen Size18.5 inches (47 cm) 20 inches (50 cm)
Display Area409.8 mm (H) x 230.4 mm (V) 442.8 mm (H) X 249.075 mm (V)
Pixel Pitch0.3 mm (H) x 0.3 mm (V) 0.2768 mm (H) x 0.2768 mm (V)
Synchroniza-
tionHorizontal Frequency 30 ~ 81 kHz
Vertical Frequency 56 ~ 75 Hz
Colour 16.7M
ResolutionOptimal Resolution 1360 x 768 @ 60 Hz 1600 x 900 @ 60 Hz (RB)
Maximum Resolution 1360 x 768 @ 60 Hz 1600 x 900 @ 60 Hz (RB)
Input Signal, TerminatedAnalogue(D-Sub port), Digital DVI(HDMI port)
0.7 Vp-p ± 5 %
Separate Type H/V Sync, Composite
TTL Level (V high 
≥ 2.0 V, V low ≤  0.8 V)
Maximum Pixel Clock 85.000 MHz (Analogue, Digital) 108.000 MHz (Analogue, Digital)
Power Supply This product supports 100 – 240 V. Since the standard voltage may differ from 
country to country, please check the label on the back of the product.
Dimension (Width x Height x Depth) / 
Weight 455.6 x 309.4 x 67.7 mm (17.9 x 12.2 x 
2.7 inches) (Without Stand) / 4.05 kg 
(8.9 Ibs)
455.6 x 375.0 x 178.0 mm (17.9 x 14.8 x 
7.0 inches) (With Stand) / 4.25 kg (9.4 
Ibs)492.4 x 311.2 x 67.5 mm (19.4 x 12.3 x 
2.7 inches) (Without Stand) / 4.53 kg 
(10.0 Ibs)
492.4 x 407.5 x 197.0 mm (19.4 x 16.0 x 
9.6 inches) (With St
and) / 4.77 kg (10.5 
Ibs)
VESA Mounting Interface  75 mm x 75 mm (2.95 inches x 2.95 inches)
Environmental 
considerationsOperating Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Tilt 0° ~ 20° (±1°)
 
						

							More Information6-1
 6-1-2. B2230HD / B2330HD / B2430HD
 Design and specifications are subj ect to change without prior notice.  Class B (Information Communication equipment for residential use)
This device is registered for EMC requir ements for home use (Class B). It can be  used in all areas. (Class B equipment 
emits less electromagnetic waves than Class A equipment.)
 
MODEL NAMEB2230HDB2330HDB2430HD
LCD PanelScreen Size 21.53 inches (54 cm) 23 inches (58 cm) 24 inches (61 cm)
Display Area 476.64 mm (H) x 268.11 
mm (V) 509.76 mm (H) X 286.74 
mm (V)531.36 mm (H) X 298.89 
mm (V)
Pixel Pitch
0.24825 mm (H) x 
0.24825 mm (V) 0.2655 mm (H) x 0.2655 
mm (V)0.27675 mm (H) x 
0.27675 mm (V)
Synchroniza-
tionHorizontal Frequency 30 ~ 81 kHz
Vertical Frequency 56 ~ 75 Hz
Colour
16.7 M
ResolutionOptimal Resolution 1920 x 1080 @ 60 Hz
Maximum Resolution 1920 x 1080 @ 60 Hz
Input Signal, TerminatedAnalogue(D-Sub port), Digital DVI(HDMI port)
0.7 Vp-p ± 5 %
Separate Type H/V Sync, Composite
TTL Level (V high 
≥ 2.0 V, V low ≤  0.8 V)
Maximum Pixel Clock 148.500 MHz (Analogue, Digital)
Power Supply This product supports 100 – 240 V. Since the standard voltage may differ from 
country to country, please check th e label on the back of the product.
Dimension (Width x Height x Depth) / 
Weight 523.8 x 350.6 x 67.8 mm 
(20.6 x 13.8 x 2.7 inches) 
(Without Stand) / 4.66 kg 
(10.3 Ibs)
523.8 x 416.7 x 197.0 mm 
(20.6 x 16.4 x 7.8 inches) 
(With Stand) / 4.91 kg 
(10.9 Ibs)560.4 x 370.0 x 67.9 mm 
(22.0 x 14.6 x 2.7 inches) 
(Without Stand) / 5.15 kg 
(11.4 Ibs)
560.4 x 436.7 x 197.0 mm 
(22.0 x 17.2 x 7.8 inches) 
(With Stand) / 5.5 kg 
(12.1 Ibs)582.0 x 381.8 x 67.9 mm 
(22.9 x 15.0 x 2.7 inches) 
(Without Stand) / 5.45 kg 
(12.0 Ibs) 
582.0 x 448.0 x 197.0 mm 
(22.9 x 17.6 x 7.8 inches) 
(With Stand) / 5.8 kg 
(12.8 Ibs)
VESA Mounting Interface 
75 mm x 75 mm (2.95 inches x 2.95 inches)
Environmental 
considerationsOperating Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Tilt 0° ~ 20° (±1°)
 
						

							6-2More Information
6-2 Power Saving Function
This product provides a power saving function that automatically turns the screen off when the product is not used for a 
predetermined period of time to reduce power consumption. If t he product enters power saving mode, the power LED turns to a 
different Colour to indicate that the product is in power saving mode. When the product is in power saving mode, the power is not 
turned off and you can turn the screen on again by pressing any  key or clicking the mouse. However, the power saving function 
only works when the product is connected to a co mputer that provides the power saving function.
 • The actual power consumption may be different from the indicated power consumption above if the system conditions or 
settings are changed.
• If there is no power cut-off switch, the power consum ption is 0 only when the power cord is disconnected.
• DPM(Display Power Management) Function does not work if  you used in conjunction with the [HDMI(DVI) IN] port of 
this product. 
 
POWER SAVING  FUNCTIONNORMAL OPERATIONPOWER SAVING MODE
(DPM)POWER OFF
(POWER BUTTON)
Power LED OnBlinks Off
Power Con- sumption B1930HD
33
34
47
58
52 watts
Analogue : less than 0.3 
watts less than 0.3 watts
B2030HD  watts
B2230HD  watts
B2330HD  watts
B2430HD  watts
 
						

							More Information6-3
6-3 Contact SAMSUNG WORLDWIDE
 If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. 
EUROPE
AUSTRIA 0810 - SAMSUNG(7267864,€ 0.07/min) http://www.samsung.com
BELGIUM 02-201-24-18http://www.samsung.com/be (Dutch)
http://www.samsung.com/be_fr 
(French)
CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com
DENMARK70 70 19 70http://www.samsung.com
EIRE 0818 717100http://www.samsung.com
ESTONIA 800-7267http://www.samsung.com
FINLAND 030 - 6227 515http://www.samsung.com
FRANCE 01 48 63 00 00http://www.samsung.com
GERMANY 01805 - SAMSUNG (726-7864,€ 0,14/
Min) http://www.samsung.com
HUNGARY 06-80-SAMSUNG(726-7864)http://www.samsung.com
ITALIA 800-SAMSUNG(726-7864)http://www.samsung.com
LATVIA 8000-7267http://www.samsung.com
LITHUANIA 8-800-77777http://www.samsung.com
LUXEMBURG 261 03 710http://www.samsung.com
NETHERLANDS 0900 - SAMSUNG (0900-7267864) (€ 
0,10/Min)http://www.samsung.com
NORWAY 815-56 480http://www.samsung.com
POLAND 0 801 1SAMSUNG (172678)
022 - 607 - 93 - 33 http://www.samsung.com
PORTUGAL 80820 - SAMSUNG (726-7864) http://www.samsung.com
SLOVAKIA 0800-SAMSUNG(726-7864)http://www.samsung.com
SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com
SWEDEN 0771 726 7864 (SAMSUNG)http://www.samsung.com
SWITZERLAND 0848-SAMSUNG(7267864, CHF 0.08/
min) http://www.samsung.com/ch
http://www.samsung.com/ch_fr (French)
U.K 0845 SAMSUNG (7267864) http://www.samsung.com
CIS
ARMENIA 0-800-05-555
AZERBAIJAN 088-55-55-555
BELARUS 810-800-500-55-500
GEORGIA 8-800-555-555